Search Documents

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By Warren D. Stanford Stanford

Introduction The Sleeper mine is a near-surface gold mine located in a remote area 56 km (35 air miles) northwest of Winnemucca, NV (Fig. 1). The deposit was discovered in 1984 by an Amax exploration geologist. Favorable drilling results led to feasibility studies and metallurgical testwork. Final evaluation of the mine potential proceeded very quickly. The project received Amax board approval in July 1985. Eight months later, the process plant was fully operational. The first gold ($1 million) was shipped one month later, in March 1986. Total plant capital was $27 million. Payback was achieved in six months. The Sleeper mine was expected to produce 1.6 t (53,000 oz) of gold and 1.3 t (41,000 oz) of silver annually. However, the ore body exceeded all expectations. Production for the first 10 months of operation amounted to 4 t (128,000 oz) of gold and 2.9 t (94,000 oz) of silver. Direct cash operating costs are in the $1.77/g ($55 per oz) range. Amax is actively conducting exploration nearby for additional reserves to extend the mine's life. (See update on page 242.) Geology The Sleeper gold deposit is located on the northwestern flank of the Slumbering Hills and in the Awakening Mining District. Rocks exposed in the vicinity of the deposit are interbedded siltstones, sandstones, and limestones of Triassic age. They are overlain by latite lava flows and tuffs of Tertiary age. Dikes and sills of latite and andesite intrude the sedimentary rocks. Quaternary deposits of mostly sand with minor gravel and clay cover a pediment containing the gold deposit. The sedimentary and volcanic rock units have been transsected and offset by extensive north- northeast trending faults and less abundant northwest trending faults. Both fault systems fractured and prepared the ground for subsequent invasions of mineral-bearing hot spring geothermal waters. The hot spring systems produced widespread hydrothermal alteration and gold mineralization at silicified centers near feeder fault structures. The deposit is hosted by siltstone and latite that have been hydrothermally brecciated. The main breccia is elongated north-northeasterly. The hydrothermal breccia zones appear to dip steeply to the west. Gold mineralization consists of native gold and electrum deposited in two or more high-grade quartz-breccia veins. Lower grade gold mineralization occurs

Jan 4, 1987

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

There are multiple stages in a mining operation that a mining engineer has to draw polygons to be used as operation guidelines. These polygons are drawn by hand and based on engineer?s experience. However, having automatic procedures for forming the shapes can increase the quality and decrease the efforts required. These shapes need to be homogenous in grades and rock types so that the quality and dilution of material sent to the plant can be estimated with the good approximation. In this paper, a clustering algorithm with shape control is introduced which can provide reasonable guidelines for all the aforementioned shapes by manipulating its parameters. At the end, implementations of the algorithm on a small part of a gold deposit with different mining strategies is presented and evaluated based on homogeneity of grade, rock types and determined destinations as well as the shape.

Feb 27, 2013

By Michael J. Miller

In the design of a modem mill, a stockpile storage system for raw and/or semi-processed ore has become almost indispensable. This paper discusses the benefits of such stockpile storage as well as the various types of belt conveyor stockpiling units available. Particular attention is given to large radial stackers since they offer the greatest flexibility. Stacker control systems and accessory equipment are briefly discussed. Various alternative reclaiming arrangements for stockpiles are reviewed and a discussion of the advantages and drawbacks of each arrangement is included.

Jan 1, 1979

By K. Burke, K. L. Myers, R. Espell

Barrick Goldstrike’s (Goldstrike) AA Heap Leach Pad is an HDPE lined facility used for gold recovery from low grade ores using conventional cyanide heap leach technology, operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA Leach Pad Facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada’s closure requirements. Traditional Nevada leach pad closure has involved rinsing to reduce cyanide concentration to an acceptable level, followed by reclamation. However, certain metals and compounds are not typically reduced by rinsing and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as Nevada, the fine-grained layer will rarely reach full saturation and the cover will be able to store water during precipitation and allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22 m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the re-contoured AA Heap Leach Pad was specifically designed to enhance the revegetation, reclamation, and sediment yield control aspects of the AA Heap Leach Pad closure, while resulting in a natural looking surface, compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for re-contouring and erosion control design.

Jan 1, 2001

By L. Lipsett

"Human rights can contribute to sustainability in the mining sector, both in theory and in practice. Both human rights and sustainability share a common concern to improve economic prosperity, environmental health and social equity by avoiding negative impacts and conflict, as well as by engaging with and empowering affected communities. Globally, there is an emerging consensus that companies have a responsibility to respect international human rights standards. Respecting human rights means that mining companies are responsible to ""do no harm"" to the people and communities affected by their operations. After a discussion of the Protect, Respect and Remedy framework for business and human rights, this paper illustrates some examples of how international standards for human rights and sustainability interacted in a recent assessment of Goldcorp's Marlin Mine in the Western Highlands of Guatemala. The final section explores how human rights should be integrated into broader policies and procedures for corporate sustainability. This includes integrating human rights into ESIA processes, legal compliance, corporate governance and grievance mechanisms. Pressures on mining companies to respect human rights will not disappear; therefore, a proactive and integrated approach to human rights is a fundamental component of a broader strategy for sustainability"

Jan 1, 2011

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By John Mitchell, Mark K. Jorgensen

Newmont Mining’s Ahafo Mine is located in Ghana approximately 300 km (190 miles) northwest of the capital city of Accra in the Brong-Ahafo region. The nearest city is Sunyani, located 45 km (28 miles) to the north. The Ahafo Mine will process ore from seven major pits that extend along a 40-km (25-mile) strike. Four pits are in the south and three pits are in the north. The resource is currently stated at 373 t (12 million oz). But it still has the potential for growth both from new discoveries and the development of underground operations.

Jan 1, 2007

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

Following a disaster in a mine, it is important to understand the state of the mine damage immediately with limited information. Computational fluid dynamics can be used to simulate and ascertain information about the state of ventilation controls inside a mine. This paper describes a simulation of tracer gas distribution in an experimental mine with the ventilation controls in various states. Tracer gas measurements were taken in the lab experimental apparatus, and used to validate the numerical model. The distribution of the tracer gas, together with the ventilation status, was analyzed to understand how the damage to the ventilation system related to the distribution of tracer gases. This study will be used in future research in real mine measurements to compare collected and simulated profiles and determine whether damage to the ventilation system has been incurred during an emergency situation, the nature of the damage and the general location of the damage.

Jan 1, 2011

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By M. J. Gula, S. S. Xue, E. P. Horwitz, J. T. Harvey

A study has been conducted to control iron in copper electrolyte streams using Eichrom Industries’s new Monophosphonic /sulphonic acid resin. The resin strongly and selectively extracts ferric ion over copper and cobalt from highly acidic copper electrolytes. The resin has a loading capacity of 27 g/L of iron and can be readily regenerated. In addition, the new resin can be easily synthesized using commercially available starting materials. This paper presents the experimental results for iron control in copper electrolyte streams using the new resin and discusses its potential applications to other hydro-metallurgical streams.

Jan 1, 2000

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By R. J. F. Goodfellow

Many underground projects now include preparation of a Risk Register through planning and design as a tool for project and risk management. There is still significant discussion within the industry as to whether and how to best present the Risk Register through the bidding process and the construction phase of a project. While the ITIG Code of Practice for Risk Management of Tunnel Works recommends this approach of continuity in risk management procedures, it is silent on the specifics of how this should be achieved. This paper will explore the perceived benefits and disbenefit of including the project Risk Register with bid documents; format and content that should be transferred and lessons learned using the case history of bidding and early construction phase of the Bi-County Water Tunnel in Montgomery County, MD