Search Documents

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By Donald R. East

In the planning and design of mill tailing disposal facilities, the chemical and physical nature of the fine­grained material to be disposed of has to be fully understood in order to create an efficient and safe long­term storage facility. Disposal of tailing has become the single most important source of environmental impact for mining projects and the development of many promising ore bodies has been delayed or even stopped due to problems of facility siting and design under pressure of increasingly stringent regulatory require­ments.

Jan 1, 1992

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By M. E. Rossi

Reconciliation of long-term block model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term block model reserves against a grade control model (generally, a model based on blast holes or production data). in this paper called an FI factor for tonnages, grade, and ounces; and also it should be done comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (called an F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator such as kriging will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMU's to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. and therefore the grade-tonnage predictions based on blast holes also need to be assessed, considering both unplanned dilution and the errors of estimation of the grade control model. This paper will focus on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves, and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer, which will yield not one, but several possible minable reserves, and therefore a range of possible minable tonnages and grades per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation, planned and unplanned dilution. and carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The motivation for the approach is discussed through an example, as well as a description of the procedures and steps involved.

Jan 1, 1998

By Eric Lundgren

The mining paradigm is changing on the continent of Africa. Jessica Kogel?s closing statement from her September 2013 President?s Page (ME, September 2013, pp. 6) has never been more appropriate, ?Africa is shaping up to be the next mining powerhouse, and there is huge opportunity for local communities, national governments and private industry to work together to create a win-win situation for all.? Supporting this notion, attendance at numerous industry conferences around the world demonstrates the shift toward a more sustainable, more environmentally conscious extractive model. But questions remain: How effectively is the industry making this transition, and how willing are companies to learn from the experiences of others? The international development community, as we like to call ourselves, is going through a parallel shift. We are experiencing our own funding crisis; governments are not as flush with resources as they were pre-economic meltdown. But more importantly, after a half century of implementing development programs, we must admit that while some of our programs have been fantastically successful, too many still fail to achieve the goal of poverty alleviation for the world?s poorest. Moving forward, we are forced to recognize that achieving success in scale and sustainability is not always accomplished from our work alone. As the director of international programs for Africare, a nonprofit with more than 40 years of experience implementing community-based development programs in Africa, I can report that our organization is changing the way we think about successful development partnerships. Africare recognizes that for too long the mining sector and nonprofits have been at odds, choosing noncommunication as a ?solution? to the problem. Both sides now recognize that this standoff is outdated, and Africare, specifically, is ready to cross the proverbial line. We see the potential benefits of mining for local communities and, when done responsibly, the opportunity to properly manage Africa?s resource boom as a benefit to all. There are challenges in this conversation. Many mining professionals view nonprofits as whistle-blowers, ready in a pinch to speak to news sources and complain about poor operational standards. Those are advocacy organizations, and while their role is important, they are not the only nonprofits interested in mining operations in developing countries. Organizations like Africare, with decades of experience implementing poverty reduction programs, approach this differently. We know we can work with mining companies to promote economic opportunity in the communities where mining operations are occurring. We recognize that the conversation is difficult, and we are open to discussions about how we can bring our unique experience to bear on the problems faced by mining companies in carrying out their investment programs.

Jan 1, 2014

By C. B. Manula

Languages such as SIMSCRIPT and GASP have reduced the programming skills required to build simulation models, but not to a level where these can be used by a busy engineer or manager unless he has extensive programming experience. In an attempt to make simulation a more readily available tool, Sanford (1969) structured a generalized materials handling model (UGMHS)* for underground coal mining. The majority of materials handling systems consist of a set of moves and a set of pieces of equipment required to execute the moves. UGMHS gives a technique for describing and classifying the elements in these sets and then a technique for simulating the interactions of these elements as the materials handling system operates. To apply the model, the user simply furnishes data parameters and a fixed set of orders to the computer for his own problem. This new philosophy of dynamic simulation as applied by UGMHS was demonstrated in the paper by Sanford and Manula (1973). A dynamic model of underground coal mining was presented for the purposes of systems design and selection of equipment for a completely new operation and the analysis of existing ones for possible alterations, additions, and general improvements. The main differences between this application and its predecessors is the ability to transport material from multiple mine faces to multiple mine destinations and the ready adaptability to a wide variety of mine layouts. The second difference that characterizes the model is the deterministic simulation of equipment moves according to their mechanical capabilities and the physical profile of the mining scheme. Here, the computer generates performance data in the absence of time studies to compare equipment rather than operator performance.

Jan 1, 1974

By D. C. Yang

A practical and economical flowsheet has been developed and demonstrated by integrating the packed column flotation with the GranuFlow process for fine coal recovery. Orimulsion, which was used as an additive, served a dual purpose: first in the flotation and second in the dewatering and granulation steps. The test results on the coal preparation effluent sample show that Orimulsion is flexible and compatible with fuel oil and various frothers used in the packed column. Clean coal with ash contents of 3.0, 3.7, 4.3 and 5.1% were produced from a head sample of 33% ash at combustible matter recoveries of 72.4, 81.1, 87.5, and 89.2%, respectively. Other advantages include high throughput, low moisture, improved handleability, and reduced dustiness of the dewatered coal, thus providing a very significant economic Incentive for the integrated process.

Jan 1, 1998

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By A. Wahab Khair, Negendra P. Reddy

INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982). One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Elorgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cy to toxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le ?oux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly . Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles , of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield,

Jan 1, 1986

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By T. H. Parker

The Guasare Coal Project is located a short distance from Lake Maracaibo, in the Northwestern region of Venezuela. In 1987, Carbones del Guasare, a joint venture comprised of Carbozulia, ACC Venezuela, a subsidiary of ARCO, and AGIPCoal of ENI Group, Italy, was formed to develop the Guasare coal reserves for world markets. Drilling with the Venezuelan state of Zulia has indicated a coal resource of over 6 billion metric tons. Further exploration has delineated the Guasare deposit as an area particularly suited for cost-effective surface mining. The calculated mineable reserves of this area (300 million metric tons) and the coal quality characteristics are based on extensive core drilling programs.

Jan 1, 1989

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

By Louis D. Murino

Compared to coal or many metals industries, talc must be considered a small, specialty market catering to niches and dependent primarily on the physical attributes of the mined and processed mineral rather than the chemical attributes with copper, lead or uranium concentrate, the primary objective is the percent metal that ultimately is refined by the smelter, as opposed to the brightness, particle size distribution, trace impurities or morphology. The latter constitute the important determinants of where, how and why talc and similar industrial minerals are used. This paper addresses the talc market-place: where it is, how much of a market there is, who the producers are, available capacity, market growth, and marketing techniques.

Jan 1, 1984

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler's comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body's actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore's geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984