Search Documents

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

By S. Frimpong

Cable shovel requires continuous monitoring through excavation to achieve reliability, longevity and economic usage. The operating environment and the stress and deformation fields on the front-end assembly must continually be monitored to avoid random fatigue failure. In this paper, the authors advance frontiers of cable shovel reliability through real-time stress and deformation monitoring during excavation. Cable shovel boom stress and deformation analysis are developed using a combination of flexible and rigid body approach. A virtual prototype is developed to simulate the cable shovel excavation in oil sands and to examine the motion, stress and local deformation of the boom. A numerical example is used examine cable shovel boom durability using stress and deformation fields simulation. The results show that stress and deformation are large around the joint between the upper body and the boom. The simulation of the effect of material properties on boom deformation shows that the deformation is larger in hard formation than in soft formation. The study provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2006

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By W. P. Arnott

This paper presents real time photoacoustic measurements of diesel-soot black-carbon (BC or EC) and Dusttrak nephelometer total carbon (TC) concentrations in a Nevada gold mine. Comparisons with time-integrated filter-based measurements of EC and TC accomplished using the NIOSH 5040 method were found to be 50% smaller than the integrated real time measurements. This work was initiated primarily as a demonstration project for the usefulness of photoacoustic instruments in measuring BC in the mine environment. Real time black carbon measurements are very useful for determining miner exposure, for providing feedback in mine ventilation systems, and for quantifying machine specific emission rates to understand the operating conditions for specific machines that produce greatest black carbon concentrations. This paper reports real time measurements of DPM from a loaded and empty hauler as it is operated in a drift with a 12% grade. The photoacoustic instruments were demonstrated to be satisfactory for BC measurements in the mine environment.

Jan 1, 2009

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By P. Schilizzi, A. Jarosz, M. Karmis

This paper is concerned with subsidence prediction methods and in particular with two techniques, one based on profile functions and the other on influence functions. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. In more detail, the hyperbolic tangent profile function, as developed by VPI&SU from field data pertaining to the eastern U.S. coalfields, and an influence function method currently being adapted for the same region, are presented and discussed. The applicability, advantages and limitations of these techniques are examined and comparisons are presented with field measurements. Computer software developed for the application of these prediction methods, for two widely used personal computer systems, are also discussed and a number of examples are presented demonstrating the potential of such programs.

Jan 1, 1986

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man&apos;s house as it was mined. Then it may have been stockpiled at each man&apos;s place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today&apos;s highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada&apos;s mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986