Search Documents

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

From some of the largest tunnel projects in the some of the most vibrant cities, to smaller projects in remote corners of the globe, the Robbins Co. announced two tunneling projects in which its tunnel boring machines will be used. Robbins earth pressure balance (EPB) machines undercut Downtown Zhengzhou. Zhengzhou, a city of 7 million people, is set to become a crossroads for rail commerce in China. The country?s future main routes, traveling between Beijing and Guangzhou (North-South), and between Xuzhou and Lanzhou (East-West), will intersect in the city. The plan includes up to four rail lines in Zhengzhou itself, which will eventually link up to the national lines. Excavation of Zhengzhou Metro?s new Line 1 tunnels began on Sept. 28, 2010, when the first of two 6.3-m (20.7-ft) diameter Robbins earth pressure balance (EPB) machines was launched from a 16-m- (52-ft-) deep shaft.

Jan 1, 2010

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By Nicola Della Valle

The Singapore Land Transport Authority (LTA) is currently expanding capacity by extending their Metro system from South of the city to the North East end of the island. The scope of Contract 704 involved excavating a long reach of tunnel which had a complex rock/soil interface comprised of fresh granite overlaid by clayey sand. Two 6.5 m diameter Earth Pressure Balance (EPB) TBM’s were used to bore the tunnels. These machines were designed so that both hard and soft rock could be excavated. The cutter head was equipped with a combination of both rippers and disk cutters. Soil conditioning was achieved by delivering foam through a multiple port injection system. This very irregular profile of the interfaces posed many challenges to the equipment and the people.

Jan 1, 2001

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By Y. Topkaya, R. E. Johnson, B. R. Palmer, Jia-Jun Ke, Da-Ping Kang

The kinetics of the leaching of antimony oxide ore (Sb2O4) in aqueous hydrochloric acid solutions has been investigated. This dissolution reaction is a heterogeneous solid-liquid reaction. It has been found that the leaching temperature and the concentration of hydrochloric acid turn out to be the significant influencing factors on the leaching rate. The apparent activation energy for the leaching reaction was determined to be 63.5 W/mol within the experimental temperature region of 50O to 90O C. The experimental results indicate that the leaching process is controlled by the rate of the chemical reaction.

Jan 1, 1993

By Guy T. McBride

Mr. Chairman, Fellow Keynoters, Ladies, and Gentlemen: It is purposed to consider the theme of this meeting, "The 1970's - Pivotal Decade for the Mineral Industries," from the particular -- some would say peculiar -- point of view of one engaged in mineral engineering education, and this coign of vantage prompts the textbookish subtitle, "Problems and Solutions (?) in Undergraduate Mineral Engineering Education." Three interrelated problems, or problem areas, will be presented and discussed, and where solutions seem to be emerging or seem worthy to be suggested, they will be identified. The three problems are: 1. The goals, and therefore the course requirements, of the undergraduate curricula are in question, 2. The unit costs of undergraduate education appear excessive to those who bear the charges, and 3. The social ambience of the day affects for the worse the work attitudes and the career motivation of both prospective and in-course students. The Need. - Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development, and production levels, Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of our society and profession. The latter reference is, of course, to the current work of the National Commission on Materials Policy (U.S.A.) under the executive directorship of Dr. James Boyd. Predating this, and perhaps to some extent

Jan 1, 1972

By J. J. Poveromo

"Iron ore for alternate iron processes concerns alternate iron products designed for use in EAF (electric arc furnace) steelmaking processes. These alternate iron products include both DRI (direct reduced iron), HBI (hot briquetted iron) and merchant pig iron. Merchant pig iron can be produced in conventional blast furnaces, mini blast furnaces (including charcoal BF's) or novel processes such as RHF/SAF (rotary hearth furnace/submerged arc furnace) such as Iron Dynamics or RHF such as Mesabi Nugget. These novel processes are coal based and can use iron ore concentrates or recycled steel plant oxides. The blast furnace processes can use conventional feed materials: pellets, sinter, lump ore and coke. However, DRI and HBI processes are predominantly pellet based but require DR grade pellets that are low enough in acidic gangue (SiO2 and Al2O3) to avoid additional expense in the EAF process This paper will focus on the quality and availability of DR grade pellets for NAFTA DRI/HBI plants but also concentrates for fines based processes and feed materials for merchant pig iron production. INTRODUCTION This paper will outline alternative (to the blast furnace) competitive ironmaking processes and process routes. Within each section the types of iron ore to be utilized will be discussed. Before discussing some of the details of these processes, it may be appropriate to review some definitions and commonly used terms within this industry. DefinitionsDirect Reduction: Reduce iron oxide to metallic iron without melting. Unreduced ore compounds remain as undesirable oxides • Direct Reduced Iron: Iron oxide feedstock exits in same form as entered (pellets in, pellets out; lumps in, lumps out) • Hot Briquetted Iron: DRI that has been hot (1200°F, 650°C) briquetted to a high density pillow shaped briquette • Hot Metal: Molten iron in liquid form, above 2500°F, 1370°C • Pig Iron: Solid product of the iron blast furnace • Residuals: Undesirable elements such as copper, nickel, chromium, tin, sulfur, molybdenum and phosphorus • Gangue: Rock minerals in the iron ore such as silica (SiO2), alumina (A2O3), calcia (CaO), magnesia (MgO). These remain in the oxide form in DR processes. • Reduction: Fe2O3 + 3 CO = 2 Fe + 3CO2 2 Fe2O3 + 3 H2 = 2 Fe + 3H2O (Fe2O3 > Fe3O4 > FeO > Fe)"

Jan 1, 2018

By S. Middlemiss

The Indentation Fracture technique is being developed as a tool for use in comminution and mineral liberation analysis. Fracture toughness measurements for a number of mineralogical materials were made and comparisons were drawn between these and properties measured with the Ultrafast Load Cell drop weight apparatus. The technique has also been used as a probe to quantify differences in fracture properties at different areas in the microstructure of a material. In both a Utah limestone and a South African quartzite, material near a grain boundary fractures very differently to that in the bulk. Ongoing work is ultimately aimed at producing a comprehensive fracture model for a multi-mineral system based on its micro-fracture characteristics.

Jan 1, 1994

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By L. Alagha, O. Molatlhegi, S. Khatibi

"In the present study, the effect of organic/inorganic (hybrid) polyacrylamide polymer on fine coal flotation was investigated. Raw coal samples contain about 37% of ash-forming mineral at a feed size of -75 + 38 um were subjected to flotation tests in the presence of in-house synthesized hybrid Al(OH)3-PAM at different polymer dosages and pH values. Results show a significant improvement in both combustible recovery and ash rejection at 1 ppm polymer dosage. Further improvement of combustible recovery was obtained when flotation was performed at pH 5. Interfacial properties of coal particles before and after flotation were examined through electrokinetic (zeta potential) measurements of coal/water slurries. Zeta potential vs. pH curve were established and compared. In the case of raw coal/water slurry, zeta potential-pH curve resembles the ash-forming minerals (silica and clays) more than coal. After Al(OH)3-PAM-assisted flotation, the zeta potential of froth/water slurry shifted to more positive values point which strongly indicates significant removal of ash-forming minerals from coal by Al(OH)3-PAM. INTRODUCTION Coal has been a major commodity in meeting the world energy demand during the past several decades (Milici et al., 2013). According to the international energy agency, global coal demand will continue to increase for the coming decades. With increasing world population, the global electricity demand would also increase as more people would get access to basic electricity especially in developing countries (Maggio & Cacciola, 2012). Due to this increase in energy consumption, operations in coal mining and beneficiation processes have been highly mechanized to meet the demands. This mechanization has increased the quantity of raw fine coal particles produced which contain high amount of ash-forming mineral matter (slimes). Aplan et al., have reported that the major constituents of ash-forming minerals in U.S.A coal are clay minerals such as kaolinite, montmorillonite and illite (Aplan, 1997). Conventional froth flotation for fine coal cleaning suffers mainly from two major problems: 1) Low recovery of ultrafine coal particles due to slime coating by ash-forming minerals, and 2) The lack of selectivity, which results in the flotation of middlings and entrainment of mineral fines in the froth (Polat et al., 2003). Slime coating on both valuable and air bubbles have been proposed to explain the observed reduction in flotation recovery especially when fine grinding is required. In this case mineral matter may be degraded to extremely fine or colloidal sizes thereby creating difficulty in the water clarification process such as flotation. Slimes inhibit bubble-particle attachment, and increases reagent consumption due to the increase in solid/liquid interfacial area, resulting in low coal recovery."

Jan 1, 2015

By Rodrigo Peroni, Euler Victoria

Knowing the depth of contacts between weathering zones in phosphate mines is determinant to define the stripping ratios and the mineralized zones. Contacts are gradational and difficult to define even in the drillhole samples, so the combination with geostatistical simulation techniques helps to define the contact zone and the grade distribution, providing a way to assess the probability of the occurrence and the positioning of contacts between the barren waste and the ore zones. These inputs are used in the scheduling, anticipating risks associated with mine planning scenarios. The results from an application to a case study showed a good improvement when compared to traditional techniques.

Jun 25, 2023

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

In the screening process, used to prepare particles for many applications, shape is known to have a significant effect. The degree of flakiness of construction aggregates has been considered particularly important. The objective of this research was to find values of operating parameters that optimize the separation of flaky from non-flaky particles by slotted screens. Thus an investigation was conducted to experimentally determine the influence of the particle size and thickness on the screening process. The Response surface method was employed for modelling and analysis of the data. Experiments employing a central composite design were performed on a pilot-scale, rectangular-aperture, vibrating screen to examine the effects of the screening variables the mass recovery of flaky and non-flaky particles to the oversize product. The SAS statistics package was used to fit a second-order model to each response and to analyze the fitted surface to determine the optimum levels. The optimization associated with a dual response system was then considered. The results of this study should provide a basis for optimizing screening conditions to obtain maximum recovery of non-flaky particles to the screen oversize while minimizing the recovery of flaky particles, which should be of interest to the aggregate industries.

Jan 1, 1999

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By Gordon T. Clark, Stephen H. Gleaton

This paper discusses the conceptual design of cut-and-cover tunnels currently being considered as one of the replacement options for the earthquake damaged, elevated double-deck highway and seawall built in downtown Seattle 50 years ago. The 4.8 km (3 mile) long, 6-lane improvement consists of 1.6 km (1 mile) of at-grade roadway with aerial interchanges, 1.6 km (1 mile) of large two-level cut-and-cover tunnels along the Elliott Bay waterfront, and retrofit of the 50-year old, 1.6 km (1 mile)long Battery Street tunnel and north transition to grade. Construction of deep cut-and-cover tunnels, in complex glacial geology overlain by hydraulically placed fill immediately adjacent the existing sea wall, will require extensive use of concrete diaphragm walls, ground improvement and dewatering. The potential liquefaction and lateral spreading of the fill materials in this active seismic region pose significant design challenges and risk.

Jan 1, 2003

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By R. S. Austin

One third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. . Its whiteness, brightness, fine particle size, platelet shape, surface chemistry, and chemical composition make kaolin an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978