Search Documents

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By Mark P. Walsh

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within groundwater aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contaminantion. Since ammonia is one of the constituents of the leach solutions now being field tested, one environ- mental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laboratory experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit. Dispersion attending the flow of fluids in a porous medium is also shown to be an important factor. The effect of dispersion can greatly reduce the benefits of having a displacing cation which is adsorbed selectively with respect to ammonium. Since dispersion increases almost linearly with fluid velocity, an optimum displacement rate may exist.

Jan 1, 1979

By Cameron Dunn, Callum Fryer, Carmen Hu, Craig Sewell, Peter Stakne, Andrew Raine

The Woodsmith Project is located in north-eastern England within the North York Moors National Park. The strata contains the world’s largest known high-grade Polyhalite resource of around 2.66 billion tonnes. The Project was initiated by York Potash Limited (YPL), a subsidiary of Sirius Minerals plc., but in March 2020, a takeover was completed by Anglo American, one of the largest mining companies in the world. Polyhalite is an evaporite mineral and contains essential nutrients required for plant growth. The Polyhalite will be extracted via two deep mine shafts and transported underground from the mine site to a Materials Handling Facility on a Mineral Transport System (MTS), which comprises a high-capacity conveyor belt system located within a 4.9 m ID tunnel. In 2018, STRABAG were awarded with the design and construction of the MTS tunnel and associated infrastructure, including the high-capacity conveyor system. The scope of work consists of 300 m of open cut, 100 m SCL tunnel, 36.5 km TBM drive (originally anticipated as three separate TBM drives) along with a network of underground caverns at the Woodsmith Mine. The construction of two 380 m deep intermediate access shafts was later awarded as Amendments to the Contract. The tunnel is constructed using a Herrenknecht Single Shield TBM. As a result of how the various elements of the project have developed over time, the first TBM drive has been extended to ~29 km making it the worlds longest single heading TBM Tunnel when complete. The option of completing the entire tunnel length with a single heading TBM drive is currently being assessed by Anglo American and STRABAG. This unprecedented tunnel length requires two intermediate shafts to provide essential access and services, the first intermediate shaft is at Lockwood beck (LWB) and the second is at Ladycross (LDX). The LWB shaft has been constructed utilising the innovative Blind Boring technique never used before in the UK. This paper will explain the methodology and technical risk management associated with this technique. The authors believe that the collaborative approach between all contract partners is and continues to be the important contributor for the success of this project.

Jun 13, 2023

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

By Nick Barton, Khosrow Bakhtar

Two plate load tests of 1 m2 area were per- formed in a pressure tunnel at the Rocky Mountain Pumped Hydro Project. Reaction for the 250 tons loading in this 10.5 meter diameter tunnel was provided by deeply anchored, diverging rock bolts, eight per load frame. Pressure build up to 2.5 MPa was provided by circular flatjacks. Rock deformation was recorded at depths of approximately 0.3, 0.9, 1.2, 1.8 and 3.3 meters using axially located multiple position borehole extensometers. The tests were performed in representative units of massive shale and thin to medium bedded siltstone. Stress was built up in four equal steps to 2.5 MPa, held constant for one week for creep monitoring, then unloaded, reloaded and unloaded over a period of one day. The most deformable unit was the massive shale which exhibited 1.3 mm of permanent deformation at the surface after the first loading and unloading cycle, which included 0.36 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 2.6 mm, following a maximum deformation at the surface of approximately 3.6 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 0.4 GPa when loading, and 0.3 GPa when unloading. The thin to medium bedded siltstone exhibited only 0.17 mm of permanent deformation at the surface after the first loading-unloading cycle, which included only 0.05 mm of creep. After the second loading-unloading cycle, the permanent deformation had increased to 0.27 mm, following a maximum deformation at the surface of approximately 0.53 mm. At the maximum stress of 2.5 MPa, the tangent modulus averaged 6.2 GPa when loading and 21.9 GPa when unloading.

Jan 1, 1986

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By Nicole R. Henderson

Many mining engineering graduates enter the mining industry lacking training in mine emergency management. As a result, mining universities in the United Sates and other countries are beginning to form volunteer student mine rescue teams to train mining engineering students in handling mine emergency situations and give them hands-on experience managing potential emergency scenarios underground. In the early 1980s, the Missouri University of Science and Technology developed the first collegiate mine rescue team in the United States. For approximately 30 years, it was the only successful collegiate team until the Colorado School of Mines (CSM) started its program in 2009. Currently, there are at least five collegiate teams in the United States and one in Canada. At the Freiberg University of Mining and Technology in Germany, the goal is to adapt the Colorado School of Mines Mine Rescue Program to develop a collegiate team of its own. Currently, mining engineering students cover the theoretical basics of mine rescue in an occupational health and safety lecture and take a basic, one-day mine rescue training course at the Central Mine Rescue Station in Leipzig. The course covers the basic mine rescue topics and gives students the opportunity to experience working in elevated heat and smoke conditions while wearing breathing apparatus. This training gives students a small insight into the importance of mine rescue and mine emergency management. Collegiate mine rescue teaches students the importance of mine rescue and mine safety by giving them hands-on learning experiences before entering the mining industry.

Feb 1, 2014

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021