Search Documents

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

By Tim O’Neil

If you build a big truck, build a big tire to match it. Let that haulage synergy aid the economics, productivity and lessened maintenance for the unit. Now, Cater-pillar and Michelin have done just that. Discussions began in 1996. Caterpillar was making plans for its 797 ultra-class haul truck. The development team realized the need for a tire that could withstand extreme loads. The 797 would weigh 558 t (615 st) and be capable of 64 km/h (40 mph) speeds. So Caterpillar approached Michelin. The two companies realized the benefits of jointly developing a tire for the 797.

Jan 1, 2002

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By M. Rufli

Until not so long ago most ring geared mills were operated with fix speed motors only. By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The sophisticated operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore utmost availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives. Now this paper is focusing on the experiences gained with this kind of sophisticated ring geared mill drive system rather than only show and explains the operational benefit of the different functions. Several measurements of different operating conditions, starting, frozen charge remover, controlled roll back, backlash, etc., made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. The accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.

Jan 1, 2011

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By K. K. Bhattacharyya

Vast deposits of lignite occur in the Gulf Coast states and northern plain states. Lignite resources are cited to be over 43 billion tons in the Gulf Coast states. An additional resource of 16 billion tons are reported in North Dakota (Jackson, Smith, 1981). All lignite in the U.S. is mined at present by the open pit method. Draglines and scrapers are primarily used to remove the overburden. Bucket-wheel excavators are also being considered for new mines in the planning stages. Lignite seams are mined using front-end loaders, shovels and trucks, or Easi-miners. The depositional environment of lignite is weak sedimentary soils and rock. Ground water is often encountered within the mining depth. Surface water resulting from heavy rainfall or snow melt contributes to the problems of mining. Mining depths of up to 60 m (200 ft) are under consideration. Draglines exert additional loads on the highwalls and spoil piles. The combination of any number of these factors may cause instability of the slopes. Bearing pressure, trafficability, and settlement can also be a problem for excavation and loading equipment.

Jan 1, 1982

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by distributions of particle composition, size or shape). For such analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) may represent a powerful tool. This article is a preliminary investigation of SEM-EDX to characterize respirable dust from an underground coal mine in Central Appalachia. Samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate respirable dust concentrations during sampling. This data was compared to particle densities observed under the SEM. Dust is generally defined as small, solid particles with an effective diameter between 1 and 100 µm. In underground coal mines, dust is produced by a variety of activities such as coal and rock cutting, materials handling, haulage and from a variety of materials. While the coal itself is primarily made up of organic carbon, it is estimated that as much as 60 percent of coal mine dust consists of mineral matter, including clays, metal oxides and sulfides, carbonates, quartz, phosphates and heavy minerals (WHO, 1997). Mineral matter may be ingrained in the coal seam or associated with adjacent or interlying strata, and may also be contributed by specific activities such as rock dusting. When dust is generated or made airborne, suspended particles tend to settle slowly with gravitational forces, but can remain airborne for extended periods of time depending on environmental conditions such as air velocity (Courtney et al., 1986) and particle properties such as size (ISO, 1995; WHO, 1999). Thus, miners working underground are routinely subject to occupational dust exposures ? with highly variable characteristics between and even within mines.

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986