Search Documents

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and1580ºC under 0.03 atm, 0.05 atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged toSiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S) systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations, the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80 and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC, respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermo-dynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on a pseudo ternary SiO2? (AI2O3+CaO+MgO) ?(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: chromium, slag, equilibrium

Jan 1, 2004

By E. V. Lilford

Equity investors and project sponsors have divergent views about expected or minimum returns that should be generated by a mineral project. Irrespective of their views, the fundamental estimation of the corporate cost of capital remains singularly determinable, with additive components of risk and uncertainty often incorporated in the final analysis. This paper discusses and details the fundamental, numerical determination of the corporate cost of capital.

Jan 1, 2006

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005

By D. Vogt, T. Hattingh

"This paper argues that the technology change to mechanization is also going to require a change in people. It presents a model for technological progress and adapts it to the mining industry. It then goes on to motivate the need for mines to become learning organizations in order to achieve maximum value from their people as they become less labour-intensive. In an important sense, mechanization is as much about knowledge as it is about technology.The change when a mine introduces mechanization or a level of automation is not simply one of technology but also a stage in the development of mining from ‘art’ to ‘science’. ‘Art’ describes a state of technology characterized by tacit knowledge, an understanding that comes only from experience, and has no formal procedures and little structure. In contrast, ‘science’ represents a state of technology where all the component processes are understood in detail, all knowledge is explicit, and processes and structures are formal.Studies of other industries, including metal part manufacture and aviation, show that each stage in the progression from art to science changes the nature of the organization and requires a different mix of skills from the workforce. Perhaps the most important change is the increase in knowledge and decision-making required as the technology gets closer to science.There is anecdotal evidence that South African underground hard-rock mines are not learning organizations. Mines by their nature are capitalintensive with long lead times from investment to returns, so there is reluctance to change from the original plans or to encourage staff to think independently. Particularly as mines move from art to science, this reluctance must be overcome.The important lesson for engineers involved in introducing mechanization is to understand that success or failure will be determined by the people involved, and not solely by the technology. The process will almost certainly require a culture change on the mine. We recommend that the mechanization team includes an expert in human and organizational behaviour to ensure that a receptive workforce and management are in place to accept the new technology when it arrives."

Jan 1, 2016

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

Changes in reductant and energy inputs which are required to adjust the slag composition in anilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input does also hold for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

By R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key aspect of mechanization is the optimization of equipment utilization, and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2007

By M. Rakoma

Following the blasting fatality on 17 December 2009, Landau Colliery was forced to change from the blasting practices that had been utilized since the start-up of the mine. Since then, attempts have been made to optimize blasting results. The challenge is rooted to the mining environment - during the early life of the mine, mining took place in virgin areas, whereas currently mining is taking place in areas overlying old underground bord and pillar workings. The underground bord and pillar workings aggravate phenomena such as spontaneous combustion, hot holes, and sinkholes. The 2009 fatality was attributed to hot holes causing premature detonation. Landau has been struggling with poor results from their overburden and coal blasts; leading to poor fragmentation of overburden and the PI parting that lies between the No.1 and No.2 coal seams. An extensive literature survey was completed in order to identify possible alternative solutions that could be evaluated for this unique mining environment, which demands a high degree of caution during mining to ensure factors such as dragline stability and personnel safety. The literature survey confirmed that the previous blasting technique, which was mainly characterized by air decking, was indeed the more efficient, although it was deemed unsafe because of the possibility of hot holes and the high sensitivity of detonators. Potential modifications to the blasting technique were modelled in a Microsoft Excel simulation that was available from the mine, and pit visits were conducted in order to determine whether implementation would be a problem. From the model it is evident that results can be improved by changing the current burden and spacing ratio. Visiting the pit revealed that the tie-in pattern and drilling inaccuracies are contributing to problem areas.

Jan 1, 2013

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By C. Lumley

The management of the Anglo Platinum (AP) mining technical systems (MTS) embarked upon a process of defining the strategy for the MTS department. The newly established department forms part of the greater Group Information Technology (IT). The strategic process took place within an environment that had witnessed a dramatic proliferation of IT implementations across the group within the last three years. The IT department has been structured in terms of the classical plan, build and run functions with the applications and integration streams running perpendicular across these three functions. The application stream is divided into commercial and mining technical systems with business systems integration the third stream. The mining technical systems department supports mine management to effectively gather, analyse and disseminate data relating to the ore reserve by integrating a number of strategically selected IT applications to ensure that the safety, legal and operational requirements are met. This service to business is rendered by management of a strategic outsource partner via tightly controlled service level agreements (SLAs). The framework used for creating a mining technical systems department that is empowered to add value to business was formulated using the AP value chain as both the starting point and guiding process to ensure alignment to the greater internal strategy of the business. Keywords: Platinum, Mine planning, Mining technical systems, Value chain.

Jan 1, 2003

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2 slags that are typically encountered in the production of manganese-containing stainless steels. A gas equilibration-quenching technique was employed in measuring the activities. Activities of Mn in Pt-Mn alloys were redetermined at 1600ºC, which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600ºC. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient regression models were developed to predict the activities and activity coefficients of MnO in slags at 1600ºC. Keywords: activity, MnO, slag

Jan 1, 2005

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

By I. M. Wolf, S. A. Usmar, L. A. Cornish

The limiting criterion in the use of stainless steel for certain forming operations such as coining is its hardness, which determines parameters such as required striking pressure, wear on dies, and integrity of pattern detail. Attention is given here to the development of ultra-soft ferritic stainless steels for coinage. In the first instance, the influence of carbon content on the striking properties of a series of commercial and experimental 17%Cr alloys was evaluated. It was found that a lower carbon content permitted the striking of relatively highly profiled and intricate patterns, provided that the hardness did not exceed 125 HV. Hardnesses as low as 115 HV were achieved in the fully annealed condition, but these alloys required high striking pressures. In a further study, three grades of experimental 14%Cr ferritic stainless steels were produced with a view to optimizing the ductility. When the residual impurities were minimized, hardness values of about 100 HV and lower were achieved. Micro-alloying additions allowed the heat-treatment response and grain size to be controlled. Excellent tensile properties, with elongations of up to 42 per cent, were achieved in the fuly annealed condition, and highly profiled patterns were produced in coining trials.

Jan 1, 1993

By K. R. P. Petersen

Paper written on project work carried out in partial fulfilment of M.Sc. Eng.(Metallurgical Engineering) degree The interrelationship between mineral liberation and leaching behaviour of a gold ore is ill defined, mainly due to the complexity of both leaching and mineral liberation. This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organizing neural net, which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 8.1%). Moreover, the self-organizing maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2003

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014