Search Documents

By R. E. Mason

Shotcrete has been used for approximately 20 years to facilitate tunnel excavation through poor ground. Early examples of such usage in North America include the recuperation of the Granduc Mines access tunnel in Northern British Columbia, and similar work performed in the Carley V. Porter and Big Walker Tunnels in the United States. Mining companies such as Craigmont Mines in B.C. and Hecla Mines have used shotcrete in their workings for the past ten years. Shotcrete is now a widely utilized fool in the mining and tunnel construction industries in North America, but the accumulated experience is too limited for many to fully appreciate the capability of shotcrete to control ground movements and to understand the limitations of this tool. It is common, for instance, to use shotcrete to "bridge the gap" between rock bolt-supported and steel-rib supported ground and to avoid the use of shotcrete in water-bearing ground. Shotcrete can, and has been, used economically and practically under most severe ground conditions.

Jan 1, 1976

By R. C. Emmett

In extractive metallurgy, separation of insoluble solids from solutions is an important economic factor in almost all flow- sheets. This separation step can employ sedimentation, filtration (vacuum and pressure), or centrifugation. Since practically all systems require a relatively complete separation, multiple unit, countercurrent thickeners or vacuum filters are generally used.

Jan 1, 1974

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By Peter J. Huck, Yoginder P. Chugh, M. Jennings

INTRODUCTION Large areas of the United States coal reserves have been undermined by room-and-pillar mining over the past century. These abandoned mines generally cause subsidence of the ground surface many decades after mining. Reports from England (1) where there is a longer history of room-and-pillar mining indicate that mines abandoned two centuries ago may still be causing subsidence, and causing surface destruction to urban areas or farm lands that have been developed in the interim. The devastation wrought by subsidence, both in terms of property loss and societal disruption is enormous. The authors discuss here the methods by which subsidence in abandoned mines may be controlled. Two distinctly different subsidence control technologies have been developed in the U.S. for abandoned coal mines. These are referred to as (1) Point Sup- port methods, and (2) Areal Backfilling. As the names imply, point support methods are used to protect individual structures, or even individual foundation elements of structures, whereas areas backfilling techniques may be applied to protect entire neighborhoods or urban districts hundreds of acres in extent. Both point support methods and areal backfilling have specific sub-categories of techniques that may be applied under different conditions as appropriate. POINT SUPPORT METHODS Point support methods are characteristically employed by civil engineers chartered with the design of a new structure or the protection of an existing structure. The subsidence control measures are only a part of a larger project, the safety of which must be assured to a degree of near certainty. The costs of point support methods involve a large number of bore-holes and the use of expensive materials in relatively small quantities. There exist several dozen point support methods, which operate either to support the underground cavities, controlling subsidence, or to isolate the structure from the effects of subsidence if it should occur. The latter methods usually involve deep foundations through the mine opening supporting the structure on the underlying strata. Our concern will be with the former method to support underground cavities to prevent subsidence. Gravel Columns and Associated Methods Gravel columns may be placed in the mine opening using the methods shown in [Figure 1]. Boreholes are drilled through the mine strata, and gravel poured down the borehole to form a pile on the mine floor. When the tip of the pile contacts the mine roof, it is rodded down to spread the pile, and permit additional gravel to be placed. The objective is to place as much gravel as possible in the mine opening, and to achieve firm contact with the mine roof. The gravel pile acts to reduce subsidence by three mechanisms. The filling of a significant fraction of the open mine volume reduces the amount of potential subsidence simply by killing open volume within the mine. In effect, the extraction ratio has been reduced by introducing the volume of gravel. The toe of the gravel pile abuts against nearby pillars, providing lateral support and protection against pillar deterioration. In effect, the height of the pillars has been slightly reduced by burying their lower portions. Finally, some direct support is provided to the roof strata, reducing the roof span and enhancing stability. The gravel column method may be used in a variety of applications, and with materials other than gravel. For example, gravel columns may be placed in a close line around the perimeter of the building to form a continuous gravel wall. The interior of the site may then be completely filled with sand, slurry or other material. Alternatively, a lean concrete may be used in place of gravel, so that the piles achieve significant structural capacity. The grout column, shown in [Figure 2], begins with the installation of a conventional gravel column which is placed around a grout pipe that extends through the borehole into the mine opening. When the gravel column is in place, portland cement grout is injected in stages. At each stage, sufficient grout is injected to fill the interstices in the gravel to build a column perhaps two meters in diameter and a meter tall. The group pipe is then raised one meter, and after the previously injected grout has set, the next stage of grout is injected. The process builds a column of grouted gravel to the

Jan 1, 1982

By Peter Zhang, Mark Van Dyke, Ted Klemetti, Morgan Sears

Room-and-pillar mining is a mining method used in the United States to extract coal from underground, and pillar recovery is widely practiced for maximizing coal recovery and mining economics. Under certain conditions, room-and-pillar mining can create high stresses in coal pillars resulting in a coal outburst. These outbursts represent one of the more severe safety hazards in underground coal mines, potentially causing injuries and fatalities. Over the past ten years, coal outbursts have resulted in three fatalities in U.S. room-and-pillar mines. Though coal outbursts generally occur under deep cover, they are more likely to occur during pillar recovery and under multiple-seam mining conditions. Coal outbursts are generally associated with strong roof and floor and heavy loading of coal pillars, but it is difficult to predict whether, where, and when they will occur. In this respect, risk management provides a proactive tool to prevent coal outbursts in room-and-pillar mining by identifying mining areas with high risk of outburst and mitigating the risk accordingly.

Apr 26, 2022

By James P. Connell

The Berkeley Pit of The Anaconda Company is located on the southeast slope of the Butte Hill, the legendary "Richest Hill on Earth," and is one of the largest pit operations in the world completely dependent on truck haulage. Through October 31, 1968, the Berkeley stripping and mining operations have moved more than 442,589,000 tons of material. Present scheduled production is at the rate of 260,000 tons per day, with a record quantity of 306,900 tons having been hauled on September 23, 1968. Although the Berkeley Pit has been in production only a little more than ten years, it has been the proving ground for many of the presently used large trucks. Beginning with the original R. G. LeTourneau 75-ton electric truck in 1960, Unit Rig 85- and 100-ton electric drives, Haulpak 65- and 105-ton electric drives, and Caterpillar 100-ton electric drives have all been tested under production conditions. In addition, engine development has kept pace with both 1000-hp diesel and 1100-hp gas turbine engines now under test. As the size of the Berkeley operation has grown, the truck fleet has changed in size and appearance in order to maintain economic mining costs. The original fleet consisted of forty-three 36-ton trucks with conventional mechanical drives. The present fleet is made up of eighty-nine trucks: nineteen 85-ton Unit Rig electrics with 700-hp diesel engines; sixty-nine 100-ton Unit Rig electrics with either 700- or 1000-hp diesel engines; and one 100-ton Unit Rig electric with an 1100-hp gas turbine engine.

Jan 1, 1969

By Walter M. Chapman

The National Lead Company operates its MacI tyre Development at Tahawus, New York for the production of ilmenite and. magnetite. The heavy ore of titanium and iron is mined from the open pit mine at an average rate of 7,000 tons per day, and the development waste is removed at an average rate of 10,000 tons per day. The mine working benches are spaced, at 35-foot vertical intervals, and 6 ½ inch blast holes are drilled 39-feet deep with 18-foot burden and spacing by down-the-hole drills. Waste is loaded with a 6 yeard shovel and ore with 2 ½ yard shovels into 22-ton rear dump trucks. A good account of the history of MacIntyre drilling and. blasting was presented to this assembly two years ago, by F. R. Jones. (1) Most of the blasting since the start of the mine in 1941 was done with 90% gelatin dynamite until 1955, when relatively insensitive canned blasting agents were adopted.. In 1956, 9-inch blast holes drilled with down-the-hole drills. In 1956, also, the first experimental trials of prilled ammonium nitrate fertilizer and fuel oil (hereafter called fertilizer) was made following the lead of Cleveland-Cliffs operations in the Hibbing district. Since that trial did not, as some local skeptics predicted, make grass grown on the bluff, but resulted in a well-broken shot, further tests were conducted in dry holes. I Observations of those tests indicated that the fertilizer did its share of the work. If anything, it produced better fragmentation than the normal load di in neighboring wet holes.

Jan 1, 1958

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By T. Schrauf, J. Scott

"INTRODUCTION Cyanide heap leaching of gold ores in areas with extremely low winter temperatures requires special considerations to prevent freezing of the leach solution. Factors that impact the solution temperature include ore temperature at the time of stacking and during operation, burial of drip irrigation lines, use of geomembrane covers, and heating of the leach solution. Thermodynamic modeling was performed to simulate expected ore and solution temperatures under different operating strategies for Kaminak Gold’s Coffee Gold project in the Yukon Territory. Mean monthly temperatures at the site ranged from a low of -22.5oC to a high of 13.6oC, while in situ ore temperatures ranged from -0.5 to about -1.5oC. The modeling results were used to optimize the operational parameters and indicated that a combination of drip line burial and heating of the leach solution during the winter months was required to maintain solution temperatures above freezing during the initial years of stacking, although as the size of the heap increased, heating was no longer necessary. MODELING OBJECTIVES The successful operation of a cyanide heap leach under extremely cold winter temperatures requires the implementation of operational strategies to prevent freezing of the leach solution and the ore within the heap. Thermodynamic modeling of the heap provides the means to quantify the effectiveness of these different operational parameters on maintaining the required operating temperatures to avoid freezing within the heap. The operational parameters that were evaluated with the model included: • Burial depth of irrigation lines to prevent freezing during the winter months; • Variation in the temperature of the applied leach solution (to simulate heating of recirculated solution); • Variation in the rate of irrigation including seasonal variations between winter and summer months; • Seasonal versus year-round stacking of ore (to simulate the impact of the initial temperature of each ore layer as it is stacked); • Seasonal versus year-round crushing and stockpiling of ore, including the option to stockpile ore on the leach pad in the winter (i.e. stack but not leach fresh ore in winter); • Start date for seasonal stacking; • Variation of the heap geometry over time (both vertical and lateral expansion) and the associated heat storage within the heap; • Use of thermal covers (gravel or geomembrane) over the ore during the winter months; and • Effect of crush size on heat loss during crushing, stockpiling and stacking."

Jan 1, 2016

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By Rodney L. Stone

As part of an overall laboratory and plant test program to determine mixing and other techniques relating to the more economic use of bentonite as an iron ore pellet binder, a settling test was developed for measuring the bentonite content within a pellet or within a batch of pellets. Between pellet batches, each containing a different level of bentonite, the dry fracture load is directly proportional to the bentonite content between pellets of the same batch, however, the fracture load is inversely proportional to the bentonite level; this is explained by a negative correlation between a pellet's size and its bentonite content and the fact that larger pellets can withstand a higher fracture load than the smaller.

Jan 1, 1968

By J. R. Boldt, C. M. Kleemann, V. N. Mackiw, B. Meddings, J. A. MacLellan, E. J. Maney, D. E. Halter, D. J. I. Evans, J. Honkasalo, M. F. Dufour

The technology employed in the processing of nickel- and cobalt¬bearing ores is a continually developing process for utilizing the natu¬ral resources available at a given time. Most of the nickel-bearing ores of commercial importance fall under the category of sulfide or lateritic ores. While the occurrences of both types of ore have been known for over a century, until 1960 sulfide ores largely from Cana¬dian mines have constituted the chief source of production for com¬mercial nickel in the Free World. Sulfide ores are readily amenable to some physical means of concentration, but the lateritic ores are not readily concentrated, and to compete economically with the sulfide ores only the high-grade garnierite ores (a type of lateritic ore) found in New Caledonia were processed to any great extent up to the time of World War II. Around 1960, a gradual shift in emphasis towards latetitic ores as a commercial source of nickel became evident. See Fig. 1. New discoveries of sulfide ores, usually located underground, had not kept pace with the steadily increasing demand for nickel. The lateritic ores, found near the surface of the earth, could be readily surveyed and mined. Lower cost processes were being developed for the extrac¬tion of nickel from lateritic ores and for a time it appeared that, based on pre-OPEC economics, the lower grade lateritic ores-down to 1.2% nickel-could satisfy an increasing share of the world demand for nickel. The sharp increase in the price of crude oil in the 1970s, however, slapped an economic damper on the lateritic ores. Processes for treat¬ing lateritic ores consume large amounts of energy; as the nickel industry entered its deep recessionary period in 1981-83, nickel pro¬duction from lateritic ores became less and less profitable than from sulfide ores. At the same time, new sulfide ores were discovered and brought into production, notably in Australia and South Africa. The chapters in Section 17 were prepared in 1973. Recent improvements in mineral dressing techniques since then include Inco's pyrrhotite separation process which can remove additional pyrrhotite from nickel concentrates, resulting in reduced sulfur dioxide emission from the Sudbury smelter, by some 25%. The chapters in this section dealing with nickel are grouped in line with the two broad categories of nickel ores. Starting with the description of nickel and cobalt ores in Chapter 2, Chapter 3 deals with the processing of sulfide ores, and Chapter 4 deals largely with lateritic ores. The intermediate steps to produce a suitable feed for extraction plants and refineries are similar in principle within the same categories, although dissimilar between sulfide and lateritic ores. Thus Inco in Canada employs flotation and so does Western Mining Corp. in Australia, although Inco's plants were started before World War II, and that of Western Mining only recently in the late 1960s. Treatment subsequent to the ore dressing step, however, shows some interesting differences. The earlier parts deal mostly with established and conventional practices, leaning heavily on pyrometallurgy in both

Jan 1, 1985