Search Documents

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By Carlos A. Jaramillo, Seng Hing Ngu

"The Murum Hydroelectric Project is a 944-MW development consisting of a 145 meter high RCC dam, two 2660 meter long, 9 meter excavated diameter upper pressure tunnels, surge shafts, two 950 meter long 7 even meter OD penstock tunnels and a surface powerhouse. The project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometer from Bintulu, in the Rajang Fold-Thrust Belt, an Upper Cretaceous to Upper Eocene fold and thrust belt that extends under most of Sarawak. The Belaga Formation consists of a thick sequence of deep marine sediments currently appearing as steeply dipping strata of thin to thick bedded, fine to medium grained sandstone interbedded with argillaceous rocks, resulting on a “Flysch” type geologic environment. The project pressure tunnels were excavated perpendicularly to these strata resulting on frequent change on rock conditions and behavior, and required rock support. This paper describes the characterization of the rock mass, design of rock support, and incidents during construction. Particularly interesting were convergence issues in Tunnel 1 resulting from Tunnel 2 excavation. INTRODUCTION The Murum Hydroelectric Project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometers from Bintulu, and upstream of the Bakun Hydroelectric Project. The project consists of a 145 meter high RCC dam, a 50 meter high intake tower, two nine meter OD and 2660 meter long upper pressure tunnels, two nine meter OD and 175 meter long vertical shafts, two 25 meter diameter and 80 meter deep surge tanks, two seven meter OD and 950 meter long penstock tunnels and four seven meter OD and 50 meter long branch tunnels, two 8 meter diameter to 3.4 meter diameter and 1400 meter long penstocks installed within the shafts, penstock tunnels and branch tunnels ending in a powerhouse with 944 MW installed capacity. LAYOUT OF THE WATERWAY TUNNELS The two waterways tunnels are basically parallel as shown in Figure 1, with each tunnel supplying water to two units in the powerhouse. The tunnels start separated 25 meters center to center, but 250 meter from the intake the separation increases to 35 meters. The tunnels are lined with reinforced concrete until they reach the surge shafts and steel lined from there to the powerhouse. The tunnel profile is shown in Figure 2."

Jan 1, 2016

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By T. Mudder

The objectives for closure of a hard rock mine include minimizing long term environmental liability, attaining regulatory compliance, and maintaining geotechnical stability, while closing as cost-effectively as possible. Proper planning for closure should come during the feasibility study, design and permitting phases, and during operations as updates. The lack of a proper or updated closure plan can result in severe environmental and economic consequences. Effective mine closure is the result of a combination of innovative concepts, long-term commitments, and multi-party cooperation. The purpose of this paper is to discuss concepts, commitments, and cooperation as they relate to an effective closure plan.

Jan 1, 1999

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

The results of studies to ameliorate acid mine drainage by retarding the rate of oxidation of pyrite at source are discussed. In the transpassive region, pyrite oxidizes by reactive dissolution, mass transfer through the product layer and diffusion in the bulk solution. One can decrease the rate of pyrite oxidation by inhibiting either oxidation reactions or cathodic reactions. It is demonstrated in this study that some surface active reagents extend the passive region by affecting both the anodic and cathodic processes. The extension to higher potentials occurs by inhibition of the anodic dissolution process whereas to lower cathodic potentials through decrease in the rate of reduction of molecular oxygen and/or ferric ions. To retard the oxidation of pyrite by ferric ions, which is considered to be the dominant oxidant under conditions of acid mine drainage, it would be necessary to restrict mass transfer or promote complexation of ferric ions at the surface. Imidazoline based reagents were found to be most effective in meeting this goal.

Jan 1, 1994

By Louis J. Czel

Although lithium was first discovered by Arfwedson in Sweden in 1817, it did not reach any significant status in commercial application until 1908 when Thomas A. Edison received a patent covering the use of lithium hydroxide in alkaline' storage batteries. Edison's achievement can be regarded as a major breakthrough in the development of the lithium industry. In the years prior to 1908 lithium salts had found only modest applications in the pharmaceutical and pyrotechnic fields. The next important milestone in the growth of this net industry occurred in Germany in 1918 when Metallgesellschaft at its metallurgical laboratory at Frankfort-on-Main discovered that the addition of a few hundredths percent of lithium metal to aluminum and its alloys increased-the hardness. This brought into being a new commercial use of lithium in the manufacture of bearing metals. The new material, called "Bahnmetall" (railroad, metal), was widely used for, many years in the manufacture of bearings for railroad and automotive purposes. Its use continued until the early 1930's and there was a short-lived renewal of its production during World War II. Subsequent use of-the alloy was soon outmoded.

Jan 1, 1961

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By T. L. Myron

To determine the effect of flux crystal size on the production rate and strength of sinter, batch sintering tests were conducted on samples of both dolomite and limestone of various crystal sizes. In addition, calcination tests .were performed on the dolomite and Limestone to determine the effect of crystal size on calcination rate at various temperatures normally attained in sinter beds. The results indicate that flux crystal size does not affect sinter production rate or sinter strength.

Jan 1, 1962

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By Herman L. Bauer

The Robinson Mining District near Ely, Nevada, is one of the major porphyry copper districts in the world. Within the district is an east-trending zone of altered porphyry, metamorphosed sedimentary rocks, and sulphide mineralization surrounded by Paleozoic limestone, dolomite, shale and sandstone, Tertiary volcanics, and Quaternary alluvium. Six major disseminated ore deposits have been exploited in this eight-mile zone. About 20% of the district production has come from disseminated ore in metamorphosed sedimentary rocks found adjacent to altered quartz-monzonite porphyry. The following brief statements summarize the inter-relationship of porphyry, alteration, metamorphism, and mineralization: 1. Disseminated copper ore does not occur in unaltered porphyry or in unmetamorphosed sedimentary rocks 2. Sedimentary rocks have been only weakly metamorphosed where intruded, by unaltered porphyry. 3. Intensely metamorphosed sedimentary rocks are found only adjacent to, altered porphyry. 4. Many hydrothermal minerals are common to both altered porphyry and adjacent metamorphosed sediments. 5. Disseminated ore is found in altered porphyry and adjacent meta¬morphosed sedimentary rocks. 6. In general, there is a direct correlation between grade of ore in porphyry and copper content in the adjacent rocks. 7. Chemical changes in the altered porphyry facies and metamorphosed rock facies appear to be related:

Jan 1, 1963

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991

By Enrique Llewellyn

North River Energy Company a previous subsidiary of Republic Steel Corporation commenced development of the Number One Mine in mid-1972. The mine is located in West Alabama and presently employs a total of 632 people. Production capabilities have increased to 1.4 million clean tons of steam coal per year with the newly purchased Longwall System. Washer recovery averages 57 percent. The seam being mined is the Pratt or Corona with an average height of 52 inches and an average cover of 540 feet. The immediate roof is laminated sandstone and the floor is composed of a hard fireclay. Total production out of the mine is provided to Alabama Power Company under a longtime contract.

Jan 1, 1981

By Gary S. Brierley, Tracy J. Lyman

INTRODUCTION Geotechnical engineers play a major role in tunnel design primarily because tunnels are constructed entirely within the ground. In general, this role can be divided into two major tasks: subsurface investigations and project design. Under subsurface investigations, it is necessary for the geotechnical engineer to accurately describe the ground in which the project will be built. Under project design, it is necessary for the geotechnical engineer to work together with other members of the design team to make certain that the tunnel fulfills its intended purpose at least cost. Given in the paper are the authors' opinions about what constitutes an adequate scope of services for these two tasks on a tunneling project. SUBSURFACE INVESTIGATIONS o Background Study All subsurface exploration programs for tunnels begin with a thorough investigation of background information about the proposed site. Such background information includes geologic, reports topographic maps, aerial photography, and case history reports of other nearby tunnels. Once completed, it is necessary to study the background information so that the proper scope and magnitude of subsurface exploration work is performed in a manner that provides maximum input to a knowledge of those intact and rock mass properties that are important for an understanding of the entire ground mass. The blind application of field and laboratory techniques, no matter how sophisticated, is wasteful and potentially

Jan 1, 1989

By L. Adler

When systematically compared to other engineering fields, mining engineering is distinctive in 1) having a total systems concern. 2) dealing with encumbered space and 3) requiring full spectrum practice. The total systems concern results from having to design and then co-ordinate in space and time several major systems: excavating and bulk handling, ground control, life support and normal support. This requirement favors a generalist rather than a specialist approach. In coping with encumbered space especially in underground coal mining, the uncertainties of geologic conditions are compounded by tightness, roughness, remoteness and hazards. Into this difficult setting the total systems * complex is "stuffed," adding congestion and interference. Because of significant ground deterioration a flexible "rapid in-out" approach is usually vital to mining. Full spectrum practice arises from the need to manage, as well as to plan and design, a labor intensive operation. Since market conditions can also fluctuate most aspects of administration are needed in many respects, mining engineering functions relative to civil engineering in a way similar to industrial to mechanical engineering, with encumbered space being crucial. On this basis stress is placed on: 1) personal relations, 2) field work and 3) entrepreneurship, viewing time as money. Specific recommendations for improving engineering, safety and management and leadership are made. Since most new deposits are marginal, by applying these recommendations with high technology they could possibly now be mined on a widespread basis.

Jan 1, 1985

By J. J. Sense

The Mission Unit of American Smelting and 'Refining Company is located in Pima County, Arizona, approximately twenty miles southwest of the City of Tucson. The Unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to Company Smelters at Hayden, Arizona, or El Paso, Texas Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tons per day concentrator gas started in the spring of 1960, The first ore was treated in mid summer of 1961 and full ore production was reached in August of 1961. At that time over 46,000,000 tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tons per day. Total production to date (ore and waste) over 120,000,000 tons.

Jan 1, 1964

By Raymond E. Langen

Uranium exploration in the Powder River Basin of northeastern Wyoming has been intensive since 1966 and in 1968 produced significant discoveries of reduced uranium ore by Humble Oil & Refining Company and others. Substantial reserves have been established in the area. High-grade carnotite ore was discovered in 1951 near Pumpkin Buttes in the central part of the basin (Fig. 1). Other mineralized areas were soon established from Pumpkin Buttes south to Monument Hill and Box Creek. Total production from these shallow oxidized deposits in the lower Eocene Wasatch formation was small. The AEC reports total production of 520,000 tons of ore averaging 0.19% U3O8. The authors are indebted to many people within Humble Oil & Refining Company and Esso Production Research Company for their assistance and guidance. SUMMARY AND CONCLUSIONS The Highland ore deposit, discovered in 1968, is a large uranium occurrence located in the southern part of the Powder River Basin. Uranium mineralization consists of sooty, black uraninite and coffinite coating sand grains and is concentrated along the margins of Tertiary fluvial sandstones. Uranium was transported by oxidizing solutions roving through the buried sandstones and spreading into less permeable channel-edge sandstones to form typical rolls and tabular deposits. Unaltered sandstones are light gray to gray-buff where the sandstones have been oxidized, the colors are various shades of red, yellow, and yellowish brown. An Oligocene tuffaceous source for the uranium is proposed; however, leaching of the arkosic and tuffaceous host sediments may also have provided a source.

Jan 1, 1971

By Gary MacDonald

What is the primary function of an impact assessment? Many people at the International Association of Impact Assessment?s (IAIA) annual conference said that it is time to return to the fundamentals and consider the underlying drivers of impact assessments ? human health, safety and security. This fall, managers struggling with those fundamentals will receive extra support when a new course focusing on health and socially responsible security is launched online and in British Columbia, Canada, home to many of the world?s junior miners. Now in its 33rd year, the IAIA conference recently held in Calgary, Canada, typically brings together a range of professionals who work in the impact assessment field, including academics, as well as people conducting applied disciplines, such as social and environmental performance management. It is a chance for people grappling with how to assess impacts from projects (for example, dams, mining and other extractive projects), to compare notes and to talk about developments in how to measure, track and report on them. The comments about returning to fundamentals rose as participants talked about the ongoing and increasingly recognized divergence between three main impact assessment streams: environmental, social and health (EIA, SIA and HIA, respectively). Discussions in sessions and in the corridors included calls for streamlining, for integration, for improvement and sharing of practice ? particularly in the HIA stream, where those deeply engaged in the health discipline questioned how HIAs and their intended outcome of protecting human health can be better integrated into the EIAs or SIAs that dominate the impact assessment realm. EIAs and SIAs have become the main tool, particularly from a permitting perspective for large-scale mines, but seem to leave projects with little real information about what they need to do. Human health is not the only concern re-emerging. Although not reflected at the conference, there appears to be an emerging understanding of the need to link the determinants of health with socially responsible security practices. Companies conducting independent social performance assessments for international financial institutions based on the International Finance Corporation?s Environmental and Social Performance Standards increasingly wrestle with both community health and security issues as extractive companies encounter challenging social environments around the world. Once again, the intended outcome is to better protect human health, including avoiding health impacts from conflict, abuses and violence.

Aug 1, 2013