Search Documents

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By Vernon N. Cox

From comments and questions concerning the meaning of USNR, and "why is the Navy in the mining business?" I believe it is worth while to establish the background and purpose of our company. We are a stock company formed by the purchase and reorganization of a company known as the U. S. Natural Gas Corporation. In May 1969, a group of investors with Mr. Robert L. Katz as president and chief executive officer, created United States Natural Resources, Inc., to develop and purposively use our Natural Resources in four areas: 1. Mines and Minerals 2. Forest Products 3. oil and Gas 4. Recreational Lands As final proof that we are not a government organization, I simply state. "We pay taxes." The mining division was formed in October 1969, with the completion of the merger of USNR and Vibration Measurement Engineers, Inc., Of Evanston, Illinois. Throughout the industry we were known as "VME," our company supplied consulting service in the field of seismic energy control, mining consulting and. we operated drilling, blasting and, contracting organizations in several areas of the country. Since that time we have developed and acquired producing properties in Quarrying, Coal Mining and Cement Copper Production.

Jan 1, 1971

By A. Anani

The goal of hot mix asphalt (HMA) design is optimal material blending to meet Superpave specifications. HMA cost minimization has being modeled as linear programing (LP) (Awuah-Offei et al 2011) and mixed integer LP problems (Brown et al, 2012) and solved with commercial software such as LINDO and CPLEX. Often these software, which are designed to solve general optimization problems, have licenses that cost thousands of dollars. The objective of this study is to develop a novel solution algorithm to the HMA optimization problem presented by Brown et al. (2012), which will negate the need for expensive commercial packages and is specific to this problem. This novel algorithm is based on the branch and bound algorithm for solving mixed integer problems. The algorithm is incorporated into a software package with an easy-to-use graphical user interface. The developed algorithm is validated using a real-life HMA problem. Using this solution algorithm will save companies thousands of dollars, otherwise used to purchase software licenses.

Feb 23, 2014

By Eugie Kabwe

The increase in depth of mines due to the depletion of surface deposits leads to unsafe tunnel construction and overall ore extraction. This is due to tunnel instability associated with the surrounding rock mass’s ability to exhibit creep that occurs over time. However, the explicit description of this mechanism using conventional constitutive models has proven to be difficult and inadequate. Hence, this paper presents an integrated viscoelastic viscoplastic visco-damage model with the Duvaut-Lions function. The presented model is calibrated by experimental data to determine the viscoelastic viscoplastic and visco-damage parameters. It is further implemented in a finite volume numerical code and verified on an experimental scale by numerical modeling of a cylindrical specimen. It describes the 3-phase creep mechanism perfectly as compared to the inbuilt conventional integer-order derivative model. Results from the conducted verification show that it can successfully be employed to describe the long-term behavior associated with the creep mechanism.

May 16, 2021

By Albert H. Fay

The gypsum industry makes significant contribution to the wealth of our nation. This non-metallic mineral ranks in the highest order with America's most precious resources. Evidence of this is borne out by the fact that gypsum is a vitally necessary element in the building, industrial and agricultural industries. In 1967, the United States consumed 14 million tons of this valuable ore. Of .this amount 69% was required by the building industry for the manufacture of building materials. An additional 21% was directed to the industrial market, for the manufacture of Portland Cement and for other industrial uses. The remaining 10% was used for agricultural purposes.

Jan 1, 1969

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

By H. Kinilakodi

The authors previously developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the safe performance index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the health and safety risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency or the U.S. Mine Safety and Health Administration (MSHA) in recognizing and addressing emerging problems with actions that may have been able to predict high-risk conditions, the fatality and/or other serious injuries. The approach would have given extra scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By I. Abdullayev, M. Soberano Capistran, J. Garcia

The application of post-tensioning in segmental structures was introduced in the early 1900s and has been successfully applied in different types of structures including immersed tunnels, bridges, buildings, metro stations, and stadiums. There are, however, only five known circular concrete tunnel projects where the post-tensioning approach has been adopted. This paper discusses the application of post-tensioning to mitigate the high internal operating pressures in an effluent outfall tunnel project 7 miles, 11.3 km long, currently under construction for the Los Angeles County Sanitation Districts, LACSD. This project will be the first use of post- tensioned segmental concrete tunnel linings in North America.

Jun 23, 2024

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

By J. Peterson, P. G. McKneight, R. W. Riggle

"In today’s tough mining environment, the key difference between surviving and thriving is how effectively miners optimize their mining operations. This paper explores the compounding effects material fragmentation has on mining costs and productivity. Starting with Drilling & Blasting and moving through Loading, Hauling and Crushing, we will illustrate the opportunities to improve operating costs and thus reduce the Total Cost of Ownership (TCO) of the total mining system. Material size and volume requirements are defined by the needs of the mill or plant, and drive the rest of the mining operation from the bench through the primary crusher. At the start of the cycle, where the rock mass is drilled and blasted, the degree of fragmentation and the muck pile configuration is determined, as are the effects on cost and productivity of all subsequent operations. The cost of managing oversize material, including secondary handling, overloading, reduced diggability, higher load factors, extra pass loading, increased wear factors and reduced throughput rates are all opportunities for improvement. INTRODUCTION Having visited many mine sites, customers are asking about the end to end mining value stream from loading to the crusher and how to measure the cumulative effects on each part of the mining value chain. All too often improvements with the drilling and blasting may impact fragmentation but do not improve the diggability so the net change on cycle times or fill ratios is perceived to be negative at the point of loading but they may have a measured improvement going through the primary crusher. This makes it imperative to measure performance at each segment of the overall cycle and not just to the crusher but thru it. The mine material process originates with solid rock, in-situ, and progresses to the output of the primary crusher. Once the material has passed the primary crusher the fragmentation size will be fairly consistent and promote consistent throughput of the plant or mill. In late 2015 a team was conducting a reassessment visit to a mining site where we had conducted the original assessment the previous year. Though many recommendations had been implemented some had been so recent they had not resulted in the expected improvements. Several of our discussions kept returning to the impact fragmentation has to both the individual components of the mining cycle but also the effects compounded throughout the end to end process. Let’s move on to the big picture before we zoom in on any specific operation. To get from native solid rock in the ground to a concentrate or a saleable rock product we have the same steps from one end of the chain to the other. We start with a good geological understanding of the rock type, characteristics and structure to design a program to drill and blast the rock. The height of the bench is relevant to the annual production requirements and the specific digging equipment models best sized to make that production possible. The equipment selection influences the bench height which has a minimum and maximum hole diameter to maintain a safe blasting operation. The diameter of hole burden and spacing all contribute to a good distribution of explosives in the rock mass that maximize the fragmentation and preconditioning of the rock when blasted. The timing and sequencing of hole initiation will yield a fragmentation ratio and diggability factor. Fragmentation size adjustments will change the meters drilled per cube and the explosives consumption will change accordingly. Drill cost is measured by meter drilled so a direct relationship exists between cost and fragmentation sized achieved."

Jan 1, 2017

By Franz Deix, Bernd Braun

A sensitive portion of Section U 6/3 of the Vienna, Austria subway system required construction of two single-track tunnels under a telecommunications facility, where strict ground settlement limitations had been set. Local geology, hydrology, and site constraints led to the decision to use the New Austrian Tunneling Method (NATM) supplemented by compressed air and partial dewatering. In addition, ground freezing was used, as the tunnel would pass through alluvial layers beneath the facility, with a cover of as little as 1.5 m. Laboratory testing and two in situ test fields were used to collect frozen soil data so that the freezing scheme ensured minimal heaving magnitude.

Jan 1, 1987

By William Gleason

For the first time in many years, the Liebherr Group chose to host its annual conference for the international construction trade press in the United States. The reason for the move is simple ? mining. Like other large corporations, especially those in the construction fields, Liebherr felt the effects of the global economic crisis that began in 2008. The slowdown in the housing market was especially hard on Liebherr?s mobile crane and earth moving divisions. The mining division, however, while affected by crashing commodity prices that led to cancelled orders and the loss of financing for some customers, was not battered as badly as the other divisions. And now, with the price of commodities once again on the rise, it seems that it will be Liebherr?s largest machines that lead the family-owned company to better days. ?We can report that our generally optimistic view during the crisis has proved adequate,? said Joachim Janka, president of Liebherr mining equipment, at the conference in Williamsburg, VA, just down the road from the company?s mining truck division global headquarters in Newport News, VA. ?Since the third quarter of 2009, our mining equipment activities have been recording once more a strong and steady demand. This has already yielded a substantial increase in market shares for our product lines of large mining shovels as well as for mining trucks.?

Jan 1, 2011

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By James Humphrey

There is a natural resistance to change in any form. When it comes to implementing a game-changing technology like autonomous haulage on an operating mine site, the resistance can at times appear insurmountable. Whether based on real information or misguided preconceptions, it?s essential that we don?t underestimate the effort it will take to overcome this resistance, while clearly recognizing when it?s worth the effort. These realizations did not happen overnight for sites where autonomous haulage has been implemented. Nor did they happen overnight for manufacturers of autonomous mining equipment. Caterpillar, for example, began building toward autonomy more than 30 years ago and had a truck operating in the mid-1990s. Lessons learned during those early years led to the realization that there was much more to be learned ? not just about the machines themselves, but about the systems and knowledge that must be in place for a successful implementation. Working closely with customers, initiating real-life demonstrations on mine sites, having discussions with regulatory agencies and other stakeholders ? these and many other activities were necessary before autonomy could be fully and successfully launched. After decades of effort, Caterpillar?s first official commercial autonomous mine site went to work in 2011 in Farmington, NM.

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960