Search Documents

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By J. M. Ortiz

Grade control and short-term planning are usually based on the samples obtained from blastholes. These samples may carry a large sampling and sample preparation error. At El Tesoro copper mine in northern Chile, an advance drilling grid is used for short-term planning and grade control. These drill holes are sampled well in advance, and a short-term model that incorporates several variables and sophisticated estimation methods can be prepared for decisionmaking. An additional advantage of the advance drilling samples is that reverse circulation can be used instead of conventional down-the-hole equipment, and a very careful sampling and sample preparation process can be implemented, reducing the total sampling error. Advance drilling can be performed on a wider grid than blasthole drilling, hence the decision about the grid requires assessing the economic benefit of different sampling grids. Furthermore, this process allows the cost of poor sampling and the effect of different estimation procedures to be quantified. We demonstrate the optimization of the drilling grid for short-term planning and grade control at El Tesoro mine by means of the economic evaluation of the performance of different drilling grids, with different drilling techniques (which differ in the sampling error). The methodology is based on creating dense (exhaustive) geostatistical simulations of the grade distribution over a volume defined for a production period in respect of the geological model, and assuming each simulation as the true grade distribution. Then, samples are obtained from the exhaustive simulations at a spacing similar to the advance grid to be evaluated, and a sampling error is added. The short-term estimation procedures used on the mine are applied to determine the destination of each block and the profit obtained. This profit can be compared with the maximum profit (unachievable) and with the profit under different sampling errors and grids. The results show that the current 8 x 8 m drilling grid is appropriate and by reducing the sampling error, misclassification is also reduced, leading to an increase in profit of about US$ 5 million in 4 years.

Jan 1, 2012

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By M. Gous

Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC arc furnace, titania slag, pig iron Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilisation and furnace stability, complemented by continuous improvement drives, will be the vehicle to drive performance in the short term, with longer-term performance enhancements due to strategic process development.

Jan 1, 2006

By S. M. Spottiswoode, Linzer. L. M.

We report on further progress in improving seismic locations by using the so-called double-difference method (Spottiswoode and Milev, 1998 and Waldhauser et al., 1999). Double-differences are obtained either using picked arrival times or various measures of time differences obtained from waveform pairs. The double-difference method provides for much improved relative locations by reducing the effect of the errors in the wave velocity of ray paths between each event and each geophone. Further improvements are obtained by using known locations, such as blasts. One of the difficult problems that we have overcome is that of finding the best “weights” for the time corrections. Experience obtained in relative moment tensor inversions by Andersen (2001) suggests that use of median corrections is both more stable and more accurate, even while the locations of the individual events is based on weighted least-squares minimization. A hybrid location program with known reference events has been developed. Tests on a synthetic data set gave relative locations that were much less widely spread than the absolute locations. The use of known event coordinates (blasts) moved the relative locations back towards the real locations. These results are confirmed in preliminary analysis of data from a mine. The absolute locations are adjusted using blast events restricted to the line of tunnel development. Inter-event distances are distributed in a power-law fashion that suggests that the relative location accuracies are improved by a factor of three or more. Nous rendons compte des progrès faits dans l’amélioration des locations de séismes en utilisant la méthode appelée de double- différence (Spottiswoode and Milev, 1998 et Waldhauser et al., 1999). On obtient les double-différences soit en utilisant des temps d’arrivée choisis soit des mesures variées de différences de temps obtenues de doublets de forme d’onde. La méthode de double-différence fournit des locations relatives très améliorées en réduisant l’effet des erreurs dans la vitesse d’onde des trajectoires de rayon entre chaque évènement et chaque géophone. D’autres améliorations sont obtenues en utilisant des locations connues, telles que les coups de mine. Un des problèmes difficiles que nous avons surmontés est celui de trouver les meilleurs coefficients de pondération pour les corrections de temps. L’expérience obtenue dans des inversions de phases tensorielles relatives par Andersen (2001) suggère que l’utilisation de corrections médianes est à la fois plus stable et plus exacte, même lorsque la location des évènements individuels est basée sur minimisation pondérée de moindres carrés. Nous avons développé un programme hybride de location avec des évènements connus pour référence. Des tests sur des données artificielles ont donné des locations relatives qui étaient beaucoup moins étendues que les locations absolues. L’utilisation de coordonnées d’évènements connus (coups de mine) a ramené les locations relatives vers les locations réelles. L’analyse préliminaire des données d’une mine a confirmé ces résultats. Les locations absolues sont ajustées en utilisant des évènements de coup de mine restreints à la ligne du développement du tunnel. Les distances entre chaque évènement sont distribuées comme par loi exponentielle ce qui suggère que les degrés d’exactitude des locations relatives sont améliorés par un facteur de trois ou plus. Wir berichten über einen weiteren Fortschritt, die seismische Positionen unter Verwendung der zu sogenannten Doppel-Unterschied-Methode (Spottiswoode und Milev, 1998 und Waldhauser et al.,1999) zu verbessern. Doppel-Unterschiede werden entweder mit ausgewählten Ankunftszeiten oder verschiedenen Messungen von Zeitunterschieden erreicht, die von den Wellenformpaaren erhalten werden. Die Doppel-Unterschied-Methode liefert viel verbesserte relative Positionen unter Verringerung der Auswirkung von Fehlern in der Wellengeschwindigkeit von Strahlengängen zwischen jedem Fall und jedem Geophon. Weitere Verbesserungen werden erreicht, indem man bekannte Positionen, wie Sprengungen verwendet. Eines der schwierigen Probleme, die wir überwunden haben, ist jenes des Findens der besten "Gewichte" für die Zeitkorrekturen. Die Erfahrung, die in den relativen Momentspannerumkehrungen von Andersen (2001) gewonnen werden bietet den Schluß an, daß der Gebrauch von mittleren Korrekturen beständiger und genauer ist, sogar wenn die Positionen der einzelnen Fälle auf der bewerteten Reduzierung der Methode der kleinsten Quadrate basiert. Ein hybrides Positionsprogramm mit bekannten Bezugsfällen ist entwickelt worden. Tests auf einem synthetischen Dataset gaben relative Positionen, die viel weniger weit gestreut waren als die absoluten Positionen. Der Gebrauch von bekannten Fallkoordinaten (Sprengungen) schob die

Jan 1, 2003

By A. E. Lewis

Particle morphology is a term that is used to describe the overall external shape and appearance of particulate solids. From the physical point of view, a precipitated solid is characterized primarily by the size and morphology of the particles (Sohnel andGarside, 1992). If the morphology of the crystal structures is to be related to the processing conditions, then the morphologies need to be quantified in some way. This can be achieved by using surface area measurements as well as fractal dimensions. The key idea is that rugged and indeterminate systems can be described by using a fractional number that describes the ruggedness of the system (Kaye, 1989). In other words, when the complexity of a structure, such as an agglomerate, increases with increasing magnification, it is useful to employ fractal dimensions to describe the structure. Fractal geometry proposes that, instead of attempting to measure the length of an irregular boundary, the rate at which the length of the boundary approaches infinity with increasing resolution should be calculated. Cross-sectional profiles of rugged particles can thus be quantified using the fractal dimension, and a measurement of the ruggedness of the morphology obtained. One of the additional uses of measuring the fractal dimension is that the measured value can be related to the physical properties and formation characteristics of the particle (Kaye and Trottier,1995). The morphology of nickel crystals was quantified with fractal dimension calculations of particle cross-sections. Particle cross-sections were obtained by mounting the particles in resin and polishing back. These were then photographed using Scanning Electron Microscopy and the resulting profiles analysed using the structured walk technique.

Jan 1, 2001

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By P. W. Lotz

Traditionally, bottle roll tests have been used to optimize the extraction process for best gold extraction and recovery. Such tests typically involve exposing the ore to defined reagent concentrations (lime, cyanide and sufficient oxygen) and balance the gold input with recoveries and losses. With mounting pressures to accommodate sustainability issues during development work, it became apparent that much more information would be required on the interactions and kinetic behaviour of solid and solution species during the entire leach process. This information is vital to enable proactive management of critical issues such as cyanide, arsenic, water and tailings management. Inadequate management of these aspects has led to temporary closures and, in cases of non-compliance, to the dynamically changing regulations. MINTEK?s advanced leach facility (ALF) is being developed with the aim of bridging the knowledge gap between the gold leach process and the predictable environmental impacts upon discharge. The facility aims to monitor all parameters of relevance such as pH, Eh, dissolved oxygen, metals, cyanide species, and viscosity during the entire process to enable more informed decisions on practical interventions. The presented set of data reflects first experiences gained from processing a refractory gold ore concentrate. Attempts at optimizing the process were limited due to the developmental nature of the work. Data relating to leaches with differing preoxidation conditions and cyanide staging is presented.

Jan 1, 2009

By A. R. Barnes, A. F. Newall

Keywords: Pyrometallurgy, furnace, smelting, spinel, PGM, phase diagrams As Merensky reef ores are replaced by UG2 ores, chromium levels in PGM smelting furnace feeds have steadily increased. Increased chromium levels lead to operating problems. Attempts to increase the chromium solubility in the slag by a variety of techniques create other difficulties. The authors have developed a technique for removal of the chromium spinel interface along with the matte for subsequent separation outside the smelting furnace by utilising differential solidification in the ladle. The process has been patented internationally with support from the Innovation Fund.

Jan 1, 2006

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

Current mine production planning, scheduling, and allocation of resources are based on mathematical programming models. In practice, the optimized solution cannot be attained without examining all possible combinations and permutations of the extraction sequence. Operations research methods have limited applications in large-scale surface mining operations because the number of variables becomes too large. The primary objective of this study is to develop and implement a hybrid simulation framework for the open pit scheduling problem. The paper investigates the dynamics of open pit geometry and the subsequent material movement as a continuous system described by time-dependent differential equations. The continuous open pit simulator (COPS) implemented in MATLAB, based on modified elliptical frustum is used to model the evolution of open pit geometry in time and space. Discrete open pit simulator (DOPS) mimics the periodic expansion of the open pit layouts. Function approximation of the discrete simulated push-backs provides the means to convert the set of partial differential equations (PDEs), capturing the dynamics of open pit layouts, to a system of ordinary differential equations (ODEs). Numerical integration with the Runge-Kutta scheme yields the trajectory of the pit geometry over time with the respective volume of materials and the net present value (NPV) of the mining operation. A case study of an iron ore mine with 114 000 blocks was carried out to verify and validate the model. The optimized pit limit was designed using Lerchs-Grossman?s algorithm. The best-case annual schedule, generated by the shells node in Whittle Four-X yielded an NPV of $449 million over a 21-year mine life at a discount rate of 10% per annum. DOPS best scenario out of 2 500 simulation iterations resulted in an NPV of $443 million and COPS yielded an NPV of $440 million over the same time span. The hybrid simulation model is the basis for future research using reinforcement learning based on goal-directed intelligent agents.

Jan 1, 2008

"Exploitation of an ore deposit can be optimized by adapting the beneficiation processes to the properties of individual ore blocks. This can involve switching in and out certain treatment steps, or setting their controlling parameters. Optimizing this set of decisions requires the full conditional distribution of all relevant physical parameters and chemical attributes of the feed, including concentration of value elements and abundance of penalty elements. As a first step towards adaptive processing, the mapping of adaptive decisions is explored based on the composition, in value and penalty elements, of the selective mining units.Conditional distributions at block support are derived from cokriging and geostatistical simulation of log-ratios. A one-to-one log-ratio transformation is applied to the data, followed by modelling via classical multivariate geostatistical tools, and subsequent back-transforming of predictions and simulations. Back-transformed point-support simulations can then be averaged to obtain block averages that are fed into the process chain model.The approach is illustrated with a ‘toy’ example where a fourcomponent system (a value element, two penalty elements, and some liberable material) is beneficiated through a chain of technical processes. The results show that a gain function based on full distributions outperforms the more traditional approach of using unbiased estimates."

Jan 1, 2015

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By C. Musingwini, G. Njowa, M. Burnett, C. C. Birch

From 2022 to 2040, the global demand for mineral commodities is projected to increase by fourfold to six-fold, largely due to traditional drivers such as population growth and urbanisation compounded by the adoption of decarbonisation technologies that are more mineral intensive than fossil fuel technologies. To meet this projected demand, companies operating in the minerals industry should accelerate the development of mineral projects. Since most of the companies generally operate in multiple geographical, regulatory or legislative jurisdictions, it is critical that the information on Mineral Resources and Mineral Reserves they report on in the public domain should be comparable and consistent across different jurisdictions. The Committee for Mineral Reserves International Reporting Standards fosters alignment of national and regional mineral reporting codes through an internationally accepted template that creates common technical understanding of definitions, classification, estimation processes and the Public Reporting of Exploration Results, Mineral Resources, and Mineral Reserves. The Committee for Mineral Reserves International Reporting Standards Template-based codes guide reporting at respective national and regional levels. Since mine planning is critical in the conversion of mineral resources to mineral reserves, a shared technical understanding should aid comparability of mine planning results. However, differences persist in the way mine planning results are reported. Unlike most previous studies, which have primarily focused on comparing mineral reporting codes, this paper updates and extends such comparisons by exploring how similarities or differences in reporting should influence the mine planning process. It also recommends some principle and process changes to assist mine planning professionals to improve consistency and comparability in reporting mine planning results.

Mar 30, 2026

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007