Search Documents

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By W. G. Lacy

Anticipation of problems and the adoption of corrective measures in the design of engineering structures, establishment of pertinent building codes, and urban planning and zoning to obtain optimum land usage and conservation of natural resources demands a thorough understanding of geological conditions of a developing urban area. In the and to semi-arid southwestern United States erosional and depositional processes result in special situations that require special precautions in building practices. A series of studies currently underway in the Tucson area prompted by foundation failures and breaking, of buried service lines serve to illustrate some of these relationships between the geological environment and history, and engineering problems.

Jan 1, 1963

By Gordon R. S. Smith

This paper is in two parts. The first part describes Membrane Back-Pulse Filtration and the effects of very short filter downtimes on cycle filtration rates. Part II describes the use of Membrane Back-Pulse Filtration for combined thickening and polishing soda ash thickener feed material followed by a description of computer modeling of CCD circuits by Iterative solver.

Jan 1, 1991

By Richard I. Grass

The White Pine Mine is located 4- 1 /2 miles south of Lake Superior in the western part of Michigan's Upper Peninsula. The orebody occurs in tabular, gently dipping Keweenawan sediments. GEOLOGY The orebody outcrops beneath 30-50 feet of Pleistocene clays and dips to the east and northeast to a depth of 3, 000 feet in five miles. It lies midway between the Porcupine Mountains and the Bergland Hills, both of which are steeply dipping felsite and coarse porphyry intrusives, extrusives and sediments (Figures 1 and 2). The orebody sediments were deposited in the Keweenawan basin during mid- and upper Keweenawan times. Mineralization occurs in the basal 20 to 25 feet of the Nonesuch formation, which is made up primarily of laminated siltstone s. Native copper, chalcocite, and silver are the ore minerals. The ore is mined by trackless room-and-pillar methods.

Jan 1, 1967

By A. K. Sinha

Inspite of the growing demands worldwide, thermal coal must compete in the market both in price and quality. The design and performance efficiency of coal preparation plants is thus crucial to the survival and profitability of a coal industry. While the coal recovery influences the cost of production, the quality produced by a preparation plant determines the selling price. Several coal preparation plant simulation models have been developed in recent years to help Improve the performance of coal preparation plants. A research project was recently conducted at Southern Illinois University to evaluate the practical applicability of such a model. The results of this study are presented and discussed.

Jan 1, 1986

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By C. M. Sliepcevich

This paper is a brief status summary of investigations by the authors over the past decade to develop a continuous process for recovering' high purity metal powder from pregnant solutions by gaseous reduction at elevated temperatures and pressures. Although these studies included extraction of other metals such as nickel, silver, and gold, this presentation will be confined to the hydrogen reduction of acidic and ammoniacal solutions of copper. The continuous hydrogen reduction process (CHR) described herein enjoys the environmental advantages of other hydrometallurgical processes but, in addition, provides a substantial benefit in fuel economy over competing processes. As was recognized by Schaufelberger in 1956, for a given amount of fuel a continuous hydrogen reduction process has the potential for producing four to six times as much metal as an electrolysis process (1). Although hydrogen reduction of metal salt solutions has been known for more than a century, extensive development work leading to commercialization was not initiated until the 1950's. Since then, commercial applications relative to other extractive techniques have been minor and have been confined to batch or to continuous, completely-mixed autoclaves. By contrast, the process described herein utilizes a continuous, tubular reactor which is operated in modified plug flow so that only limited and localized backmixing occurs. Thus, gradients in concentration, temperature, and pressure exist over the length of the reactor, the presence of which can be utilized to advantage for achieving high conversions and product quality (2, 3).

Jan 1, 1975

This paper addresses the valuation and development timing of an undeveloped mineral project. Traditional analysis has us developing the project immediately if its net present value (NPV) is positive. Option pricing theory finds that it is better to wait until the NPV of the property is significantly greater than zero before developing. Alternatively, when evaluating the development timing decision, we must calculate NPV using a higher "timing-adjusted" discount rate, and develop the property only if its NPV using this timing-adjusted discount rate is greater than zero. This paper uses option pricing ideas to convert this development timing advice into a more concrete and user-friendly decision rule: develop the project when its "development-timing NPV" is positive, this development-timing NPV being calculated using the normal discount rate.

Jan 1, 1997

By B. W. Madsen

Experimental results obtained from large scale (7 tons), long-term (500 days) leaching of low tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when minus ½ inch ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from plus ½ inch ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Predictions of copper recovery from an ore sample which included the minus ½ -inch fine fraction and leaching for 460 days was 56.5 percent, and the recovery from leaching was 47.0 percent. The presence of fines caused channeling and uneven solution distribution and inhibited the leaching rate.

Jan 1, 1974

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By Robert M. Cox

Surface mining of coal in the South developed into a major industry during the 1960's. The economic significance of the industry is much greater than is readily apparent when one considers only the value of the coal mined. The abun-dant supply of relatively inexpensive steam coal for electric power generation that has been derived from the surface mines has provided the foundation for the industrial expansion that has occurred throughout the South. The region, in gen-eral, has enjoyed the benefits of plentiful low cost electric power. However, re-cent political decisions, at all levels of government, threaten to destroy or severely curtail the surface mining of coal and eliminate the economic advantages once enjoyed by the region. These political decisions are rapidly changing the basic rules of operation and fundamental economics of surface coal mining. Recent changes, resulting from the enactment of environmental and health and safety laws and various bureaucratic rules and regulations, have had a three-fold effect: 1) Greatly increased operating cost, 2) increased lead times for mine development, 3) limited potential reserve base for future mining. Also current legislative proposals are casting a shadow of uncertainty over the future of all coal mining operations that has created serious delays and in-creased cost for the expansion of the coal industry necessary to meet our project independence goals. Technology Surface mining is the safest and most economical way to produce raw materials from the earth's crust. It also affords a more healthier working environment for the individual miner. Surface coal mining now accounts for more than 60 percent of the annual coal production in the South. Surface mining of coal requires the removal of the overburden to expose the

Jan 1, 1977

By Thomas B. Faddies

The Trixie mine is located in the East Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1983

By John Duff Erickson

Determination of the final pit limits of an open pit copper mine is a problem that has far reaching effects on the life, profitability and operation of a mine. The solution to this problem requires that all of the significant variables affecting the final pit limits be considered together with corporate objectives as the guiding principle. This paper discusses the use of these variables and how they should be applied to plan the future of a mine. The objectives of a final pit plan; are determination of the extent and location of ore reserves, the allowable stripping to be accomplished to uncover the ore, the final pit surface intercept, final pit topography and the contained metal values in both ore and waste. The objectives of the plan must be consistent with corporate objectives as they pertain to profit, future investment in the mine, return on investment, alternative investments, conservation and perpetuation of the corporate entity. The subject will be treated in three parts: economic considerations, effect of leaching and pit design technique. At the outset, it is assumed; that the extent of and metal values in the mineralized area to be considered have been reasonably defined by development drilling and sampling.

Jan 1, 1968

By P. F. Mataich

When the subject of plant computers is brought up most people visualize the computer's controlling the entire plant with very little operator intervention. Actually, this picture is true today in only a limited number of cases and will certainly not be true in the minerals industries for many years to come. There are several ways in which a plant computer can significantly contribute to improving plant operation and closed loop control is only one of these. First of all, what are the basic ingredients for good plant control? For good plant control, two requirements must be met. First, the operator must get good information feedback from the process and then he must know what action to take in response to this information. Control information can be obtained through instruments, laboratory analyses, or through simple visual observation. If it is timely and accurate and the operator knows how to use it, then we have the makings of a good plant control system. The computer can be of help in both these areas by getting good data back to the operator and in helping to develop a good control scheme for the plant.

Jan 1, 1966

By Paul L. Bearden

The accumulation, handling, and utilization of sludges formed from wet process phosphoric acid is one of the major problems in the industry. The purpose of this paper is to explain some of the considerations and techniques that can be employed to provide some measure of control over the problem. An acid made from a Central Florida phosphate rock is used to illustrate the effects of one process design approach used to provide one type of control. Other approaches or techniques are discussed on a general basis. In every case, the discussion is purposely limited to conventional dihydrate processing in which phosphoric acid is produced from the filter at a strength of approximately 30% P205 and is subsequently concentrated to higher strengths such as 44 and 54% P205.

Jan 1, 1966

By T. S. McGahey

The southeastern region of the United States has long been a major market area for coarse and medium particle size natural ground calcium carbonate fillers. The primary market for calcium carbonate in the southeast traditionally has been as fillers in building materials such as carpeting, joint cement and roof shingles. In these applications the economic value of the calcium carbonate in the final product is weighted more toward lessening the cost of the final product, as opposed to contributing any desirable physical characteristics. For example, in carpet backing applications the calcium carbonate filler does little more from a physical standpoint than add weight and body to the backing adhesive. The important factor in the use of calcium carbonate in carpet backing is that it can be used at high loading levels to replace the more expensive latex binder, thus lessening the cost of the final product. It is estimated that calcium carbonate producers in the southeast sell in excess of 200,000 tons (181,436,000 kg) annually for use in latex compounds for carpet backing applications.

Jan 1, 1986

By Theodore M. Olson

The Washington State Highway Department consists of seven geographic dis¬tricts. District offices are located in Seattle, Wenatchee, Olympia, Vancouver, Yakima, Spokane and Bellevue. District is covered from the Spokane office, and is responsible for the six counties in the northeast corner of the state (Fig.l). It is bordered on the north by the International Boundary, on the south by the Snake River, on the east by the Washington - Idaho border, and on the west by a north-south line thru Lake Roosevelt. The landslides to be discussed in this paper are at Colfax, Washington, which is located in the southeast corner of the district. The town of Colfax is situated in a narrow valley eroded into the Tertiary volcanic basalts by the Delouse River. The valley walls are steep and generally colluvium mantled. State Highway 1°c, from Spokane to Colfax, descends into the valley from just north of Colfax on a bench cut into the valley wall. The highway department designed a widening project to increase the misting two lane roadway to three lanes, thus providing a passing lane for uphill traffic. The third lane was constructed as a cut section for the entire length. Construction excavation was begun at the top of the hill in silts of eolian origin. Proceeding downhill, excavation encountered three individual basalt flows with two zones of palagonite tuff separating them. The upper palagonite zone was dry, and excavation proceeded across this zone with no mishaps. The lower palagonite zone carried considerable groundwater. As excavation crossed the lower zone landsliding became contemporaneous with excavation, due to removal of toe of slope and saturated conditions. Remedial measures for landsliding consisted of designing shot rock buttresses across the palagonite zone and also the installation of horizontal drains to reduce hydrostatic pressure.

Jan 1, 1971

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962