Search Documents

By W. Burr Bennett

The prestressed concrete industry in particular, and the precast concrete industry to some extent, are rank newcomers to the concrete construction field compared to the cement, ready-mixed or concrete masonry industries. This young industry reflects its youth and vigor in its enthusiasm, optimism and the belief that it can reach any goal it chooses to set -- and it is setting its sights high. The prestressed and precast concrete industry fully expects to become the major structural and architectural material by the 1980's. Before exploring how the industry expects to reach this goal, a brief look at the origins and the growth of the industry may be useful in an evaluation of the feasibility of this goal. It was always recognized that concrete, strong and efficient for supporting loads which cause compression, was weak and inefficient when used to carry loads which induce tension. Thus the reason for reinforced concrete in which the concrete efficiently carries the compression in a flexural member while low grade steel bars reinforce the concrete in the areas 'of tensile stress. (Fig. 1). The steel being relatively inexpensive, can passively, but quite effectively carry tensile force while the concrete carries compression. The concrete in contact with the reinforcing also protects the steel from corrosion and acts as insulation to provide a superior "built-in" fire resistance. The major disadvantage of reinforced concrete relative to its main competitor, steel, is its weight in relation to its load-carrying capacity. Reinforced concrete systems, such as waffle slabs, I-beams, thin shells, etc. ,

Jan 1, 1971

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Wade Edward Speer

The Hiddenite District of Alexander County, NC has produced some of the world?s finest large emeralds since the first one was discovered 134 years ago. In fact, North America?s largest emeralds come from the district, making this one of the continent?s most unique gem deposits. In addition to emeralds, the Hiddenite District is also famous as the discovery site for the rare spodumene mineral hiddenite, first identified in 1881. Nowhere else in the world do these two minerals naturally occur together. The emeralds are a unique color variety of beryl (Al2Be3Si6O18) with trace amounts of Cr+3 and V+3 substituting for Al+3. The hiddenite (LiAlSi2O6) crystals also exhibit emerald green color due to traces of chromium. Consisting of three large deposits and numerous prospects, the district encompasses an area of 10 km2 (4 sq miles) centered on the small town of Hiddenite. Operations at the Adams, Ellis and North American Emerald Mines properties have been productive at irregular intervals since the 1880s. Currently, only the North American Emerald Mines property is being mined on a regular basis. Recent activity there has exposed a 3-hm2 (7.4-acre) pit with depths of 25 m (82 ft) that provides the best exposures of unweathered bedrock seen in the district in more than 120 years. Although no official records exist, public and private data indicate that the production of the entire Hiddenite District from 1880 to 2007 is about 70,000 carats of emerald and 20,000 carats of hiddenite. The bulk of the emeralds came from the North American Emerald Mine property (NAEM, formerly known as the Rist Mine) where sustained mining replaced the previous sporadic prospecting in 2000.

Jan 1, 2009

By R. L. Brown

The Buchans mining district is located roughly at the center of the island of Newfoundland and contains some 18 separate mineral deposits. The first of these deposits was discovered in 1905, the latest discovery having been made in 1979. To the present (1983), some 16 Mt (17.7 million st) grading 1.33% Cu, 7.5% Pb, 14.5% Zn, 115 g/ t (3.7 oz per ton) Ag, and 1.4 g/t (0.04 oz per ton) Au have been mined. Mining operations are now largely terminated, but a few hundred thousand tons of economically marginal reserves may be mined in a salvage operation. The Geological Association of Canada Special Paper No. 22, "The Buchans Orebodies, 50 years of Mining and Exploration," contains papers which describe the history, geology, and the application of evolving geological concepts in exploration. Papers by Neary, Swanson, and Thurlow and Swanson in that volume are topical to the present discussion. Successful exploration techniques at Buchans included physical prospecting, utilization of the state-of-the-art geophysical techniques, saturation diamond drilling which was made possible by the high gross value of the existing ore, and, since 1955, diamond drilling directed by fairly well understood geological parameters. The record of discovery started in 1905 when the Buchans River deposit was found by Matty Mitchell, a prospector employed by the Anglo- Newfoundland Development Co., a British company which owned mineral rights over a very large area in the Red Indian Lake-Exploits River drainage system.

Jan 1, 1991

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Chunhui Zhang, Enton Bedini, Jiang Chen, Fengchao Yang, Hang Dong, Xiaoyan Chen

The alteration formed by the reaction of ore-bearing fluid and wall rock is often used as an important prospecting indicator, resulting in the dilution or enrichment of metals or related trace elements. A variety of rock-forming and metallogenic elements have been analyzed in regional stream sediments so that the relationship between the ore-bearing altered rock and the change in the geochemical elemental content can be obtained. Therefore, by using appropriate models, such as matched filtering, the abundance of the distribution of wall rock alteration, similar to the discovered deposits, can be modeled by using the distribution of geochemical elements in the region, and the areas with high distribution abundances are usually favorable prospecting targets. The alteration types related to gold mineralization in the Baiyun gold deposit are potassium feldspar alteration, silicification, pyritization, sericitization, and chloritization. In this paper, the geochemical data of the Qingchengzi ore field (1:200,000 and 1:50,000) have been used to form geochemical images through rasterization. In the three sections of the Baiyun gold deposit, binary-coded curves have been formed, revealing the differences in geochemical elements in stream sediments between altered rocks and the rocks surrounding the Baiyun gold mine. Among them, Au, W, and Mo are enriched elements, while Sn, Zn, and Hg are depleted elements. Several gold deposits are found in the predicted altered rock area by using the matched filtering method during fieldwork, which shows the effectiveness of the method.

Dec 30, 2023

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

While SME is hosting its Annual Meeting at the Phoenix Convention Center, Feb. 28 to March 3, one of the finest collections of mining history will be on display just 15 blocks away at the Arizona Mining and Mineral Museum. Inside the museum, visitors will be treated to a treasure trove of minerals, gems, me¬teorites, rocks, fossils, mining artifacts, historical exhibits and interactive displays on modern mining. The museum is located at 1502 West Washington. For SME Annual Meeting attendees, this is a free, eight-minute Dash bus ride 15 blocks west of the Phoenix Convention Center.

Jan 1, 2010

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By C. J. Newman

Before 1995, the smelting process at the Kennecott Utah Copper Corp. (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. When considering expansion, it was decided that the existing process would not lend itself to a program geared toward processing the total output of copper precipitate and copper concentrate from KUCC mining and concentrating operations. During 1989 and 1990, several smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1 Mt/a (1.1 million stpy) of copper concentrate, with the ability to expand to 1.2 Mt/a (1.3 million stpy). The smelter facility that used the Noranda technology was shut down in May 1995. The flash smelting furnace operation began in June with the flash converting furnace start-up a few weeks later.

Jan 1, 1999

By Randy N. Powell

The Pipeline gold ore body was discovered in Lander County, NV in March 1991. Construction of the new mine and mill did not start until early March 1996. The $289-million project was placed on a fast-track development schedule upon completion of permitting and corporate approval. The mine and mill were commissioned 11 months after the start of construction and the project ended up $40 million under budget. Project design and construction management were provided by Placer Dome Project Development Division (PDD). History The Cortez Joint Venture has operated in northeast Lander County since the late 1960s. The business structure is comprised of 60% Placer Dome and 40%Kennecott Exploration. Throughout the years, production has been from several small open-pit deposits— Cortez, Horse Canyon, Gold Acres and now Pipeline.

Jan 1, 1999