Search Documents

By J. A. MacLellan

It is the hope of the author that this paper, largely a compilation of observations and opinions built up over 20 years of experience in cold and remote areas may be of some help to others in designing better plants for the future in the north. The north is not as difficult to operate in as the better story tellers make it appear to be. ()n the other hand for 6 months of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut a multi-million dollar plant down at -4n' F with a 4n M.P.H, wind. It only takes one man door improperly latched to freeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later while you are having Christmas dinner, a watchman will call up to report that the whole plant is flooded because the main water line just froze up and burst. Basic things to remember in plant design for cold and remote areas are: everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore he kept to an acceptable minimum. Service areas on the other hand must he adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles for instance have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50° F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze up. People in a remote area are expensive. The capital investment per employee may be as high as $30,000; with fringe benefits per annum costs of an employee will he as high as 812,000 per year regardless of basic wage rate. It

Jan 1, 1971

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By Felicia F. Peng

A laboratory fixed bed reactor was used in a study of generating clean thermal energy from coal fine refuse-limestone agglomerates. The major operation variables, including Ca/S mole ratio, agglomerate size, air flow rate and temperature, which affect the rate of sulfur fixation and combustible material utilization, have been examined. The test results show that 70 percent or more of sulfur fixation and 100% of combustible material utilization can be achieved depending upon sorbent, agglomeration, and combustion conditions. The coal fine refuse limestone pellet combustion process (CLC process) requires a simple flowsheet to convert coal fine refuse as a clean solid fuel, while meeting the strict air quality standards for SO2 emissions into the atmosphere. The CLC process is an attractive method to clean up coal slurry impoundments to protect our environment.

Jan 1, 1984

By C. K. Arthur, N. K. Dumakor-Dupey, B. A. Kansake, F. A. Kaba

Autonomous mining systems have been deployed for improving mine performance. However, there is a fear of job losses. Adoption of autonomous systems is envisaged to be resisted by major stakeholders in Ghana due to high illiteracy and unemployment. This paper assesses the preparedness of Ghanaian mining stakeholders for the adoption of autonomous systems to Ghana’s surface mining industry. Closed and open-ended questionnaires were administered to mine stakeholders. Respondents generally expressed unwillingness to accept autonomous systems into Ghanaian mines due to fear of increased unemployment. We propose setting up a mining education fund (MEF) for training stakeholders in autonomous mining systems. INTRODUCTION Mining contributes enormously to the sustenance and growth of global and national economies through the provision of raw materials, employment, revenues and foreign exchange (Carvalho, 2017; ICMM, 2017; Cordes et al., 2016; Solomon et al., 2008; Walser, 2000). The International Council on Mining & Metals (ICMM, 2014) reported that globally, formal mining employs approximately 2.5 million people. Many resource-rich countries, especially the developing ones, have experienced strong socioeconomic growth propelled by the discovery and extraction of valuable minerals. McMahon and Moreira (2014) reported a positive linkage between mining and sustainable development. They revealed that averagely, resource-rich countries have improved Human Development Index (HDI) scores than countries without mineral resources. Mining remains a crucial industry in Ghana’s economic development (Bermúdez-Lugo, 2016; Amponsah-Tawiah and Dartey-Baah, 2011). Over the years, mining has contributed significantly to the gross domestic product (GDP) of Ghana. In 2013, mining accounted for 1.7% of Ghana’s GDP and about 19% of government revenues (Ghana Chamber of Mines, 2015). The Ghana Chamber of Mines also reported that mining contributed over 50% of foreign direct investment, 37% of export earnings and 1.1% of direct employment revenues. The US Department of Energy (DOE) estimates that 65% of coal, 92% of metals and 96% of industrial minerals are mined using surface mining methods (DOE, 2007). Generally, mining is a capital-intensive venture, with high operating cost, hence there is a constant demand for mining companies to seek efficient cost reduction and production maximization strategies. One strategy being pursued keenly is automation, which is noted to improve productivity, and worker safety at minimal cost. According to Parreira (2013), mining automation involves direct teleoperation whereby workers remotely control the mining process using computers from a control room.

Jan 1, 2019

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By James A. Bloom

To operate the Morris Fork Preparation Plant with a closed water circuit has been an elusive goal for Union Carbide. The benefits of a closed circuit have never been questioned. The removal of fine solids from washery water makes possible the recirculation and reuse of the water. Heavy media drag tanks and other separating machines perform better and more consistently with washery essentially free of fine solids. Finally, the production of a clarified effluent makes unnecessary the sludge ponds usually associated with a coal preparation plant. Why then do I say elusive? Because, since plant design was completed in 1970 we have been in hot pursuit of an ever-growing fine solids problem. In four years the minus 28 mesh material in the plant feed has nearly doubled. The replacement of conventional sections with continuous mining machines has led to a lowering in size and quality of product from the mine. In addition, increasing emphasis underground on roadway clean-up has contributed to the fines problem.

Jan 1, 1975

By John Hanna

The Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of phosphate minerals from siliceous ores. The process takes advantage of preferential adsorption and high reactivity of fatty acid collectors towards apatite over silica surfaces under slightly acidic conditions of pH 5-6.5. The process was successful in upgrading various phosphate samples from Florida and North Carolina containing 7.7-15.3% P205 and 62.3- 77.2% Insol to concentrates assaying 28.1-33.1 % P205 and 4.1-9.9% Insol with high P2O5 recovery of 81.8-92.2%. Depending on the type of silica impurities present one or more cleaning steps, with or without sodium silicate, would be required to improve the grade of the rougher phosphate concentrate.

Jan 1, 1992

By R. E. Vivas, J. A. Villa

"Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.1 Mt/a (4.5 million stpy) of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this article and include improvements in geo-modeling, mine planning, and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution.Project overviewPeña Colorada is a mining company that produces about 30 percent of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in Fig. 1. Technological innovationsMost mining projects around the world typically follow the logic of “mining the next best ore.” Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that improved many aspects of the mine plan. The Peña Colorada block model has undergone 3 expansions to reflect additional information not available in the past. The model has expanded to the East and Southwest. The latest model expansion increased the total number of benches to 98 as a result of positive exploration results. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. Two sectional block model views in Hexagon Mining’s MineSight 3D, along with the pit designs and geologic solids are shown in Fig. 2."

Feb 1, 2017

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By Gary Bennethum, L. Courtland Lee

INTRODUCTION For any identified mineral resource to qualify as a minable reserve, it must contain legally and economically extractable mineral at the time of determination. As competition for land has increased, the legal complexities have more than kept pace, frequently becoming the most important determinant in mineral exploration and development projects. Rarely will developers of a project avoid having to obtain numerous federal, state, and/or local permits while acquiring the necessary legal permission to begin mining. Each site must be selected carefully, not only for economic feasibility, but also for legal feasibility. Although it is impossible to present site-specific solutions for all potential underground developments, certain generalizations may be applied to specific land categories, particularly federally owned land. Such federally owned land includes more than 33% of the land area of the United States and many of the areas potentially attractive for future development. State and local restrictions affect a large portion of the nonfederal land, and those restrictions are equally important even though their diversity and current status require more regional study than can be provided herein (the list of references include sources of additional information). Each potential mining site requires a title search of the land status to determine the land ownership and the conditions affecting development. In addition, appropriate data concerning the mineralogic and economic potentials of an area must be collected. As listed in Table 1, many sources of public information are avail- able to aid potential developers. Fig. 1 illustrates a typical federal master title plat. HISTORICAL PERSPECTIVE The settlement of the United States reflects a fascinating history of public-land laws and subsequent mineral-disposal laws. Most of the statutes of the eighteenth and nineteenth centuries sought to dispose of land for the purpose of generating revenue to the federal government. The underlying need for general revenue contributed directly to numerous and often conflicting land policies. More recently, diverse federal programs such as environmental legislation have transcended the need for revenue in forming the framework that determines who has power over mineral developments and where those developments can take place. In 1812, the General Land Office was established under the Treasury Dept. At that time, English common law prevailed, entitling the owner of the surface to whatever was contained within the surface boundaries from the surface to the center of the earth. Unless a distinct title separated the mineral estate, it was included in the surface-land ownership. However, gold and silver were the property of the crown and were controlled by sovereign prerogative. Early state legislation on the subject of mines and minerals may be classified as legislation providing for the sale of state lands with a reservation of the minerals and legislation recognizing or asserting the sovereign prerogative for precious metals. In 1781, a Pennsylvania statute reserved 20% of all gold and silver ore for the use of the commonwealth. Thomas Jefferson suggested that a portion of all gold and silver be retained by the federal government. These early rules affecting land in the eastern states, now privately held, have been re- pealed, declared obsolete, or largely ignored. Federal legislation prior to 1848 and affecting mining may be classified as legislation reserving the minerals to the United States and legislation authorizing the disposition of reserved minerals by sale, lease, or grant. With many modifications, these basic policies remain in effect at the present time. A 1796 act provided for the sale of the Northwest Territory and for the establishment of the present system of rectangular survey for public lands. The Lake Superior copper region was the scene of "wild and baseless excitement in 1837" when the attorney general concluded that the president had the power to lease lands in Wisconsin; this opinion soon was overturned by another attorney general. By 1846, Congress had passed legislation authorizing the president to sell reserved lead mines "as soon as practicable" since the system of granting Leases had proved to be unprofitable to both the government and the lessees, many of whom refused to pay the rent. The general practice of early federal Legislation was to make a distinction between mineral lands and other lands, deal with them separately, and generally withhold mineral lands from disposal except through special legislation dealing with particular land. In 1848, following the treaty of Guadalupe Hidalgo, a vast land area was ceded to the United States by Mexico. This area included the present states of California, Nevada, and Utah, as well as portions of Arizona. Colorado, New Mexico, and Wyoming. This abolished the Mexican laws and customs relating to mining and preceded the adoption of the miners' own rules and customs. The adoption of those rules and customs followed a hard-fought battle between western congressmen and the eastern establishment. The western congressmen advocated adopting local customs through a location patent system, while the eastern establishment, particularly in Ohio and Indiana, favored an all- leasing system to pay off Civil War debts. The first mining law was passed in 1869 as an amendment to an act granting right-of-way to ditch land owners, and it was followed by the 1872 Mining Law. Precedent was established for the first categories of protected lands in the opening words of this act, which included the phrase "all unreserved" lands. Reserved lands subsequently defined included military and Indian reservations and were excluded from location since they were determined to be reserved lands. However, the overriding purpose of the mining laws was to settle the western lands and generate revenues for the federal

Jan 1, 1982

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By STEVEN J. SCHATZEL, Zoheir Khademian, KAYODE M. AJAYI

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine, creating safety concerns. To provide recommendations for developing guidelines that ensure a safe coexistence of longwall mining and unconventional shale gas production, this study uses a discrete fracture network (DFN) model to evaluate the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements.

Mar 1, 2023

By C. J. Milam

Oil shale may not produce the same excitement of the gold rush days, but presently there is an "oil shale fever" among mining men. Such exotic equipment as 800-ton haul units, 75 ft. boring machines, and huge fully automatic multi-purpose jumbo drill units are only a few of the topics of conversation in the oil shale groups. I am dreaming, perhaps, but this type of exotic thinking will exuberate the advancement in mining technology and will only be tempered by the practicality and the availability of today's equipment.

Jan 1, 1975

By D. J. Benton, S. Finley, D. T. Orr, A. J. Chambers, M. A. Stepan

"Corrosion of ground support can lead to falls of ground that pose a significant risk to miner safety. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) is investigating corrosion at the Hecla Mining Company’s Greens Creek Mine, located near Juneau, Alaska, USA. Field studies have used photogrammetry surveys to document welded-wire mesh corrosion, and laboratory studies at NIOSH’s Spokane Mining Research Division (SMRD) have investigated the effects of corrosion on ground support integrity. Findings show that (1) corrosion monitoring through photogrammetric methods may be effective for qualitative measurements of welded-wire mesh corrosion, and (2) there is a relationship between loss of load-bearing capacity and the diameter loss due to corrosion in welded-wire mesh. Photogrammetry results thus far have measured an apparent bulking of the corroded welded-wire mesh, and preliminary laboratory tests have investigated the relationship between the larger bulked and effective wire diameter. If this relationship is verified, these results may indicate that photogrammetry, when combined with the models produced in laboratory tests, could offer a means of monitoring corrosion levels, as well as rock rib deformation. INTRODUCTION Reducing the number of rock fall injuries and fatalities is an important part of the mission of the National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD). Ground control using support systems to protect miners from rock falls is one of the oldest mining sciences, and considerable research has led to a variety of modern tools and methods in use today. Among these tools are rock bolts and welded-wire mesh, which are made from increasingly higher-strength steel grades to meet the increasingly demanding requirements of underground mines [1]. However, the benefits of these higher-quality support elements may be negated in corrosive mining environments. A better understanding of how corrosion affects the support capacity of ground support systems will assist engineers in determining when an opening is at a greater risk of falls of ground. Accelerated corrosion has been occurring in some areas of the Hecla Mining Company’s Greens Creek Mine near Juneau, Alaska, USA. Corrosion of ground support has resulted in two falls of ground occurring between April 2015 and March 2016. While these falls of ground did not injure any personnel, mine management recognized the high risk to miner safety and responded by actively undertaking a ground support rehabilitation program. Rehabilitation measures include the installation of both galvanized and coated, corrosion-resistant bolts and welded-wire mesh, depending on local conditions."

Jan 1, 2017

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By Paul D. Tomlingson

The difficult and often harsh working environment of the mining industry can stress both personnel and equipment to the extreme. Often, the unintended consequences of this environment lead to confrontations between departments, as each goes about its tasks of mining, maintaining or supporting these activities. On occasion, the confrontations may result in criticism of other departments for perceived or real sins or omissions. The offended department may not be able to change the circumstances, but can only complain while frustration persists. The most effective solutions are the actions of the mine manager. By establishing mutually supporting roles of each department and specifying conditions for the interactive conduct of maintenance, the mine manager can better assure that the inherent problems of the mining environment are neutralized.

Jan 1, 2011

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024