Search Documents

By William Hodder, Lisa Smiley, Ehsan Alav

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km and be lined using a precast concrete segmental tunnel liner with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT liner was grouted through ports drilled in the segments. The Westerly Storage Tunnel (WST) in Cleveland will extend approximately 2.93 km long and will be lined by using a similar precast concrete segmental tunnel liner with an internal diameter of 7,620 mm and external diameter of 8,230 mm. The WST liner was grouted using both grout ports built into the tail can of the TBM and through segments. Each tunnel was mined primarily in shale with varying levels of weathering and both tunnels had dry and wet sections. This paper will document the means and methods for grouting in each tunnel as well as the methods utilized to proof grout and the results found.

Jun 13, 2021

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By S. J. Ristorcelli

Historically, geologic data has not been adequately considered in resource estimation. More recently, with the use of computers and sophisticated estimation algorithms and geostatistical justifications, geology has been downplayed further. Many reasons are given for not using geology including cost, time and irrelevance. None are valid. Boundaries defining mineral domains should be used in computer-generated resource estimates. Selected case histories show how the failure to honor geology has caused discrepancies in resource estimates of actual in-place resources. After-the-fact differences have included decreases in tonnage of up to 50% and increases up to 300%; partial to complete recategorization of material; and 50% decreases in grade. The costs of gathering and using geology are trivial compared to the potential consequences.

Jan 1, 1994

By Joel D. Hammond

Lightweight concretes date back to before the Roman Empire. The earlier concretes were made by combining a burnt lime for cementious material with pumice or volcanic rock for aggregate. Although structural value was limited due to its primitive nature, many structures were able to withstand the test of time. The rotary kiln expanded shale industry had a slow start that began around 1908. The industry was founded by Stephen J. Hayde of Kansas city, Missouri. Mr. Hayde noticed that the bloating effects of some aggregates were undesirable by the brick industry. Material of this type was considered waste and avoided in brick production, but he realized it had all the qualities and basic requirements for a concrete aggregate that would reduce weight and still retain structural value. It came into national attention by use in ocean-going vessels through a shipbuilding program undertaken by the united states Fleet Corporation. This research was brought about by the need to find a suitable material to replace high-grade plate steel due to a shortage created by World War I. The need prompted the government to supply the reserves that Stephen Hayde desired to continue and complete research into producing a uniform lightweight aggregate. His results pointed to the rotary kiln method for which he was granted a patent in 1918. One of the most famous and largest concrete ships built through this program was the U.S.S. Selma. Although the Selma

Jan 1, 1977

By Carrie Smith

In a major milestone for geoscience, the U.S. Geological Survey (USGS) has unveiled the Cooperative National Geologic Map, the most detailed national-scale geologic map of the country to date. The project offers a fresh, layered look at the rocks and sediments that make up the United States. For geologists, engineers and mining professionals, it provides both a technical achievement and a practical tool that will help shape future exploration and landuse decisions across the country. The new map provides a regional view of geology both on and beneath the Earth’s surface. Using different colors to represent rock types and sediments, it allows users to toggle through multiple layers, revealing for the first time the surficial and quaternary deposits that lie above the bedrock. “This is the first national map to include multiple layers of mapped geology, the first built to be easily updated as new maps are published, and the first to be delivered in a user-friendly online interface,” said Joseph Colgan, a USGS research geologist who led the development team. The Cooperative National Geologic Map is a culmination of more than a century of collaborative mapping between the USGS and the nation’s state geological surveys. More than 100 existing maps produced by state geological surveys and the USGS over the past 40 to 50 years were combined and standardized to create the national data set. During its three-year creation, the USGS prepared digital data, built the system to bring the maps together, developed the web interface and underwent a review and approval process. Through this process, decades of fieldwork, analysis and digital cartography were brought together to provide both national and local expertise.

Nov 1, 2025

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By H. S. Duzgun, N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline’s long-term availability, to develop preventive maintenance plans and to make future projections about the dragline’s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, Page 736 and Marion 7820, which have been operating in the Tunçbilek openpit coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data and (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (15.29 m3) seemed to be more reliable and less likely to fail when compared with Marion 7820 (30.58 m3). The operating hours without failure range from 41 to 51 hours with 50% reliability.

Jan 1, 2011

By O. J. C. Runnalls

Canada has played a significant role in the international uranium industry for some three decades. Although there have been many challenges in the past, the future offers a more extensive range of problems and prospects as Canada moves to expand its activities in all aspects of the nuclear fuel cycle. World uranium demand could grow to an annual requirement of 500,000 tons U308 by the year 2000. A substantial fraction of this material is likely to come from Canada because the country&apos;s reserves and resources are large, and because of a favourable geological potential for future discoveries. There has been a long history of association between the producing industry and the federal government, and it has provided the foundation for existing national uranium policies. Close industry-government association will be maintained and developed in future because of the anticipated rapid growth of the industry and the consequent need for continual refinement of government policies relating to exploration, mining, processing and export of uranium.

Jan 1, 1975

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

By Carl P. Venzke

Mining lignite in the Gulf Coast often requires some interaction with shallow ground water system. Suggestions for determining ground water data and analysis requirements for regulatory compliance are given. Simple methods for estimating mine inflow seepage, ground water level declines, and changes in ground water chemistry, which may result from mining, are discussed. The mining of lignite often results in interaction with shallow ground water systems. An evaluation of the interaction is required as input to mine permitting and engineering. Your evaluation will proceed more smoothly and produce more meaningful results with some planning prior to performing your evaluation. The following are tips to consider in planning and carrying out a successful study.

Jan 1, 1982

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997

By T. A. Laser

"INTRODUCTION A positive workplace environmental, health, and safety (EHS) culture affords organizations and corporations many benefits, including increased trust and employee morale, sustainable EHS performance improvements, and reliable productivity and profit margin growth. Unfortunately, many leaders and EHS professionals struggle daily to achieve and maintain positive workplace cultures and consistent business results. While lack of management support, corporate or employee buy-in, resources, and time are common factors that conflict with an EHS culture and safe work behaviors and processes, there are many other actions that threaten the positive attributes of an organization’s culture. Often these culture killers are not recognized, or worse yet, ignored because they are considered taboo. For example, voicing observations or questioning long-held management practices or process that were initially designed to promote EHS values, but no longer do so. Unfortunately, this could be viewed as challenging authority, not being a team player or even not valuing EHS. And for those that speak up, the potential for negative consequences can be real impediments to positive change. Having an open mind, constantly striving to identify culture killers, and putting forth the effort to eliminate them are the first steps to begin reaping the benefits of having a sound workplace culture. This paper helps readers to: • Recognize culture killers that negatively impact fostering and maintaining sustainable EHS cultures in the workplace. • Understand how to prevent, avoid, and respond to culture killers, before they wreak havoc in your organization. • Assess EHS culture strength, and implement plans to continuously improve it. The desire to draw boundaries around concepts, put things into boxes, and nail down requirements for something that is virtually impossible to solidify for any length of time is quite fascinating! These desires can pose challenges when trying to define what the perfect EHS culture should look like. The very act of trying to define our culture tends to create silos, and these silos, in turn, can become “culture killers”. The following is one of the most common culture killers. UNBALANCED ORGANIZATIONS TRIGGER CULTURE KILLERS Unbalanced organizations occur when an organization’s constantly shifting focus forces other important needs to take a back seat--until the focus changes again. This balancing act can be detrimental and lead to catastrophic results including low morale, lack of trust, employee dissatisfaction, high turnover, increased incidents, poor profit margins, loss of market share, and ultimately into organization-wide failure."

Jan 1, 2018

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

By Toyohisa Fujita, Mitsuo Mamiya, W. Tai Yen, Hiroki Kogita

Green algae taken from an acidic mine drainage and blue-green algae taken from an alkaline hot spring stream were collected and tested for their ability to recover or remove dilute metal ions. Experimental results demonstrated that unwashed blue-green algae and washed green algae effectively adsorbed base metals ions and eluted them at pH 1. It was also found that washed and dried algae adsorbed precious metal ions more effectively than unwashed algae. For example, the washed and dried blue-green algae was capable of adsorbing 0.31 kg of gold per kg of algae. The gold from tetrachloroaurate solution which was adsorbed on washed blue- green algae was found to change to a metallic state following initial metal binding. In the case of a dilute gold complex solution leached with thiourea, only a small amount of gold could be captured by algae. Further experiments were conducted on components of the algae, such as alginic acid, agar, cellulose and chitin and mixtures of these components, in order to determine their contribution to metal adsorption characteristics. However, a mixture of these two components demonstrated both good adsorption and desorption characteristics indicating an interaction between the individual components.

Jan 1, 1995

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

"Longwall shearers are widely employed in underground coal mines. The reliability of such machine has significant importance for successful mining operations. This paper aims at studying reliability of a longwall shearer using failure data recorded for a year. Data was pre-processed, sorted and selected for analysis. Selected data is then examined using statistical models. Distribution fitting of time-between-failure (TBF) and time-to-repair (TTR) are accomplished using three different models. Goodness-of-fit criteria is used to ascertain the best fitting model. Reliability in terms of mean-time-between-failure (MTBF), and mean-time-to-repair (MTTR) are calculated using the model which best represents the failure data. Exponential distribution best represents the time between failure and lognormal distribution the time to repair data. A well-known risk management technique Failure Mode Effect and Criticality Analysis is used to evaluate the critical breakdowns. Critical system/parts, experiencing regular failures is delineated based on this analysis. INTRODUCTION Mining is a capital intensive process, and huge monetary investment is required to develop and operate a mining project. Heavy and expensive equipment’s are employed in development and operation of these projects. In order to ensure timely completion of set milestones, it is mandatory that equipment’s perform their required task productively. Delays are not unusual owing to breakdown of these equipment’s. Breakdown or failure experienced by any of the equipment pose heavy financial burden. Moreover, frequent times, companies have to employ and dedicate additional resources to make up for such delays. Delays in project is not only detrimental to company’s image in market, but it also interrupts customer commitments. Mines having history of not fulfilling their promise usually get lower commodity price. Penalties are also imposed on the companies defaulting its obligations. Especially, in today’s world where competition among the companies are growing, success means keeping up the commitments in a timely manner. Heavy machinery and equipment are instrumental in success of any project. These machinery and equipment’s have to reliable in a sense that they can perform the set task in given time period. Reliability of these equipment plays a pivotal role in success of any project. The reliability analysis of mining equipment has long history. Many researchers have applied different statistical models for analyzing the reliability of mining machines (Samanta, Sarkar [1]. Kumar and Klefsjö [2] demonstrated the use of the power law process model for reliability assessments of repairable mining machines. Barabady and Kumar [3] performed the reliability analysis from failure data of the crushing plants."

Jan 1, 2018