Search Documents

By H. G. Kok

The concept of mobile crushers is not new. Since their introduction about twenty-five years ago, mobile crushers have continued to gain widespread attention. Mobile crushers reduce minerals in the open pit mine to sizes which can be transported by belt conveyors thereby reducing or eliminating the need for truck haulage. Truck haulage is costly, often representing as much as 50% of the total mining cost. More than 80% of the cost of truck haulage is for fuel and lubricants, tire replacements, and operators' wages, and it can be anticipated that the cost of these items will continue to increase at a steady pace. Compared to truck haulage, transportation by belt conveyor is more energy-efficient, less labor-intensive, and less subject to inflation. Therefore, mobile crushers, used in conjunction with belt conveyor systems, offer one of the most effective available methods of reducing energy consumption and mining costs,

Jan 1, 1980

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By David C. McLean, Peter Penner, Martin de G. Salter

The Rogers Pass Project for C.P. Rail includes a 14.7 km tunnel and an 8.5m diameter concrete lined ventilation shaft to a depth of about 335m. The shaft collar is in bouldered water bearing glacial till to a depth of about 95m. Initial excavation in the overburden was with the aid of dewatering wells. When ground support problems arose the excavation was completed by a two stage freeze programme. Freeze holes were drilled from the shaft bottom. This most unusual method was successful in overcoming the difficulties safely and efficiently. The remainder of the shaft was sunk and lined conventionally. Finally, a central dividing wall was poured by jump forming from the bottom up. The wall was completed to a high standard at up to about 20 vertical metres per day.

Jan 1, 1989

By F. C. Appleyard

A couple of miles southwest of the town of Saltville in the western tip of Virginia is a little village called Plasterco. Gypsum has been produced in this area since about the year 1815, being originally found as small outcrops at the surface. Production in the early days was very small, and the use of the mineral was limited to that of "land plaster" or ground gypsum which was spread on the land to sweeten the soil. In the late 1800's, a small calcining plant was constructed and the production of gypsum plaster began. About this same time, the surface rock was depleted and it became necessary to begin underground mining operations in order to maintain a continuous supply of raw material. The United States Gypsum Company became interested in this property in 1909, and has operated there ever since, having enlarged the calcining mill and built a plant for the manufacture of gypsum wall-board in the middle 1920's. Production of gypsum continues from underground' mining operations, and the present mine at Plasterco is now about 1,000 feet below the surface, making it the deepest gypsum mine' in the world.

Jan 1, 1965

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By S. G. Vick, K. E. Robinson, W. D. Webb

INTRODUCTION This paper discusses two uranium tailings waste disposal studies that reflect the United States Nuclear Regulatory Commission (NRC) regulatory actions and their changing requirements during the mid to late 1970's. Present guidelines require that all new uranium tailings impoundments be designed and constructed to eliminate, to the extent that it is reasonably achievable, exposures and risks to the public from the tailings. This includes positive measures for control of seepage losses from the impoundment and for control of radiological releases caused by wind and water erosion. Long-term stability of the reclaimed impoundment is also a very important requirement. That is, it is intended that the tailings impoundment, once it is reclaimed, will require little or no care or maintenance as long as the uranium tailings remain a hazard. Principally because of the long-term stability objective, the NRC has now identified subsurface burial of the tailings as the "prime option" for tailings disposal. The environmental implications of these proposed regulatory actions are obviously desirable. The economic implications the actions may have on a particular project are not always so obvious because they are so dependent on environmental suitability of site conditions. Selection of a site with favorable topographic, geologic and hydrologic conditions will usually result in the most economically and environmentally attractive alternative for tailings disposal. The first project discussed in this paper was initiated before the NRC guidelines had been developed to favour subsurface burial. At the beginning, seepage and radon emission control requirements were moderate. Constraints were imposed on the design by site topography, geology, and project capitalization considerations, factors which were dealt with according to straightforward engineering and design principles. More serious constraints were imposed by changing regulatory requirements. Unlike the more usual engineeringrelated constraints, regulatory requirements were upgraded during the design process, causing the design itself to undergo numerous modifications. The second project was initiated after the NRC proposed regulations had become better defined and below grade burial appeared to be the preferred

Jan 1, 1980

By J. O. Leppinen

FTIR measurements using a special ATR cell were carried out to investigate the adsorption of two thiol collectors, potassium ethyl xanthate (KEX) and sodium diethyl dithlophoshate (NaDTP), on an unoxidized lead sulfide surface. Both qualitative and quantitative determinations of the collectors were made at the coverages from two monolayers down to 2% of the monolayer. The experiments revealed that the thiol collector species coordinate to the lead atoms at the surface of lead sulfide but the surface products distinctly differ from the precipitated bulk lead compounds. There exists a linear relationship between the coverage and the signal intensity of the IR spectra within the coverage range studied.

Jan 1, 1987

By A. Moharana

A massive slide at Bingham Canyon wiped out a side of the pit and covered the main haul road in and out of the pit. All pre-slide mine designs and schedules were no longer valid. New designs and schedules needed to be developed quickly to provide management with information regarding the immediate post-slide production potential and the time needed to ramp back up to full production. At the time of the slide, an effort was already underway to convert Bingham?s in-house Medium Term Scheduling Process to MineSight®?s Schedule Optimizer (MSSO). One of the main reasons for doing this was to reduce the time needed to produce Medium Term Schedules at Bingham, which involves a complex shovel-based scheduling approach with shovel productivities based on shovel type and the types of mining cuts to which the shovel is assigned over each planning period. The objective of the schedule was to maximize shovel usage, satisfy mill feed requirements of four SAG mills with variable milling rates, and have flexibility in setting truck constraints. This paper will describe how the new MSSO-based mine scheduling process met the challenge of producing new schedules for Bingham in a minimal amount of time.

Feb 23, 2014

By J. A. Madonna

Universities and colleges in three countries, Australia, Canada and the United States, recognized the need to establish and/or reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral industry organizations cooperated in the study by providing information regarding their specific training needs for support personnel. The data gathered has been used to identify training areas for semi-skilled, skilled and technical personnel in geochemical mineral exploration, including, but not limited to, geological skills, geochemical skills, environmental skills and computer skills. With the areas of major educational need defined for geochemical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will be discussed.

Jan 1, 1993

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former's delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter's delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987

By L. Alagha, L. Sanchez-Calderon, M. Silwamba, W. Kirk

Selenium-rich metallurgical waste, also known commercially as “crude selenium,” is a byproduct of the copper (Cu) refining process. This by-product, contains ~ 90% selenium (Se), precious metals, platinum group metals (PGMs), and other critical elements. This study investigated the leaching efficiency of Se from the sludge under alkaline conditions using different oxidizing agents to enrich PGMs and precious metals in the leach solid residue. The effectiveness of each oxidizing agent during leaching was assessed and compared. Additionally, Eh-pH diagram for Se was established under specific experimental conditions and utilized to inform process optimization. Key variables, including leaching time, temperature, and oxidant concentration, were evaluated for their impact on the efficiency and the selectivity of the oxidative alkaline leaching process.

Feb 1, 2025

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By Edward L. Vickers

When I was originally asked to give this talk, I had certain preconceived ideas of the mining industry's reaction to Operations Research. It seemed at the time to be a rather simple task to collect these ideas for presentation here today. Jotting down these notions, I became concerned that overexposure to this activity called OR perhaps had clouded my outlook on what was actually being done on a nation-wide scale. I felt, to have a better cross section, a questionnaire of current industrial activity was in order. I solicited the response of some 75 mining companies varying in sizes and operating characteristics, and I am pleased to report that the response was good. I received answers from 51. The questionnaire was intended to measure the degree to which their concerns were actually engaged in OR efforts. With all due respect to the people who were so gracious as to answer the questionnaire, I feel that there is a tremendous misconception as to the designed purpose of OR. This is not to imply that there are no active OR groups in the mining industry. But by in large, the majority of the companies sampled appear to be somewhat confused as to what OR really is.

Jan 1, 1962

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By Ronald R. H. Cohen, Margaret W. Staub

Two pilot scale bioreactors designed to treat acid mine drainage primarily using sulfate reducing bacteria were constructed underground at the Eagle Mine Superfund site in Minturn Colorado. The project was designed to test th applicability of microbiological treatment on water with high metals concentration and to test the process in an underground environment. Objectives were, 1) to compare metal removal, pH increase, and sulfate reduction in a single stage reactor with a double stage reactor of equal volume at varying flow rates; 2) to determine where within the substrate treatment occurs· and 3) to examine volume versus surface ara as a design parameter for optimizing metal removal processes. Results from the reactors showed that the single stage reactor and double stage reactor performed equally well for the removal of Cd, Cu, Pb, Fe, Mn, and Zn. pH increased above 6.5 in both reactors. Greater than 97% of metals were removed within the first ten inches of substrate. Volume proved to be a more useful parameter for determining removal rates than area. Using volume as a design parameter rather than surface area enables PMDT systems to be constructed as packed columns rather than broad wetlands, Thus, space requirements are significantly reduced.

Jan 1, 1993