Search Documents

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By D. E. Ranta, M. W. Ganster, A. D. Ward

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1992

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By Carlon C. Chambers

INTRODUCTION Manufacturer sponsored research over the past three years has proven the suitability of styrene-butadiene/ asphalt membranes in many waste disposal seepage control applications for the mining industry in general and uranium mining and milling in particular. The class of membranes that have been tested are SBR/asphalt blends containing up to 68 weight percent asphalt, the balance being elastomeric polymers, fillers and phase compatibility promoters. These membranes are classified as thermoplastic, elastomeric materials and can be hot spray applied to any moderately dry substrate at 177°C (350°F), and placed in service within one hour of application. The properties of this membrane that make it suitable for use as an engineering_ material in these applications are discussed. These properties include chemical resistance, bacterial resistance, UV light resistance, permeability, stress/strain characteristics and bonding data. The favorable economics of the system are also discussed. The preliminary raw test data on the above properties were reported in a previous paper, (Chambers, 1980) and most will not be repeated here. Instead, this report considers the original data in relation to subsequent data and concentrates on interpretation of the trends for engineering purposes. However, several of the pictures contained in the original paper are reproduced in this report for illustration purposes. BACKGROUND Asphalt alone has a long history of use as a water-stop material. Its limitations of becoming brittle when cold and soft when hot, however, are well recognized. The service temperature for common grades of asphalt is usually in the 4° to 49°C (40° to 120° F) range. Modifications to the base asphalt can generally improve its performance at the high end of the temperature range by raising its softening point, but only the addition of one class of modifiers, elastomeric polymers, improves low temperature flexibility as well and also adds resilience. Both of these properties are of extreme importance if the waterstop material is to maintain its integrity when used on substrates which are unstable, non-cohesive, discontinuous or have significant expansion/constraction coefficients. Although there are many elastomeric polymers which can be used with

Jan 1, 1980

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By J. N. Albright

Both microgravimetry and crosshole seismic tomography are means by which subsurface collapse and rock failure may be observed. We show results of calculations that predict changes in gravity and gravity gradient that result from void migration, bulking, and hydrology disruption due to room and pillar mining. Crosshole seismic tomography also holds promise for detecting and mapping changes in structure during subsidence. Commercially avail- able logging tools, advances in theory, and recent field results strongly suggest tomographic surveys are now possible. Subsidence phenomena which may be located are faulting, joint separation, bed parting, water table changes, and formation outgassing.

Jan 1, 1982

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By O. M. Bishop

Large reserves of copper are contained in waste dumps which have been created by open-pit mining of porphyry-type copper deposits in the Western United States. Nearly 6 billion tons of copper-bearing material exists in the waste dumps at present, and another billion tons will be added each three to four years as additional material is stripped from the present mines and new open-pit mines are developed. The dumps constitute an enormous resource containing some 7 to 10 billion dollars worth of copper. Increased attention is being given to the recovery of copper by leaching from these dumps as attested by the fact that in 1968 approximately $175 million of copper was recovered by leaching operations. During the leaching process, however, numerous problems exist which prevent complete extraction of the copper from the dumps. Probably the most important problem encountered is the incomplete contact of the copper-bearing materials by the leaching solutions. This problem is mainly created by the formation of physically compacted and chemically cemented layers within the dumps which prevent solution flow to many sections of the interior of the dumps.

Jan 1, 1970

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. W. Hoffman

A fairly recent development in the field of particle separation is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing as such is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages to be gained by the use of probability sizing vs. conventional screening methods are: reduced space requirements for a high capacity unit, fewer moving parts, more versatile product sizing selection, reduced maintenance requirements and lower power consumption.

Jan 1, 1968

By S. E. Phillipson

Underground mine mapping is a critical component of understanding the controls on ground instability. Many relatively localized examples of ground failure are associated with geologic features, such as faults, joints, compaction zones, or sedimentological transition zones. In contrast, long-running, directional roof falls are associated with regionally directed horizontal stress fields, which are induced by tectonic plate interactions in the earth?s crust. When stress-related features are distinguished from geological features, underground mapping can be an effective method for inferring the direction of horizontal stress at individual mines. Comparisons with data compiled in the World Stress Map confirm that underground mapping can be a valid method for determining the orientation of maximum principal horizontal stress at a variety of scales, ranging from individual mines to an entire mining district or coal basin. Comparisons are presented between the maximum horizontal stress directions inferred by MSHA?s Roof Control Division through underground mapping and the azimuths of maximum horizontal stress in the World Stress Map database for North America?s Pennsylvanian-aged Appalachian, Illinois, Black Warrior, and Arkoma Basin coal fields. The comparison indicates that azimuths are similar for both data sets, even where variations in the direction of horizontal stress are present. It is interpreted that inconsistencies in direction are attributable to near-surface affects such as deeply incised stream valleys, or to fault zones that represent heterogeneities in the crust.

Jan 1, 2009

By Boghani. A. B.

A computer program has been developed to simulate evacuation of a mine in various configurations. The simulation input variables include characteristics of the mine, expressed, in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e. , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effects of the fire are not considered. The simulation output include the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure of the miners. Several illustrative simulations have been carried out to verify validity of the program and to demonstrate its capabilities. The computer program has been able to predict evacuation time, within 5 percent, for an actual fire drill. It is believed that this program can be used to evaluate evacuation performance of a mine, identify problem areas and demonstrate improvements due to the recommended corrective actions.

Jan 1, 1977

By D. Yadon, P. Lee, W. Kelly, C. Stilwell

Rico is a small town in an old zinc mining district in a mountain valley of southeastern Colorado. Mine waste rock and mill “tailings” remained after over 100 years of mining in the area, leaving associated surface water and groundwater impacts. Atlantic Richfield Company is proposing an innovative approach, which uses lime precipitation and wetland ponds (semi-natural system, also called treatment lagoon in a wetland setting) to treat adit water in the Rico area. Besides using a non-conventional treatment approach, a non-conventional (non-Superfund) regulatory/administrative approach is being proposed. This paper will focus on the water treatment issues and solutions, as well as describing the innovative “watershed” regulatory process.

Jan 1, 2004

The deformation, failure, and filling characteristics of a caving roof in the initial and normal mining stages of a pitching oblique longwall mining area are analyzed using large-scale threedimensional physical-similitude experiments and numerical calculations to study the characteristics of roof fracture and migration in a steeply dipping seam. The results show that the roof fracture development has evident sequential and spatial characteristics. Among them, immediate roof breaking in different parts of the mining area shows difference in time and space. The failure sequence of the immediate roof in different areas changes with the mining; unique regional stability evolution characteristics are observed in the suspended immediate roof simultaneously, resulting in its significant regional stability on the goaf filling.

Jan 7, 2020

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013