Search Documents

By G. Kazonich

The high costs and environmental problems associated with making iron and steel in the United states is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 32s-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

By Keat Chuan Chew, Qiao Yue Tung, Teoh Yaw Poh

"1 INTRODUCTION With a land area of 718 square kilometres housing a population of slightly over 5.4 million, as of 2014 (Department of Statistics Singapore 2015), Singapore is a highly urbanised city. Transport infrastructure is critical to keep the country and economy highly connected and functional as the population in Singapore continues to grow. The importance of a robust transport infrastructure is recognised by the Ministry of Transport in Singapore, which is working towards bringing 8 in 10 households within a 10-minute walk of a train station by 2030 (Ministry of Transport 2015). This gives rise to the rapid expansion of the rail network in highly urbanised Singapore, resulting in more tunnelling work having to be carried out in closer proximity to existing buildings. Such tunnelling work is expectedly more challenging and complex, and if not managed effectively, will impose higher risk to the adjacent buildings. Hence, the Building and Construction Authority (BCA) has implemented specific control measures to mitigate such tunnelling risks and to ensure safety of the public. 2 CHALLENGES FACED BY TUNNELLING WORK IN SINGAPORE 2.1 General Challenges of Tunnelling in Singapore With the increasing densification of the rail network in a highly urbanised setting, rail projects in Singapore are faced with several key challenges. One such construction challenge is constrained construction sites brought about by network intensification. Alongside the growth of the rail network, shown in Figure 1, other infrastructure networks in Singapore are also continuously growing. Underground interchange stations between networks become increasingly common, forcing each underground interchange station to be constructed deeper and in closer proximity to existing buildings (Figure 2). Singapore is not alone in facing this issue. The same can be observed in cities like London, in which its myriad network of subway lines pushes new lines and interchange stations to be constructed deeper."

Jan 1, 2016

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

By Ramesh Kumar Chauhan, Umakant Sharma, Manwendra Pratap Singh, Ashok Kumar Chadha

The power sector in India has an installed capacity of 267.637 GW as on March 2015. Out of this total installed capacity, the hydropower sector contributes 41,267.43 MW as renewable energy source. The development of various proposed hydropower schemes in India are primarily concentrated in mountainous regions of Himalaya and often involves underground tunnelling. Underground tunnelling of considerable magnitude is generally associated with adverse geological conditions and associated geological surprises. The main objective in case of Tunnels constructed especially for hydro projects, which carry enormous quantum of water is that, it should not leak. Moreover, the tunnels which are part of water conductor system should resist the inflow of water from the surrounding ground in order to avoid draining of natural water sources and lowering of existing groundwater levels. Lowering of water table may result in subsidence and damage to existing surface structures, loss of capacity of drinking water schemes and in some cases even catastrophic sliding of landmass. Grouting and pre-grouting in tunnels serve three different purposes i.e., Stabilization, Strengthening and sealing of the rock mass around tunnels to avoid leakage of water from tunnels. In present paper, results of grouting methodology adopted during final construction stage of RHEP (412 MW) along with the introspection of Water Pressure Tests conducted for determination of the efficacy of grouting were elaborately presented. The process, of contact and consolidation grouting which is respectively followed by water pressure tests along entire reach of HRT (15.177 Km long) were also addressed in detail. Pertaining to the results of water percolation tests (before and after consolidation grouting), it was also attempted to categorize the behaviour of different rock mass classes/ conditions in reference to different quantum of grout intake and corresponding Lugeon values. Importance of planned and dedicated successful grouting procedure adopted in hydropower project at RHEP is also emphasized.

Jan 1, 2016

By Yubo Tu, Lianqi Wei, Tianyi Zhao, Peiwei Han, Zhengchen Li, Shufeng Ye

The effect of oxygen partial pressure on the volatilization percentages of valuable metals from iron-rich pyrite cinder by chlorination-volatilization method using CaCl2 as chlorinating agent was investigated in this study. The volatile products were collected directly and analyzed by X-ray diffraction. It was found that there were CuCl2, CuCl, PbCl2, and ZnCl2 existed in the volatile products. Au and Pb volatilization percentages were almost not affected by oxygen partial pressure. Both Cu and Zn volatilization percentages were negatively correlated with oxygen partial pressure when CaCl2 dosage was no more than 4 wt%, and almost uncorrelated with oxygen partial pressure with a CaCl2 dosage of 6 wt%.

Dec 19, 2023

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By R. F. McFarlin, H. E. El-Shall

Since its inception, the Institute of Phosphate Research has examined every promising proposal in order to find an economical, practical and environmentally sound method of dewatering phosphatic clays. The in-house development of the FIPR/DIPR process (DIPR = Dewatering Instantaneously with Pulp Recycle) would appear to answer that quest. When small amounts of fibrous materials are mixed with clay slurries and flocculent, rapid dewatering occurs. Clay solids contents of 20 to 25% can be attained by simply rolling the clay mass down an inclined screen. Higher solids (>40%) are reached by physically pressing the cake; e.g., with a belt press. Because mechanical pressing devices are too expensive for phosphatic clay treatment, FIPR has developed the "sandwich" method of simultaneously dewatering the phosphatic clays and reclaiming the mine cut, as well as a second alternate, the "median strip" proposal. Economic projections of these bench-scale alternates suggest that the FIPR/DIPR process should be no more costly than present practice, when credit is given for the simultaneous reclamation accomplished.

Jan 1, 1993

By Paul Richardson

This paper discusses the drilling techniques and equipment used by Loffland Brothers Company to drill the AEC's UC-3 large diameter shaft in Nevada. Included are pictures and illustrations of the drilling-mud circulating system, the surface and downhole drill-string and the special heavy-duty mast and hoisting equipment required to do the job. The purpose and method of lining the large diameter holes along with the technique and materials used to backfill the lining to hole annulus are discussed briefly. Areas requiring improvement in both equipment design and technology for large diameter shaft drilling are discussed briefly. Shafts as large as 140 inches in diameter to depths of 5,000 feet can be drilled with existing equipment and technology.

Jan 1, 1969

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By Shosei Serata

Salt cavities have been proven to be a suitable structure for underground storage of various matters in gas, liquid or solid form. Since the technique of underground storage was developed mainly through field experiences in solution mining, a wider use of solution cavities for storage of gaseous and solid matters requires evaluation of three basic rock mechanics problems; cavity instability, boundary rock failure and surface subsidence. Cavity instability is due to the non-linear long-term creep properties of the surrounding ground media which are sensitive to cavity pressure changes associated with the storage. The cavity boundary rock failure is caused by the loss of effective confining pressure to the boundary rock media in the process of storage of gaseous and solid matters. Surface subsidence is the final outcome of the stress envelope originated around a cavity, eventually reaching the ground surface. The rock mechanics processes of instability, failure and surface subsidence are explained by using various field examples in salt domes and bedded formations. Methods of solving the problems are discussed including stress relief, stress control and computer optimization of design.

Jan 1, 1973

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By Fathi Habashi

IT APPEARS that the phenomenon of ion exchange by which saline water was converted to sweet was known to Moses and Aristotle. However, the credit for the recognition of this process is generally attributed to Thompson (1850) and Way (1850), who reported that when a soil was treated with either ammonium sulfate or ammonium carbonate solution, most of the ammonia was adsorbed and calcium was released. It was later proved by Eichorn (1858) that the adsorption of ions from ground waters by clay constituents was a reversible process. The first attempts to utilize ion exchange phenomena was in the field of water softening around 1906, using natural and synthetic silicates. In 1935 Adams and Holmes in England observed that crushed phonograph records (phenol-formaldehyde and amine-formaldehyde resins) were capable of exchanging ions.

Jan 1, 1970

By L. S. Fountain

A national survey, 1978-1980, found 180,973 waste impoundments used by industrial mining, municipal and other interests. Possibly 27,000 contain hazardous materials. The potential hazard of leaks polluting water supplies is a growing concern. An electrical technique was developed to efficiently and speedily detect and locate leaks in geomembrane-lined liquid impoundments without emptying the contents. A potential applied between the liquid and earth causes electric current to flow through leaks in the insulating geomembrane material to ground. The cur- rent density around the leak is used to detect and locate the leak. Field tests show single and multiple leaks 2.54 cm in diameter or less can be detected and located to within less than 30 cm.

Jan 1, 1986

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Hydraulic transport is commonly used in mining for moving particles or ore concentrates in pipes over long distances with a water stream. Control and monitoring of this process require sensor technology that can obtain relevant characteristics of the two-phase flow. This work investigates the acoustic emission (AE) technology for monitoring a hydraulic system with different sand concentrations, showing the strong relationship between friction behavior in the pipe and the measured AE signals.

Apr 1, 2023