Search Documents

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By Randy Fulton, Ignacy Puszkiewicz, George H. K. Schenck

Stuart Olson Construction, Inc. excavated 385m (1263 ft.) long twin tunnels with 6.25m (20.5 ft.) O.D., a portal and a cross-over for the Edmonton, "Metro". The work for Contract No. 76458, SLRT South Tunnel and Portal, in Edmonton, Alberta, Canada was performed in 1989 and 1990. NATM was specified because of the instability of glacial deposits. The contractor decided to use "two firsts" on this project: Fully mechanized NATM and a novel excavator¬mounted tunneling machine. An excavator was equipped with a cutter boom, and a loading and conveying system. This novel machine cost only about one-third of the price of a special NATM roadheader. This new combination of NATM and an excavator-mounted cutter boom offered a cost-effective alternative to shields, slurry TBMs and roadheaders for short tunnels in unstable ground. For NATM tunneling in hard rock or in mixed faces, the roadheader-type cutter boom can be replaced with an impact hammer (hydraulic breaker).

Jan 1, 1993

By José Luis Lee Moreno

This paper presents a preliminary phase of a study being conducted by the Department of Geochemistry of the Consejo de Recursos Naturales No Renovables in the vicinity of the Pachuca-Real del Monte Mining District. This district is located in central Mexico, about 100 km northeast of Mexico City. It has been in operation for the past 450 years and has produced about 38 million kg of silver and about 190 thousand kg of gold. At the present it is being worked by the state owned mining company of Real del Monte and Pachuca. The rocks of the area consist mainly of Tertiary volcanics, ranging in age from early Oligocene to late Pliocene. Ore bodies are recognized as epithermal, vein type fracture fillings. The main ore minerals are argentite and acanthite normally accompanied by base metal sulphides, Gold is present in small amounts as native gold and in other minerals. Orientation geochemical studies performed on soil and rocks over known veins in the district, showed zinc to be the best indicator. Lead and silver anomalies are restricted to the immediate vicinity of the veins, mercury shows the mineralized structures only when the "C" horizon is sampled, while antimony gave erratic values. The El Chico area is about 10 km north of the Pachuca-Real del Monte district and covers approximately 400 sq km. Geological evidence indicated the possibility of an extension of the Pachuca ore bodies in this area. Results obtained from soil and rock samples from El Chico, showed several anomalous area. Detailed investigations proved these anomalies to be related to faults and fractures which in several cases have been found to be mineralized. Drilling is planned with preliminary results expected by late 1974.

Jan 1, 1974

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By R. Q. Honaker

Recent studies conducted at Virginia Tech have shown that ultrafine coal particles can be selectively coagulated and separated from mineral matter without the use of traditional agglomerants or flocculating agents. This technique utilizes hydrophobic interaction forces to induce coagulation of coal particles, while particles of mineral matter are dispersed using pH control. After selective coagulation, the coal coagula can be recovered by a sedimentation technique. In the present work, factors such as pH, particle size, and solids concentration have been examined. A wide range of coal samples have been successfully upgraded using this technique.

Jan 1, 1991

By B. K. Parekh

Silicon carbide (SiC) can be produced by heating rice hulls to elevated temperature, The product is a mixture of beta crystalline silicon carbide whiskers, particles and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 micron in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean high grade Sic whiskers product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90 percent. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1985

By T. P. Meloy

In the last decade increased and prolonged interest has been displayed in the use: of tunneling or rapid excavation to solve many of the urban and industrial problems confronting our society. There has been talk and action on the interurban rapid transit systems for major cities, and even preliminary designs for a Boston to Washington interurban transit system. Much of this interest stems from the search to the solution of our increasingly complex urban problems, where the surface area must be given over more and more to the inhabitants, and the subsurface for transit, utility and other services. While tunneling is not a panacea to urban ills it holds a real solution to many existing problems. There is also, among the tunneling experts, a growing confidence that technical problems of rapid tunneling can be solved. To solve these problems, R & D money must be invested. If it is to be money invested either by private industry or governments, there must be significant returns on the investment to justify the research and development need to bring about the breakthrough that will make tunneling a major contribution to the solution of urban problems. To make these economic studies more extensive and more accurate tunneling demand figures were needed. To this end, the Organization of Economic Cooperation & Development - OCED - included in its Conference on Tunneling a section on tunneling demand. As a result of the conference the organization for Economic Cooperation and Development issued a report entitled "The Advisory Conference on Tunneling - Report on Tunneling Demand 1960-1980. " This report was presented at the OCED Conference on Rapid Excavation, held at Washington, D.C. To obtain the data in the Report, questionnaires were sent to the OCED countries and 18 replies were received from Australia, Austria, Belgium, Canada, Denmark, France, Germany, Ireland, Italy, Japan, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom, and the United States. While it is true, that data were missing, that sometimes the definitions were confused, and that several countries provided no cost estimates at all, in general, this report contains the most comprehensive gathering of data that ever existed in the field. All data in the OECD report is expressed in terms of meters or cubic meters, and costs are in U.S. dollars.

Jan 1, 1970

By Fernando de Oliveira Durão

A complete computer package for the steady-state simulation, either in analysis or in design mode, of mineral processing flowsheets is described. The main features of the simulation package are: modular architecture, flexible structure and sequential solution strategy. Different detail levels of mathematical models of several mineral processing unit operations have been developed and implemented as unit modules (FORTRAN routines). Unit operations currently modelled are: coarse/fine crushing, grinding, screening, hydrocyclone classification, gravity separation, heavy media separation, froth flotation, high gradient magnetic separation and solid-liquid separation. In design mode, a simulation study is stated as a general non linear optimization problem. The objective function is a weighted sum of square deviations between the design specification set points and the calculated values, subject to non linear equality and inequality constraints. The optimization problem solution is obtained solving successive Quadratic Programming subproblems followed by inexact line search of an exact penalty function (Powell algorithm). One non trivial example is discussed, illustrating the design capabilities of the simulation package.

Jan 1, 1992

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By M. L. Mellish

In 1989, for the third consecutive year, both the production and consumption of coal in the United States reached record levels. Domestic coal consumption totaled 806.5 Mt (889 million st) in 1989, a 5.4 Mt (6 million st) increase from the year before (Table 1). US coal exporters also had a banner year. For the first time since 1982, exports ex¬ceeded 91 Mt (100 million st). US coal production in 1989 rose by a surprising 27.3 Mt (30 million st), reaching 889 Mt (980 million st) for the year. To a certain extent, the sizable difference between production and demand growth was due to smaller consumer stock withdrawals. Coal consumers withdrew only 12.7 Mt (14 million st) of coal from their stocks in 1989, com¬pared to 22.7 Mt (25 million st) in 1988. Despite strengthening coal consumption, exports, and production, coal prices to all domestic sectors declined slightly during the year. That essentially continued the trend of the past several years. On the labor front, the United Mine Workers of America struck the Pittston Coal Group in 1989. It was a bitter work stoppage that was not settled until February of 1990. This was the first major coal strike since 1985. The strike also precipitated a series of wildcat outages by UMWA members in June and July. At their peak, more than 40,000 UMWA members participated in the wildcat strikes. Except at Pittston, however, most miners were back to work by August. It is estimated that perhaps 4.5 to 9.1 Mt (5 to 10 million st) of coal production was lost due to the Pittston and associated wildcat strikes. However, some of this production may have been recouped by other coal companies not affected by the wildcat strikes, and by the affected companies after the strikes ended.

Jan 1, 1990

By B. K. Baird, P. C. Satchwell

The application of cutoffs during and after pit optimization is examined for a lower-grade multimetallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block. The calculation incorporates parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which parameters have significant effects on the total contained resource tonnage and total contained nondiscounted revenue in the optimized pit. The cumulative effects of changing several of the more-significant parameters are investigated The application of a copper cutoff grade to a block inside the optimized pit could result in the less-than-optimal extraction of the resource. A block with a copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher-copper-grade block may be subeconomic. Also discussed are the merits of applying a copper-grade cutoff, an "equivalent-grade" cutoff and a dollar-per-ton cutoff to blocks inside the optimum nit.

Jan 1, 2002

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968