Search Documents

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By Richard S. Kunter

The Bulldog CIP plant treats the slime portion of current tailings and reclaimed flotation tailings from the adjoining 350 tpd (3.67 kg/s) silver-lead flotation mill. Changes to the dredge reclaimer, pulp storage tank and trash removal system have allowed an increase in tonnage treated to a sustained 460tpd (4.83kg/s). CIP feed is 3-4 oz/T Ag (102.9-137.1 ppm). Following conventional cyanidation, carbon is added to the slurry. Silver loaded carbon is stripped in atmospheric-pressure vessels using hot caustic cyanide. Silver recovery from this solution is by Zadra- type cells. Some of the modifications to the plant and operating techniques are discussed.

Jan 1, 1981

By Jesse H. Auvil

In January of 1966, during the annual session of Georgia's General Assembly, Representative Paul E. Nessmith of Statesboro, Georgia, walked into my office and asked me what I thought of the advisability and feasibility of a law which would require the mining operators to reclaim their mined out lands. My answer to him was, as a one time mine superintendent and operator, that I probably would not think very highly of the added cost which reclamation would impose on the operation; but that since assuming the job of Chief Geologist and Assistant Director of the Georgia Department of Mines, Mining and Geology, and in retrospect, I could recommend it very highly, particularly in view of the increased pressure being applied by the Federal government along these lines. I stated then and still emphatically state that this sort of administration should be done on the State level rather than the Federal level. He asked me if I would conduct him on a tour through some of the mining country in which I had worked and to this I readily agreed. The result of this trip was that he was adversely impressed by the devastation which the mining operations had wreaked on that area of middle Georgia along the fall line known as the kaolin belt. Very little except talk was done for the remainder of 1966.

Jan 1, 1970

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By D. J. Beeby

California's Surface Mining and Reclamation Act (SMARA) was passed in 1975 to identify and protect mineral resources in areas of high land-use conflict and ensure reclamation of mined lands. Under SMARA, aggregate resource availability is quantified and compared to forecasted demand in specific market regions. Fifteen regions studied thus far cover 20,000 square miles and contain 50 billion tons of high-quality aggregate resources which have been legally designated as ?regionally significant?, providing a measure of protection previously unavailable. SMARA reports and State testimony at local hearings have supplied objective information and helped reduce conflict in mine-permitting decisions.

Jan 1, 1987

By Elena Chiriotti, Federico Valdemarin, Jan Cenek

"SUMMARY The “28 May Station” is the only transfer station between the existing Green and Red metro lines in Baku. As part of the huge development strategy of the metro network, the complete separation of the existing underground lines has been planned at this location, in order to simplify the operation of the future metro system. The extreme challenge of the project is represented by the need of achieve the separation of such lines over a breakdown of the operation of just five weeks. The lack of direct access from the surface, a complex geology with artesian water layers, a congested underground space and sensible buildings represent additional constraints. The chosen design solution consists in creating a complex steel pipe jacking frame around the operating tunnels and then excavating under such frame two large caverns where the separation of the existing lines and the construction of the new metro tunnels will be achieved. Soil treatments have been conceived to mitigate the geotechnical risks and to reduce possible impacts on the existing structures. The paper illustrate the challenges of this extraordinary project, one of the most complex underground structures under study, the design solutions and the risk management approach used to manage the complexity and to design the mitigations measures. INTRODUCTION The metro network in the capital of Azerbaijan is rapidly growing together with its metropolitan area. The beginnings of the existing metro system started in Baku in 1967 in Soviet times. To date, only two lines (Green and Red) are in operation with a total length of 34 km, including 23 stations. The future network will be much wider: besides the construction of three completely new lines and the extension of two existing lines, the whole metro project includes the development and modernization of the existing metro sections. A consortium formed by Systra (leader), Mott MacDonald (Praha) and Saman (Korea) awarded the contract for the preliminary and detailed design of infrastructures for the extension of Baku Metro Network. This extension consists in 83 km of new lines and extension of existing lines. As part of this modernization project, the connection of the Green Line at the 28 May / Cefer Cabbarli Stations, focus of this paper, represent also it’s ""Achilles' heel"" given that the already very congested system have only one transfer station."

Jan 1, 2016

By Eli Curiel, Ingar F. Walder, Patrizia P. Schuster, Walt Keyes

Mansfield Canyon, of the Wrightson Mining District, Santa Cruz County, Coronado National Forest, Arizona, was actively mined in the late 1800's and early 19001s, with minor activity until 1953. The main products were lead, silver, copper, zinc, and gold occurring in polymetallic quartz veins. The canyon contains numerous adits and waste dumps, some of which generate metal-loaded acid. Samples of seeps, waste dumps and bedrock have been collected for various analyses: metal concentrations, acid base accounting (ABA), and water quality to evaluate the extent of oxidation and metal release from the start of mining until present, the potential impact, and reclamation options. Although the waste-rock piles within the canyon are small (2,000-10,000 tons), they have a high sulfide content with little or no neutralizing capacity. It is planned, therefore, to move the waste piles either to a constructed repository site within the canyon or to a copper leach facility to be used as an acid generator.

Jan 1, 2000

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro, NC, treating crude Waelz oxide (WOX) to produce special high-grade zinc by a hydrometallurgical process comprising leaching, zinc solvent extraction/electrowinning, melting and casting and bleed treatment. Cadmium removal by zinc-dust cementation plays an essential role in the bleed treatment circuit to prevent cadmium buildup in the circuit. Silica, though present at a low level of approximately 0.3 percent in the WOX feed material, had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also affected. To identify the source of the silica issues, silica levels were mapped throughout the circuit, and adjustments, including using pregnant leach solution as the feed to cementation, and pH control in the WOX leaching and neutralization were introduced to mitigate the issues created by silica gel in the circuit. IntroductionLocated in Mooresboro, NC, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz oxide (WOX) to produce special high-grade (SHG) zinc. The flowsheet, known as the Modified Zincex process, consists of leaching, solvent extraction (SX), electrowinning (EW), melting and casting and bleed treatment (Fig. 1). Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press.At the refinery, WOX pulp is leached at a controlled pH to achieve the maximum zinc extraction, according to the main reaction:"

Jan 1, 2016

By Klein E., Kinscher J., Lizeur A., De Santis F., Lhoumaud E.

Seismic repeaters are rarely observed phenomena in underground mines. However, recent studies in Garpenberg mine (Sweden) have demonstrated that seismic repeaters and multiplets may represent significant portion of the total number of microseismic events (> 80 %) related to excavation operations. Detailed seismic analysis, involving template matching, multiplet clustering, double-difference relocation, source parameter and mechanism estimation, and interevent time analysis, suggest that seismic repeaters represent brittle frictional parts (asperity) of creeping, planar shaped, pre-exiting structures of several meters length. It is furthermore suggested that seismic repeater occur preferentially in weak rock-mass materials (e.g. talc) associated with strengthening friction behaviors. These results may imply that postblast related stress redistribution may be governed by “silent” aseismic movements in preferentially weak rock mass materials, what questions the reliability and performance of seismic monitoring to survey stress evolution during excavation operations. However, once the seismic and aseismic coupling processes and the geological nature linked to repeater occurrences are better understood, their detailed monitoring bears also opportunities to survey and quantify aseismic post-blast stress transfer. Here we present ongoing investigations on repeater occurrences aiming at better understating on their geological and geomechanical origin. Furthermore, we try to develop advanced monitoring tools helping to quantify aseismic slip and to provide criteria for seismic hazard as asperity density and the related potential to generate larger dynamic rupture zones. For this respect a local monitoring network has been set up close to certain repeater target families. Furthermore, geological well log drilling throughout repeater occurrences as well as geotechnical strain measurements (e.g. extensometer, optical fiber etc.) are currently conducted to provide crucial information on the geological nature of repeater and to quantify and characterize background creep induced from excavation.

Apr 26, 2022

By Adrian Smith, Debra W. Struhsacker

There is now overwhelming evidence that, despite concerns to the contrary, natural degradation of cyanide and cyanide attenuation by hydrogeochemical processes are capable of minimizing or eliminating potential water qua1ity impacts from heap leach systems. A1 though there was some recognition of these data by the regulatory authorities, for example the initial USEPA modification of cyanide standards to an advisory level, many states have codified standards inappropriate to the clearly site specific nature of heap leach operations. As an overview to this problem, this paper will integrate the theoretical chemical data on cyanide with the observed geochemical behavior of cyanide in the decommissioned heap leach environment. The cyanide species that are likely to exist within an abandoned heap leach system will be identified, and the relative toxicity and potential environment effect of these cyanide species will be discussed. These data will then be used to evaluate cyanide detoxification regulations for decommissioned heap leach projects in 14 states.

Jan 1, 1987

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By Michael Rehbock-Sander, Romed Insam

"INTRODUCTIONThe idea of building a summit tunnel under the Brenner occurred to the Italian engineer Giovanni Qualizza as far back as 1847. But it was to be another 160 years to pass before a base tunnel was to be built.In 1971 the idea of a tunnel at the Brenner was dusted off again. The UIC, the International Union of Railways, commissioned a study for a new Brenner railway with a base tunnel. By 1989 three feasibility studies had been drawn up which formed the basis for further planning of the Brenner Base Tunnel.This was the start of the planning activities. In 1994, the European Union included the Berlin-Naples corridor in the list of priority projects. Ten years later, Austria and Italy signed a State Treaty to build the Brenner Base Tunnel. In that same year, what is today the BBT SE was established.PROJECT DESCRIPTIONThe Brenner Base Tunnel (BBT) with a length of 55 km is the centrepiece of the Helsinki-Valletta Transeuropean Traffic Corridor from Finland to Southern Italy. The BBT tunnel system connects in the north with the Innsbruck station (Austria) as well as to the feeder routes in the Lower Inn Valley, and opens to the south with the projected new line in the direction of Verona (Italy). The tangible design efforts have been underway since 1999; the start of construction of the first section was in the year 2007. The project is financed by the Italian and Austrian governments (each 30 %), as well as by the European Union (40 %).From 2027 onwards the Brenner base tunnel, including the existing lines connected with it, will carry a daily average of 330 trains (approx. 80% cargo trains and 20% passenger trains)."

Jan 1, 2016

By M. D. Carter

The availability of environmentally acceptable and reliable energy sources is an important issue for Federal, State, and local planners. A cooperative program by the U.S. Geological Survey, State geological surveys, and the U.S. Bureau of Mines has developed a national GIS-based systematic effort to collect, analyze, and depict data characterizing the relationship between restrictions to mining and the potential development of the Nation's coal resources. Land use/environmental and technologic/geologic restrictions are identified within selected 1:24,000-scale, 130-to 150-sq-km 7.5-min quadrangles and applied as overlays to maps of coal-bed thickness, depth, and mined-out areas. Tonnages of original, mined and lost-in-mining, remaining, restricted, and available resources are calculated. Resultant data files are transferred to the Bureau of Mines for recoverability and cost analysis.

Jan 1, 1995

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By D. Kang

The adsorption behavior of silver in ammoniacal solutions on to activated carbon has been studied. The parameters affecting the adsorption of silver on to activated carbon included temperature, agitation speed, concentration of cations and anions as well as that of ammonia. It was found that the adsorption of silver from ammoniacal solutions was dependent upon the initial silver concentration in the solution and other factors. The recovery of silver from ammoniacal solutions was found to be not so effective as the case with gold reported earlier. The adsorption rate was relatively slow overall, despite a rather fast initial adsorption. The apparent activation energy for the adsorption was measured to be 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1998