Search Documents

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By Warren C. Gerler

An overland belt conveyor system is installed for only one reason to save money. It must pay its way on a ton-mile basis over a stated period of time, and do so in competition with other forms of transportation. Such a system with its economies has recently been installed at Simco-Peabody's mine near Coshocton, Ohio by Link-Belt Company. Three miles in length, this system carries coal from open pit and underground mining facilities to the Conesville Power Plant of Columbus & Southern Ohio Electric Company. The coal was formerly trucked from the mine direct to the power plant; but over the years the mining operations have moved progressively farther and farther from the plant, making the over-the-road hauling distance correspondingly greater. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. The majority of the coal is recovered by conventional strip mining. Some underground mining` is performed by the high wall method.

Jan 1, 1963

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

By J. C. Weimer

The goal of Bethlehem's mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By S. L. Bessinger

In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross-section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Headlosses in mine entries are calculated using Atkinson's Equation (1). [H = (English) H = (SI) (1)] where H = pressure ,loss, in. of H20 (Pa) K = friction factor, lbf min2/ft"4(Kg/m3) P = perimeter, ft. (m) L = airway length, ft (m) Q = airflow quantity, ft3/min (m3/sec) A = flow cross sectional area, ft2 (m2)

Jan 1, 1987

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation utilizing large draglines, trucks and shovels, tractor-scrapers, and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity, and distance, and to provide historical information for planning the most efficient and economic use of each equipment type in the mining operation. This report explains how the work order system was initiated, what data is tracked, and how the data is utilized for equipment and project scheduling.

Jan 1, 1994

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By J. F. Cornelsen

Wheel loaders are currently being used in many mining applications for a variety of reasons. While they sometimes provide the lowest loading cost, a primary advantage of the wheel loader versus other loading systems is the increased versatility and mobility inherent in a wheeled vehicle. The advent of large wheel loaders with much greater digging capability enhanced wheel loader usage in severe loading applications. To match these severe conditions, machines offered today were designed to work in these rocky conditions. Soon after the introduction of large wheel loaders into rocky conditions, however, it became apparent to many users that tire costs could at times account for up to 50% of total hourly operating costs on large wheel loaders. In some applications, tire costs alone pushed wheel loader economics beyond the economic feasibility for these jobs, prohibiting their use. In an effort to combat high tire costs, several attempts have been made to put fast moving steel around the tires to provide a strong interface between vehicle and ground. Some earlier attempts involved wrapping tracks around tires. Mechanical difficulties with these systems limited their customer acceptance. Subsequently, the development of protective tire chains came into favor. While tire chains offered added protection to the tires, the cost and maintenance of the chains remains a problem in 1972, the Dystred arrangement was announced for usage on a 6 cu yd wheel loader from Caterpillar Tractor Co. (See Figure 1). The Dystred offered the advantages of greatly increased tread life over conventional tires, as well as resistance to tread puncture in most situations. The arrangement basically employed a track system similar to that used on track type loaders. Pin and bushing wear often caused high hourly operating costs and excessive machine downtime. In addition, the connection of shoes through the use of links, pins, and bushings forced a limitation on too speed of the vehicle.

Jan 1, 1976

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By R. J. Roman

During the refining of primary magnesium metal: a spent flux (sludge) is produced which is considered a dangerous waste by the Washington State Department of Ecology. Four years of research, testing and marketing has identified two beneficial markets for the spent flux: 1) as a fertilizer and soil admendment as a result of the material's high potash and nitrogen content and its high lime equivalence and 2), as a roadway deicing agent to clear roads of ice and snow as a result of both the salt content and the flux containing chemical compounds which exothermically react with water.

Jan 1, 1988

By John Ward Smith

Dawsonite bearing oil shale of Colorado's Green River Formation offers a unique and vast (6.5 billion tons of Al2O3) resource of easily extractable alumina. The processing methods required by the thermal reactions dawsonite and its oil shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary Federal oil-shale withdrawal appear less solvable.

Jan 1, 1980

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

By Ming-yi Zhang, Zhong-nian Yang, Xiao-ming Guan, Quan-wei Liu

"In slurry balanced shield tunneling, how to ensure the safety of construction and to reduce the influence on the environment has arisen wide attention of scholars both at home and abroad. But now it is still in the stage of experience as to the instability mechanism of the slurry shield tunneling excavation and its stability analysis. Based on the large-diameter model tests and FLAC 3D, the effect of the different waterhead (non-water, 0.9m and 1.1m) on stability of excavation face of slurry balanced shield is investigated, and the stability mechanics is proposed. The results show that: waterhead heights play an important role on excavation face instability features of slurry balanced shield in sandy stratum, Regarding the different waterhead heights, the development mode of the excavation face instability features can be divided into non-water mode, lower-waterhead mode and higher-waterhead mode; soil arching is existed in the process of excavation face instability, the settlement of ground lags behind excavation face failure, the soil arching will block or eliminate the effects of ground settlement; excess pore water pressure need to be considered besides earth pressure and hydrostatic pressure when the supporting force is calculated. INTRODUCTION With the development of the society, for the cities all over the world, the exploitation of underground space has become an important measure to solve the problems about population, resources and environment and an important way to heal the city syndrome and implement the sustainable development strategy of city. Constructing shield tunnel with large diameter is the major trend for development of tunnel construction (Yin, 1999). Instability of excavation face caused by relief of shield soil stress is still one problem that needs to be solved (Xiang, 2001). How to reduce the effects of construction on surrounding environment? How to accurately determine the instability of shield excavation face and to effectively and reasonably select the supporting force? These are the crucial problems which need to be solved during shield construction."

Jan 1, 2016

By Donald W. Gentry

Introduction The mining industry is perhaps best characterized by the numerous and abnormally high risks associated with the business of mining and by its most basic assets - ore deposits, people and technology. At the most fundamental level, it is the quality and effective utilization of these basic assets that determine a mining company's ability to compete efficiently in the international market place. The gold industry has received much attention in recent years and especially in recent months, for good reason. This commodity serves as an excellent platform for the subsequent discussion of these three basic assets and their role in mining's future. Facets of the gold industry The fate of this noble metal in recent times illustrates some of the various risks associated with the mining industry and the importance of high-quality assets, whether they be ore deposits, people or technologies. The following comments pertaining to the gold industry help place proper focus on subsequent discussions. All monetary amounts given are in US dollars. Throughout 1997, falling gold prices broke record after record: first hitting three-year lows, then a 12-year low in July and finally an 18-year low at year's end. From Jan. 1 through Dec. 31, 1997, the price of gold fell by more than $2.57/g ($80/oz), or some 22%. The decline in gold-mining profitability and stock prices was even more dramatic. At the beginning of 1997, the 20 largest gold producers in North America had a market capitalization of approximately $44.5 billion. At year's end, this market cap had fallen to $26.2 billion, a reduction of 41%. The total market cap of all the world's gold companies fell from $71 billion to $46 billion, a 35% drop (Serwer, 1998). Analyses suggest that, at a spot gold price of $9.65/g ($300/oz), only one, or possibly two, North American gold-producing companies can make money when break-even or "total costs of production" are considered. While strong hedge positions mitigate this situation in the short term, clearly, this is an industry in desperate straits. For example, write-downs for North American producers in 1997 were approximately $2.5 billion. Speculative short positions in 1997 were near historical record highs and generally exceeded long positions by factors of 9:1 or 10:1. Much of this is driven by some US commercial banks, hedge fund managers and commodity speculators who can significantly move gold prices sharply over short periods of time by selling gold they do not own in the expectation they can buy it back at a lower price before they have to deliver. These signifcant short positions are likely to continue as long as central banks are willing to sell or loan gold to financial institutions that in turn make the gold available to speculators who hope to capitalize on price fluctuations. The Far East accounts for approximately 26% of the annual demand for gold. Including India, the region accounts for 43% of total demand. More than 85% of the physical demand for gold is for investment jewelry in Asia and the Middle East. This demand is extraordinarily price sensitive. The fairly recent turmoil in Asian markets and economies, combined with currency devaluations throughout the region, have made gold more expensive (30% to 50% in local currencies) for those peoples most likely to treat gold as a safe investment haven. Higher interest rates also have reduced the amount of money they have to spend on consumer goods such as jewelry. All of these recent Asian events are deflationary in nature. Deflation, if coincident with rising unemployment, could result in significant dishoarding of gold. There is one key fact to remember when analyzing

Jan 1, 1999

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982