Search Documents

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By Ignazio Carbone

"During the design of a typical modern subway, engineering aspects prevail since underground structures remain hidden to most humans. Aligning the advanced architectural concepts with the engineering requirements of the Naples Metro Line 1 (Italy) called for a thorough rethinking of the design process so that the engineering could be kept aligned with the architecture, integrating seamlessly the two with the construction methods, standards and technology.The preliminary design process consisted of three major phases: •,geotechnical and geological issues, preselection of construction methods; •,functional scenario based on engineering and construction requirements; •,review and merging of the architectural concept with the functional and engineering aspects. The last phase proved the most demanding one, matching the first outline sketches with the applicable construction methods. This required continuous alignment of approaches, eventually leading to the design consistent with the original architectural vision, yet fully compliant with the engineering and construction framework. At the beginning general information on Line 1 will be provided, followed by some main features of the construction work along the Dante – Garibaldi section both for the tunnel and the stations. At the end, the selected methodology and the related consequences on the functional, technical and architectural design will be outlined.City of Naples current municipal transportation plan envisages a circle ring line for the metro line M1. Actually it’s open to public the segment Piscinola – Dante – Garibaldi run by AMM, municipal company. This ring segment has been built by Metropolitana di Napoli, while Napoli Metro Engineering (company belonging to MMspa Group) is in charge for the planning of entire system and construction management. Line 1 connects Piscinola-Secondigliano northern periphery to Vomero shopping neighborhood, downtown and Central Railway Station."

Jan 1, 2016

By I. Yu. Melekestseva

Two types of hydrothermal massive sulfide fields were discovered in the Mid-Atlantic ridge (MAR) in the last twenty years. The first type associates with basalts and includes the TAG, Snakepit, Broken Spur, Lucky Strike and Krasnov hydrothermal fields. The second type is related to ultramafic rocks and represented by the Logatchev, Rainbow and Ashadze hydrothermal fields. In 2007 a new, probably, the largest cluster of hydrothermal massive sulfide field on the MAR (Fig. 1), related both to basaltic and ultramafic rocks, was discovered at 13°31'N of the MAR (Beltenev et al., 2007). [ ]

Jan 1, 2008

By R. A. Matuszak

U.S. Government sponsored studies proclaim large reductions in surface mine productivity. Consulting studies place a large share of the blame on increased governmental regulatory activities and on inexperienced, improperly train people. Union rules, which allow indescriminate bidding for job openings, seem to be a major factor causing the lack of experience in spite of elaborate training programs.

Jan 1, 1982

By D. J. Frey

While costs of most commodities and services have increased markedly over the past 25 years, the cost of electricity has steadily declined. One of the reasons for this price decline is the improved efficiencies of generating plants which is shown in Fig. 1. 1,2 Another reason for this is the decline in coal production costs. Efficiencies for the best plant increased from about 32 percent in 1540 to about 40 percent in 1962 and then decreased slightly to 38 percent in 1965. The increase in efficiency for all plants (US average) has been even more notable, progressing from less than 15 percent in 1940 to about 32 percent in 1965. The chief reason for the improved efficiency is the change in operating steam temperatures. These increased about 12 F per year until 1200 F was reached in 1962. At this high temperature excessive corrosion of super-heater and reheater tubes was experienced and steam temperatures were dropped back to 1050 F and even 1000 F in some cases. To successfully compete against other energy sources for generating electricity, this corrosion problem must be solved so that operation at higher temperatures and thus, increased efficiencies will be possible.

Jan 1, 1967

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

Coal has traditionally been an integral part of life in Kentucky. Coal mining produces a large part of revenue for the Commonwealth of Kentucky and provides a significant number of jobs to the residents of eastern (less in western) Kentucky. Recently, however, the coal industry of Kentucky has had to endure many hardships. The Clean Air Act set forth sulfur dioxide emission standards which have severely affected much of the coal mining industry in Kentucky, because much of the coal mined in Kentucky has a high sulfur content. In this paper, the background around the effects of Clean Air Act on the coal industry is introduced. The economic and social effects of the Clean Air Act on the Kentucky coal mining are addressed.

Jan 1, 1993

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989

By L. S. Gertsch, M. Z. Abu Bakar

The research presented here is part of a project to quantify the differences in the mechanical excavatability of rocks in dry and water-saturated conditions. A series of full-scale laboratory linear rock cutting tests were carried out with a long-bladed single disc cutter on dry and water-saturated sandstone blocks. The muck collected from the cutting tests was analyzed to establish a link with the specific energy (SE) of the operation. The coarseness index (CI), a non-dimensional parameter, was found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n was observed between SE and CI. The power n of the relationship for both dry and saturated rock was much lower than found in previous studies. The exponent n is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI was lower for saturated rock than for dry rock, at the same time, saturated rock cutting was found to be less energy-intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate, discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By W. G. Prast

Investments in fuel minerals and non-fuel minerals by petroleum companies are not a new phenomena. During the past 25 years, oil firms have entered mining via the acquisition route as well as by the direct development of grassroots mines. In the early 1980s, the "merger mania" in the natural resource industries came to a head. Oil company takeovers of mining firms, as well as other mergers between oil producers, captured headlines repeatedly, and speculation ran wild as to who would next acquire whom. Table 1 summarizes leading mining company mergers in the past two decades. There are some special features to the latest round of minerals investments undertaken by oil companies. First, direct takeovers of mining companies have become the preferred means of entry into minerals, with entry from scratch being relegated to the sidelines. This was not always the case. While there are instances of oil firms buying coal and copper companies dating back to the 1950s and 1960s, most of the early minerals work by petroleum firms was from internally generated projects. When the oil companies first became involved in uranium, for example, the uranium mining industry was in its infancy. There was not much market structure to buy, and it was relatively easy for everyone to get into uranium on the ground floor.

Jan 1, 1983

By W. A. Zingg

Impervious zones in copper waste heaps create a problem in contacting the rock with leaching solutions. These zones are normally associated with compacted layers .formed on the surface of each lift by dump truck traffic and by disintegration of the rock exposed to atmospheric conditions. These layers are usually only a few feet in depth--but, nevertheless, act as barriers to vertical flow causing the leach solution to perch in the heap, Consequently, much of the rock remains untouched and the leach solution breaks out the side of the heap instead of continuing downward to bedrock. One solution to this problem is breaking the hard pans with explosive charges. However, to use explosives means adopting new explosive materials and methods. To use this process successfully requires finding answers to operating conditions inherent to waste heaps. Foremost among these are: (1) type and size of casing that can be used because of limitations brought about by drilling problems, caving and, corrosive conditions; (2) perforating the casing at required levels; (3) an explosive capable of being pumped; (4) obtaining detonation of the, main charges through, the wail of the casing; (5) an explosive with the ability to propagate through the voids of the rubble and one which is not affected by water, acidic solutions, or back pressure conditions from hydrostatic heads; (6) to heave and rupture the compacted zones without chambering or recompressing the waste material.

Jan 1, 1970

By S. K. Palm

Volatility is a fact of life in the mining industry. Prices of and demand for mineral products are among the most volatile of those for any product. The volatility of these markets wreaks havoc on both corporate management and the personal lives of mining people. Yet, until recently, it has been difficult to assess the impact of volatility on business strategy. This paper discusses how mining firms can profit from market volatility through an operations strategy that stresses operating flexibility. The foundation for our strategy analysis is the observation that a mine is analogous to a stock option. Techniques based on those developed to value stock options have recently been extended to the field of mine valuation. The insights provided by option pricing are very valuable in the development of mine operating strategy.

Jan 1, 1986

By Paul R. Thomas

This paper addresses the long-term cost and availability of primary gold production from the Republic of South Africa. Forty-four major producing or developing operations were evaluated. The analyses present estimates concerning 1) total refined gold potentially available from demonstrated resources, 2) annual production potential into the next century, 3) long-term weighted average total costs for underground mine production and surface waste reprocessing, 4) the expected annual decrease in gold production, and 5) the ability of other market economy countries to compensate for the anticipated decline in South African gold output. This paper draws upon the data and analyses of a recent Bureau of Mines, U.S. Department of the Interior, Minerals Availability Program appraisal that evaluated the worldwide availability of gold and silver from primary precious metal operations and as a byproduct of base metal production.

Jan 1, 1984

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By Alvin Kaufman

Malthus, an eighteenth century economist, predicted a rather dismal future for the world. It was his contention food supplies would not be sufficient for the population of the world because the economy of a nation grew arithmetically while population increased geometrically. As a consequence, within a relatively few years mass famine would spread throughout the world. This prophecy, based on an agrarian economic situation, did not come true at least insofar as the Western World was concerned. In largo measure, the salvation of our part of the earth resulted from the growth engendered by the Industrial Revolution. Throughout much of today's world, however, the Malthusian theory seems to be coming true. The advantages and benefits of the Industrial Revolution have net reached all nations. Further, the situation has been compounded by the benefits of modern medicine. This has reduced child mortality and extended life expectancy, but placed no limitations on births in the developed countries, child mortality has declined to 2 percent and adult life expectancy has doubled, but education and general prosperity have resulted in voluntary limitations on pregnancies thus partly offsetting the increased chance of survivals Even so, the present rate of population increase in Europe is approximately 6 percent per decade, and somewhat higher in the U.S., Japan, and other developed countries. The world as a whole, however, is expected to double its population by the year 2000, This would imply a rate of increase in the less developed countries approximately four times that in Europe.

Jan 1, 1966

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999