Search Documents

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

In parallel work, the cyanide/silver impregnated activated carbon system was studied for the purpose of developing an alternate cyanide removal system. It was found that free cyanide can be reduced from 20 ppm to below 10 ppb with a fixed bed of silver impregnated activated carbon, since such cyanide removal might be applicable to gold mill effluents, the investigation was extended to the cyanide/gold impregnated activated carbon (GIAC) system. Batch tests were conducted varying the gold content of activated carbon, carbon/CN ratio, stirring speed, pH of the initial solution, and the reaction temperature. The adsorption isotherm of cyanide/gold impregnated activated carbon system was also studied. The results of these batch tests show that the behaviour of the cyanide/GIAC system is very similar to the cyanide/silver impregnated activated carbon system variation of the gold content of the impregnated activated carbon has some influence on the cyanide adsorption rate. The latter is mainly increased, however, by increasing the GIAC/CN ratio. The activation energy was determined to be 3.12 kca1/mole (13.08 kj/mole) and the Au(CN)2 saturation at 194 µ M/g NORIT ROX O.B. The experimental results of reaction temperature and stirring speed show that the adsorption of free cyanide on such activated carbon is controlled by pore diffusion inside the activated carbon particle or by surface reaction. The adsorption isotherm follows the linear model and it is favourable for the cyanide/gold impregnated activated carbon system.

Jan 1, 1994

By Peter N. Yanker

The two types of dryers used in the drying of copper concentrates are the rotary dryer and the spray dryer. The rotary dryer has until recent history been the traditional drying method used, Although spray dryers have been used in the chemical field for many years it is only recently that they have been accepted for drying of copper concentrates. The comparison made here will apply in a narrower sense to the drying of copper concentrates as fed into the reverbatory furnaces of the Smelter. To compare a rotary dryer and a spray dryer, which are two totally different methods and pieces of equipment, it is best to view them as systems each made up of certain elements

Jan 1, 1976

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne's Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By S. Barkhoudarian, R. R. Gupta, R. F. Steinberg

A study of the feasibility of using acoustic signals to detect discontinuities ahead of excavation has shown that reflecting interfaces in a homogeneous rock can be easily identified. Moreover, discontinuity interfaces in a very complex field site (where the rock face was weathered, was full of jointed rocks, and had a destressed zone running along the mine walls) could be identified with a reasonable level of confidence, using a cross-correlation technique for signal processing. The results of this study go a long way toward proving the feasibility of the technique. However, further development work is needed to optimize an operating system in a hard rock environment where boring machines are used for excavation.

Jan 1, 1997

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By S. Makni, R. E. McIvor

Grate discharges historically outnumbered the overflow type of industrial wet ball mills. However, overflow discharge mills now strongly dominate. In order to understand their comparative advantages and disadvantages, Corem carried out a broad review of this topic. Where the data made it possible, the Functional Performance Equation was used to separate circuit classification from mill grinding effects. Batch tests were conducted in a torque-metered mill at different slurry levels. This paper presents the outcome of these investigations, which is a very strong case for the industry to once again consider grate discharges.

Feb 1, 2023

By R. J. Wahrer

In 1996, the Office of Surface Mining (OSM) and the U.S. Fish and Wildlife Service (FWS) completed an Endangered Species Act (ESA) programmatic Section 7 consultation. From the resultant Biological Opinion, it was found that coal mining operations conducted under federally approved state regulatory programs would not likely jeopardize the continuation of federally listed species nor result in the destruction or adverse modification of critical habitats. The requirements of the ESA and their integration into the SMCRA permitting process and the responsibilities of the regulatory agency, the FWS and the coal operator will be discussed. Guidance on the development of protection and enhancement plans will be provided and site-specific examples given.

Jan 1, 2003

By Barry J. Hansen

Mining can make two major contributions to the cleanup of the environment. The first of these is the extractive technology that has become highly developed as a result of centuries of development. Of equal impor­tance are the methodology of analysis and the development of engineering solutions that are the stock in trade of the mining industry. Despite the differences between the industries, the processes for the development of a mine and the cleanup of a hazardous waste site are similar. The characteristics that impact the ability to develop a suitable process for treating an ore body or correct­ing an environmental problem are those relat­ed to the distribution of the contaminant or metal in the host material.

Jan 1, 1991

By Dewey W. Marino

Conventional remote sensing applications for the exploration of natural resources has largely been the domain of low resolu­tion Earth orbiting systems such as Landsat™ which can sample a broad range of the spectrum. As the classic application of remote sensing, it has proven its worth through the discovery of numerous mineral deposits worldwide. Often this technique relies more on the spectral content of the imagery for narrowing potential sites on the ground, but often cannot reveal the detailed context of the observed response. As the dawn of the new era in remote sensing grows closer, high-resolution imagery is proving its worth for the definition of mineral potential and its cost sav­ing advantages for mine management.

Jan 1, 1998

By R. G. Reddy

Viscosities of Feo-SiO2 slags were calculated using the previously developed structural based model. An expression was derived using hole theory and the atomic pair model to relate the NO0 and temperature to the viscosity. The deduced equation n=4.9x10-9 T1/2 NO0 exp (E/RT) poise was successfully applied to predict the viscosity of FeO-SiO2 slags in the composition range of 0.1 < XSiO2 < 1 for several temperatures. The calculated data agrees well with the experimental viscosity data.

Jan 1, 1991

By V. Carabias-Hütter, A. J. Basu

The paper aims at promoting sustainability assessment and reporting into practice using a globally acceptable set of guidelines and a common framework for internal and external reporting at a project/site level. Indicators are used for measuring performance, and this paper addresses development and implementation of performance indicators for sustainability assessment and reporting at local as well as global levels. The selection of a proper set of indicators is a challenging task. The indicators selected should provide the expected information for making right decisions. Relevant and credible sustainability reporting supported by a consistent performance indicator system can be the starting point for benchmarking environmental and social performance for the natural resources sector.

Jan 1, 2004

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By C. J. Hunter

Prior to the commissioning of the Sansu Sulphide Treatment Plant (STP), Ashanti Goldfields&apos; treatment facilities were capable of producing some 700 000 ounces of gold per annum. Ore sources were underground refractory sulphides, surface oxides and old tailings dams. In order to increase the mines production to 1 million ounces per annum and to accommodate the change in ore sources as surface mining moved into fresh sulphides, a part of the strategy adopted was -the construction of a new sulphide treatment plant with a capacity to mill 2.2 million tonnes per annum and produce 400 000 ounces of gold. The STP has been designed, built and commissioned. and has been in operation since February 1994. The Plant boasts the world&apos;s largest Bio-oxidation facility which is capable of treating 790 tonnes of sulphide concentrate per day at a grade of 11.4% sulphur and is currently undergoing an expansion to increase its capacity to 1050 tonnes per day. The following sections describe the reasons for selecting the BioX® Process, the plant design, the commissioning experience and the plant performance to date.

Jan 1, 1996

By R. D. Irvine

Enhanced concern for protection of the environment and attendant actions by environmental regulatory authorities in support of this concern are influencing to varying degrees the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms. In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States.

Jan 1, 1995

By D. R. Nagaraj

There are few organic ligands that can adsorb effectively on noble metals, especially gold, in aqueous media. Ligands containing sulfur and nitrogen donors are known to be the most effective. Dithiophosphorous acids, for example, are known to adsorb on gold under certain conditions and these, along with xanthates, are used traditionally to recover gold values by flotation from ores. These compounds, however, are not necessarily selective for gold since most of the associated sulfide minerals are also floated. Monothiophosphorous acids, on the other hand, were recently discovered to float gold values selectively from sulfide-containing ores in a mildly alkaline medium; thus the dicresyl monothiophosphate is now used commercially in a gold flotation operation in the U.S.

Jan 1, 1991

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980