Search Documents

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By James Warner, Peggy Ganse, Glen Smoak, Raymond Henn, Sam Bandimere

Over the past several decades, cement-based grouts using ultrafine cement as are placement for portland cement have begun to gain acceptance as an alternative to chemical solution grouts, however the amount of information currently available on these grouts is limited. For this reason, the authors developed a field testing program to evaluate the penetration capabilities of various ultrafine cement grout mixes. The tests were conducted by injecting sand columns using different portland and ultrafine based grouts, the measuring penetration distances after applying equal injection pressure for the same time period. Results of tests performed in 1999 and 2000 are discussed herein.

Jan 1, 2001

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By Russell Barr

Strategic alignment throughout a mining organization is critical to effective strategic execution and good business performance. The alignment of strategic goals and objectives in the different operations and functions in a large global operation is a challenge facing executive management in light of legacy organizational structure and processes. An additional confounding factor in strategic alignment of acquisition and new project expansion is that mining projects and operations are frequently multi-cultural in terms of country origin as well as organizational culture. This brings together many cultures to accomplish the project or complete an acquisition (Financial Times, 2006). The mining industry presents numerous challenges to executives and mine management by the nature of the operation and organizational processes used in running it. For example, there seems to be an inherent conflict between the individual goals of the components that constitute a mineral processing operation (the mine, the mill, the smelter and the refinery), and lowest cost production of the final product. Managers of these component operations have specific objectives passed down from the corporate executives. Those site managers tend to be compensated based on throughput and perform to this main metric. This tendency to maximize throughput for an individual operation can contradict the general process flow of a best-fit solution to producing the final product at the lowest cost. In an effort to become more aligned, firms are increasingly using balanced scorecard derivatives at great cost and effort (whether internally or externally sourced) in an attempt to help with strategic alignment. Balanced score-cards have been effective in providing a good strategic scorecard to companies with some measure of strategic alignment. Many firms make this effort of using balanced scorecards. However, most firms are not strategically aligned or, at best, are sub-optimized, in terms of strategic alignment (Kaplan and Norton, 2006). The tendency in mining operations is to focus on operating individual components as optimally as possible and stretching existing assets to the best possible production rates. ?Making tons? is the common operational focus. Numerous factors underpin this focus and can affect the ability of the operation?s ability to align properly with the corporate strategy and strategic goals. Critical factors are legacy organizational structure, culture, processes and performance measurement systems. Changing anyone of these factors to affect better strategic alignment requires significant attention to managing change.

Jan 1, 2008

By G. M. Rao, P. N. Deo

Graphite is soft and easily floatable but it is quite difficult to obtain high purity concentrate at coarse sizes. Chemical treatment can produce high grade concentrate but it is an expensive process. Graphite containing plus 96% fixed carbon (FC) with coarse flakes commands high price in international market. Such graphite concentrate containing plus 96% FC was produced in Indian Bureau of Mines (IBM) by using newly developed reagent (mixture of different hydrocarbons and terpenes, IBM/D7) instead of commonly used frothers viz. pine oil, MIBC, kerosine etc. and regrinding in a special type of mill with special grinding media instead of grinding in a conventional ball/ rod mill followed by cleaning. Both the new reagent (frother) and special grinding media are inexpensive and readily available. The process is under patenting. This paper focuses application of this new grinding methodology for flake size protection, and the new reagent for selective flotation of high purity graphite.

Jan 1, 1995

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

By Harry D. Lewis

Gilsonite is a lustrous black material that can be easily crushed into a chocolate-colored powder. It is a solid but relatively soft, lightweight hydrocarbon that visually resembles the volcanic glass obsidian. It was once thought to be a type of coal, but because it is thermoplastic it melts rather than bums. Gilsonite is found in commercial quantities only in the Uinta Basin of eastern Utah and western Colorado, where it forms vertical, nearly parallel veins of varying depth, width, and length. Gilsonite from different veins has different properties, most notably variations in softening point and solubility. These differences result in its use in a variety of industrial applications. Gilsonite&apos;s earliest commercial uses were in varnishes, buggy paints, and beer vat linings. Eventually it came to be used in more than 160 products ranging from inks to explosives. It is exported from the United States to most industrialized countries throughout the world. Today, due to competition from synthetics and other hydrocarbon products, its use has narrowed to several specific industries. Although sold mostly as a commodity, current research is focused on applications for gilsonite as a value added product. Historical Overview The discovery of gold in California and the dawn of the mining era in Nevada, Colorado, and Utah around 1850 brought a wave of prospectors to the western United States. One of those pioneers, Samuel H. Gilson, is generally credited with a major role in the discovery of gilsonite. The material now known as gilsonite was discovered several times from the late 1860s through the mid-1880s. It was William P. Blake who, after receiving samples of the material, wrote a paper in 1885 describing "a new variety of asphaltum from the Uinta Mountains." He termed the material uintaite. Although Sam Gilson was not the first to discover the mineral, he was an-inventor who used gilsonite in products that he patented. It was his conviction that the substance was of great value, which caused some to refer to it as gilsonite. The term Gilsonite became the registered trademark of the American Gilsonite Co., and it continues to be in use today. When the first company was formed to mine this substance in 1886 it was named the Gilsonite Manufacturing Co. This firm acquired many gilsonite mining claims and marketed a varnish made from the material. It was the unusual properties of gilsonite varnish that attracted the attention of Adolphus Busch of the Anheuser-Busch Brewing Co. In 1889 Anheuser-Busch bought out Gilson&apos;s interests and formed the Gilson Asphaltum Co. Busch had been importing asphalt from Sicily for use in lining beer barrels and saw gilsonite as being more readily available and cheaper. Although gilsonite did not work well in this application, Busch did acquire a large number of mining claims in the Uinta Basin. In 1903 the parent firm of Gilson Asphaltum financed the building of an 85-km railroad from near Grand Junction, CO, to Dragon, UT, to haul gilsonite ore to market. Underground mining was initially centered near Dragon and then later at Bonanza, UT, as different veins were mined. The railway was abandoned in 1937 in favor of truck transportation. In 1938 Gilson Asphaltum changed its name to Barber Asphalt Co., the predecessor of Barber Oil Corp. In 1946 Barber Oil teamed with Standard Oil of California to form a partnership, American Gilsonite Co., which today has its operational headquarters at Bonanza, UT. Barber Oil investigated many new uses for gilsonite, including the making of petroleum derivatives such as gasoline. This work led to the construction of a 116-km pipeline to carry slurried gilsonite to a refinery in Colorado for the production of gasoline, fuel oil, and coke. Pipeline operations began in 1957 but stopped when the economics of competing with petroleum became unfavorable, and the refinery was sold in 1973. In 1981 Standard Oil (later Chevron) became the sole owner of American Gilsonite and remained so until 1991, when it sold its interest to Stratford Enterprises Co. of Tulsa, OK. The companies have since been merged and now operate under the name American Gilsonite Co. with headquarters in Salt Lake City, UT. American Gilsonite continues to be the world&apos;s largest miner and supplier of the mineral. The American Asphalt Association was formed in 1902 by former stockholders in Gilson Asphaltum. This company mined various gilsonite claims until it was dissolved in 1953 and its properties were sold to American Gilsonite and Gordon S. Ziegler and Associates. The Utah Gilsonite Co. was established in 1920 and mined several claims until 1952, when its holdings were sold to Gordon Ziegler. Several other gilsonite mining ventures have been pursued in Utah, although they were significantly smaller in scale than those described above. There are currently three companies which mine gilsonite resin in Utah. They are American Gilsonite Co., Ziegler Chemical & Mineral Corp., and Lexco.

Jan 1, 1994

By Ralph W. Barbaro

In the mineral industry, the objective of a mining venture is to extract, process, and market a mineral commodity in such a manner that the profit of the venture is maximized. In a mining venture, a company normally has control over mine production scheduling, the selection and location of processing facilities (mineral beneficiation plants, smelting plants, refineries, or blending facilities), processed ore blending, and the selection of markets. The flexibility of the above factors provides many alternatives to satisfy the needs of each market with regard to quantity and quality of ore. The purpose of this paper is to present a mathematical model for determining the alternative that yields the maximum profit. Production planning is generally concerned with the best utilization of fixed resources, more specifically, with the determination of production and inventory levels to meet fluctuating demand requirements. A mine can be any source of ore such as an entire mine, a production unit within a mine, or an independent supplier. The objective of production scheduling is to determine the times at which each mine will be used and to allocate a required level of production. Production planning and scheduling problems are intimately associated with the location of new and existing mines and processing facilities. Although the location of the mines is usually fixed, there can be considerable flexibility in locating new processing facilities, in the selection of the processing plant, and in blending the ore before and after processing.

Jan 1, 1983

By Brian Fulcher

While tunneling in Europe has been a tradition for centuries, many companies and countries have embraced tunnel innovation with considerable vigor and creativity. Indeed, local needs and site conditions have provided the initiative for improved means, methods, materials and equipment to complete progressively more challenging projects. Many recently completed tunnels have expanded tunneling technology and contributed to the development of highly specialized and productive equipment ? such as the mixed-mode tunnel boring ma-chine (TBM) presently in operation at the SOCATOP A- [ ] 86 road tunnel and the high-pressure slurry TBMs for the Westerschelde Tunnel in the Netherlands and Hollandsas near Malmo, Sweden. This paper describes some of the key technologies employed by European tunnel builders and designers including the New Austrian Tunneling Method (NATM), advanced earth pressure-balanced (EPB) machines, pres-sure-faced (slurry) tunneling machines as well as ?hybrid? or mixed-mode TBMs. While these tunneling methods and equipment generally involve significant equipment investment, they may also involve highly trained, experienced and specialized tunneling and support crews as well as materials and tools specifically developed to supplement or complement tunneling performance. For example, mechanized pipe arch placement substantially improves ground support measures and NATM advance and on larger tunnel cross-sections.

Jan 1, 2007

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120&apos;) below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300&apos;) above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820&apos;) of horizontal tun-nel, averaging 3.6 m x 3.6 m (12&apos; × 12&apos;), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13&apos;) long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10&apos;) diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005