Search Documents

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By L. S. McNickle

[Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part.]

Jan 1, 1961

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By N. Nemeth

The filter is an apparatus designed to hold the filter medium. At such a medium takes place the entire liquid-solid or gas-solid separation process. Hence, the medium is really the essence of filtration. Yet, the medium, an originally clean porous substance with trapped solids in it, is perhaps the most neglected part of filtration research. Basically three problems prevail at the medium: 1) Penetration of solids and their blinding of the medium and the influence of such blinding on the resistance to flow. ii) The behavior of the medium in long term repetitive filtration. iii) The filter effect phenomenon whereby the flow rate on filtering an apparently clear liquid through a medium decreases with time. This study undertakes to investigate these fundamental processes.

Jan 1, 1968

By A. Moergeli, Philip Sander, John J. Reilly

"Estimating and managing the costs of complex infrastructure projects – in the planning/design and construction phases, for both owners and contractors – has been a challenge for decades. The more complex and technologically advanced the project, the greater the uncertainty, including potential risks that are important to owners and contractors, such as:• Cost risks to owners – meeting budget and schedule, maintaining public credibility.• Cost risks to contractors – profit, consequences of loss, impacts to reputation/future work.This concern has been addressed in various ways by the underground construction industry for some time (Reilly, 2001). In particular, while significant advances have been made in cost estimating for the planning and design phases (Reilly et al., 2004), that are important to agencies and political decision-makers, it is not apparent that these advances have been widely adopted for construction cost estimates. The reasons for this may relate to lowbid considerations – any method that tends to increase the contractor’s cost estimate, by including risk or likely costs, could lead to an erosion of the contractor’s competitive position – if others are not similarly required to include such costs.Different cost estimating methods produce different levels of information. Specifically, there is a large difference in the character and depth of information if a deterministic (quantities times price plus a contingency) and risk-based cost methods are used. It is this difference in character and depth of information that is the reason that risk-based cost estimating has potential value for owners and contractors. Figure 1 presents hypothetical cost results from deterministic and risk-based methods and illustrates some of these differences.In Fig. 1, the results for deterministic and risk-based cost estimates are given related to the potential profit or loss for a typical project. As is evident in this example, there is significant potential for costs to be realized that are higher than the proposal/bid value estimated using a deterministic approach, with a 15 percent probability of a loss. There is a 30 percent probability that the project will have a reduced profit. There is a 55 percent probability that the project will return a good profit. Using a risk-based approach, it is possible to better recognize this potential outcome in the bid phase and, as a consequence, develop a strategy to:"

Apr 1, 2016

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By Y. C. Kim

Using an exhaustive data set of Walker Lake, four different kriging techniques plus the inverse distance squared weighting were compared with regards to each one's performance in accurately estimating the block grades. The North-West quadrant of the Walker Lake data area was used because of its extreme variability of values and its distinct contour of the values. There were 1900 exhaustive data points in the selected area from which a total of 121 samples were drawn following the sampling strategy given in Isaaks and Srivastava (1989). The average of 5 x 5 exhaustive data points was treated as the true, known block grade. A total of 780 blocks, each block corresponding to the average of 5x5 exhaustive data points, were then estimated using the 121 sample points. The resulting estimates were then compared with the true known values to determine each technique's prediction performance. For this particular portion of the Walker Lake and for the given sampling strategies used, the obtained results for the global estimation are mixed. For the variable U which is much more variable, the rankings are; 1) Jackknife Kriging (JK), 2) Indicator Kriging (IK), 3) Inverse Distance Square weighting (IDS), 4) Ordinary Kriging (OK), and 5) Log-Jackknife Kriging (LJK). For the variable V, the results are; 1) OK, 2) IK, 3) JK, 4) LJK, and 5) IDS. When we apply several cutoff grades to the estimates to determine the conditional mean grades and tonnage, the above rankings generally get shifted around. Two exceptions to these cases are; a) UK for U and b) IDS for V. These two consistently ranked at the bottom.

Jan 1, 1995

By J. Payton

Public Service Company of Oklahoma began burning sub-bituminous coal in December, 1979. Initially PSO had a single source coal supply from Jacobs Ranch Mine, and in 1982 added deliveries from Clovis Point mine. Both are Powder River Basin (Wyoming) coal mines. In 1986 PSO began burning Oklahoma coal to meet Oklahoma's 10% native use law. PSO experienced random s lagging during certain blends of these coals. PSO installed a boiler performance system to help control the slagging problems from the various coal blends, to improve boiler efficiency, and increase total coal consumption.

Jan 1, 1990

Asgco’s design of the Arrowhead Ceramic Lagging provides solutions to problems experienced with conveyor belt slippage around the drive pulley and severe wear problems on snub and bend pulleys. Asgco has developed a range of pulley lagging from ceramic, drive rubber and non-drive rubber lagging that is available in abrasion-resistant SBR and MSHA grade rubber for conveyor pulleys from slow belts all the way through to high-speed, high load belts. There is a growing need for a maintenance-free and reliable pulley lagging to ensure conveyor belts run to their highest efficiency.

Jan 1, 2006

By C. R. Montgomery

Coal companies in order to supply their customers En the metallurgical market, both home and abroad, must be able to control their production in order to meet carbonization specifications over and above those of the proximate analyses which has been the prime consideration of purchases in the past. It is the purpose of this paper to review in brief some of the tests used and give data to show the application of such as it applies to the customers needs. It is now recognized that coal is not homogeneous in any of its properties and an amazing fact is that it has been used for so long a time as the principal raw material for the manufacturing of coke without more emphasis having been placed on the variation between coals; yes, even from coals in the same seam at different geographical locations, Recently Kuchta and Clendenin pointed this fact out In a study of the(1) carbonizing behavior as related to chemical and plastic properties of Alabama medium volatile coal.

Jan 1, 1962

By E. M. Frizzell

In an effort to economically and efficiently enhance the erosion control aspects of present surface coal mine reclamation practices, the US Bureau of Mines has recently completed a two-phase research program wherein irrigation strategies and equipment developed under the first phase were field tested on three surface coal mine sites. The fundamental basis for the use of irrigation as a reclamation tool is to provide the plant moisture requirements as a supplement to prevailing natural precipitation, and thereby support the natural growth of drought-hardy native vegetation. Portable solid-set irrigation equipment and several irrigation strategies were tested on large 6-ha (15-acre) sites in Montana, Wyoming, and New Mexico. Results of these tests will be presented which include daily irrigations, precipitation levels, soil moistures, climatic data, and density cover and biomass of the native plants.

Jan 1, 1987

By Maurice L. Madden

An investigation was undertaken for a ground water discharge plan for the Chino mining complex near Hurley, New Mexico. Operations which impact ground water include dump leaching, storage reservoirs, and tailings seepage. The investigation included both hydrogeological data collection and laboratory analysis. A conceptual understanding of surface water and ground water was then developed. Surface water and ground water models were used to match existing conditions and predict the impact of operational modifications. The study concluded that runoff and resulting leach reservoir overflows were primarily responsible for the ground water degradation. Tailings seepage represents a smaller part of the impact.

Jan 1, 1984

By Pramod C. Thakur

Coal is a major source of energy in the world today and will, undoubtedly, continue to be so for the next few centuries. Naturally, a great number of studies has been made of its physical and chemical properties. Unfortunately, the work on technical properties which influence the mining of coal and the consequent yield of inflammable gases and respirable dust particles has not progressed at a comparable pace. Coal is a brittle material. Irrespective of the mechanism of breaking coal, some dust is always produced. In mining parlance dust is defined as solid particle, smaller than 100 microns (micron = 10-6 meter), in size Coal dust, when raised into a cloud, creates two well known hazards in mines, namely, the coal dust explosion and Coal Workers' Pneumoconiosis (CMP). The latter is, perhaps, the greatest environmental hazard in U.S. coal mines today. In this context it is not only natural but also necessary to investigate the proneness of a coal seam to respirable dust production. It has been established that the amount of dust produced is a function of two groups of variables (1), (2), viz. (1) Material dependent variables, e.g., moisture content, compressive strength, hardness, etc. (ii) Breaking mechanism dependent variables, e.g., type of machine, depth of cut, etc.

Jan 1, 1973

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By E.C. Jong

Resumen ¦ Un sistema de comunicaciones “a través del suelo” (TTE) comercial y disponible fue evaluado en una mina de carbón subterránea en la zona Este del Estado de Kentucky. Este estudio de campo fue realizado como parte de una evaluación multisitio mayor de sistemas TTE disponibles. La mina detallada en este estudio se encontraba paralizada al momento de la evaluación, lo que proporcionó la representación más cercana a la realidad del medio ambiente en una mina luego de una operación de cierre. Para este estudio se probaron las comunicaciones superficie a subterráneo y subterráneo a superficie. El despliegue estándar del sistema TTE usando los procedimientos recomendados por el fabricante logró obtener comunicaciones claras y nítidas entre el socavón y la superficie. Otras disposiciones de las unidades arrojaron resultados mixtos. Existen planes para examinar más los fenómenos observados en esta mina.

Apr 1, 2016

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980