Search Documents

Proceedings of the Symposium on Face-end Technology. London, Institution of Mining Engineers, 1981. £25 per copy (members), £ 30 per copy (non-members) including postage. Reviewer: B.C. Alberts This book includes the papers presented at the Symposium, which was held in Harrogate, England, in December 1980.

Jan 1, 1982

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous 'merry-go-round' operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By E. J. Magri, D. M. Hawkins

This paper deals with an experimental programme carried out with a gold analyser in the period June to September 1979 at Loraine Gold Mines. The results were found to be reproducible, with no overall or conditional bias when the measurements were compared with those obtained from chip samples. The standard error of estimation of a 3 m reef exposure, which was the sampling interval, can be reduced by a factor of 2,5 if the complete stretch is scanned, rather than the taking of one chip sample in its centre. Complete statistical and computational procedures were developed for the fitting of the normal-Iognormal model to observed analyser data and for the determination of the most likely gold grade for a particular analyser measurement. (This corection procedure is necessary since a significant number of negative analyser measurements can be observed.) Panel averages of uncorrected scans showed a small conditional bias relative to those of corrected scans. However, uncorrected panel averages can be used for on-the-spot decisions regarding whole panels. For standard calculations of ore reserves, use should be made of corrected scans. Under reasonable assumptions, the use of the detector in the selective mining of low-grade narrow reefs such as the Basal Reef at Loraine Gold Mines, when compared with the conventional chip-sampling method, can result in a saving of as high as R40 million in present-money terms over the life of a project. The difference could be even larger in a highly variable reef like the B Reef at Loraine Gold Mines.

Jan 1, 1987

Brigadier R. S. G. Stokes of Sherborne, Dorset, is the oldest surviving member of the South African Institute of Mining and Metallurgy. He joined in 1904 and has been a member for 77 years. Book review Sittig, M. Hand book of catalyst manufacture. Park Ridge (U.S.A.), Noyes Data Corporation, 1978. The detailed information in this book is based on patents issued in the U.S.A. that deal with catalysts and their commercial technology. Project management The South African Institute of Mining and Metallurgy is to hold a Colloquium on Project Management in the Metallurgical Industry in March 1980. Ingenieurs-in-opleiding in die weermag Op 'n onlangse vergadering van die Suid-Afrikaanse Raad vir Professionele Ingenieurs is daar besluit om kwytskelding van jaargeld aan geregistreerde ingenieursin- opleiding wat tans met hulle tweejaar nasionale diensplig besig is, te verleen met dien verstande dat.... Engineers-in-training in the army At a recent meeting of the South African Council for Professional Engineers it was resolved that a remission of annual fees would be granted to registered engineers in- training who are doing compulsory two-year national service, provided that.... Processing of fine particles The Society of Mining Engineers of AIME is organizing an International Symposium on Fine Particles Processing, which is to be held in Las Vegas from 24th to 28th February, 1980. Economics of precious metals International Precious Metals Institute announces a Special Course for all interested in economic aspects of today's precious metals.

Jan 1, 1979

Book reviews Jones, M. J. (editor). Process engineering of pyrometallurgy. Proceedings of a joint meeting of the Institution of Mining and Metallurgy and the Institution of Chemical Engineers. London, Institution of Mining and Metallurgy, 1974. 105 pp. £6,50. Nim reports Report No. 1656 The analysis of geological samples for trace elements by direct-reading emission spectrometry. Report No. 1669 An assessment of the carbon-rod atomizer for the determination of silver.

Jan 12, 1974

By J. -M. Milazzo, T. Wallmach, S. B. Blancher, A. Amalric

In a FeNi electric arc furnace, the physical properties of the slag (chemistry, viscosity, liquid/solid/gas ratio) are of crucial importance in controlling the efficiency of the process. In this paper, we studied the slag crystallised on the walls of a semi-industrial furnace (freeze-lining), the slag rising through the burden during foaming phenomena, and the casted slag. The freeze-lining is the layer of oxides that crystallises on the refractory wall of a furnace, protecting it from chemical and mechanical aggression. It records changes in furnace conditions (slag chemistry, temperature, oxygen fugacity), which makes it possible to observe the impact of these elements. In the high reduction test, the freezing lining is composed of magnesian olivine. Switching to a low reduction process increases the Fe content of the olivine and causes orthopyroxene to appear, making the freeze-lining mechanically and thermally weak. Thermal incidents in the furnace cause significant slag foaming. This foaming is produced by a massive crystallisation of the olivine (due to the drop in temperature), and inducing an exponential increase in viscosity, preventing the free circulation of gases. These foaming episodes are also recorded in the freeze lining and form layers rich in gas bubbles, and therefore mechanically fragile. The slag casted and cooled in a ladle allows the first steps of slag crystallisation to be studied. Olivine is the liquidus phase, with a magnesium-rich core and an iron-enriched rim, contemporaneous with the orthopyroxene phase. The habitus of these phases is very similar to that found in komatiites for the same minerals. FeNi slag is therefore an industrial analogue that is easy to study and compare to komatiites. Keywords: Pyrometallurgy, ferronickel, slag, freeze-lining, characterisation, olivine, mineralogy

Jan 1, 2020

By D. Francois-Bongarcon

The ?Poisson effect? is defined and characterized. It takes place even when the material to sample is not liberated. Gy, Pitard, Ingamells, and others, including the author, recommend that a minimum average number of particles of mineral of interest characterize the recommended sample size. How many? Recommended numbers range from 6 to 40 particles depending on authors, corresponding to standard deviations of 41% to 16%. Some guidelines are proposed, and the often alleged ?double-Poisson? effect is examined.

Jan 1, 2009

By H. J. S. Kriek

Methods are described by which increased production is achieved whilst retaining full availability of equipment and decreased refractory cost. Refractory materials have certain limitations, and when these limitations are known the variables in operating practice having the greatest impact on refractory life can be controlled. The most important factors to be closely controlled are porosity, chemical constitution of refractory materials, slag basicity, slag volume, FeO content of slag and temperature at which the process is operated. Knowledge of the process is invaluable in deciding on the type of refractory to be used. The types of refractories used in and the operating variables of the ironmaking, steel making and steel finishing units are described.

ORANGE FREE STATE BRANCH Proceedings of the Annual General Meeting The Annual General Meeting of the Branch was held in the St. Helena Club on Tuesday, 3rd October, 1972 at 8.00 p.m. Mr J. M. Meyer was in the chair. METALLURGISTS AND COMPUTERS An address delivered at the Annual General Meeting of the O.F.S. Branch by Prof D. D. Howat. Most men who remain in mining and metallurgy like their jobs. There are many times when you say to yourself or to your wife - 'Anybody can have my job - if they want it'. You feel so fed up and frustrated everything that could go wrong has gone wrong.

By T. B. Beeton

In view of the limited reserves of good-quality coking coals in South Africa, Iscor has been involved in direct reduction since the middle sixties. Since the early seventies, its interest in direct reduction was stimulated further by a swing towards' continuous casting, which, in turn, contributed to a shortage of the scrap supply for electric-arc-furnace (EAP) steelmaking. Rock engineering The First International Conference-Rock Enginet:ring and Excavation in an Urban Environmentorganized by The Institution of Mining and Metallurgy and the Hong Kong Section of the Institution, in association with the Hong Kong Institution of Engineers, will be held in Hong Kong from 23rd to 28th February, 1986. SPOTLIGHT on Gold Fields National Engineering Awards For the Gold Fields Foundation National Engineering Awards, each university affiliated to the South African Federation of University Engineering Students (S.A.F.U.E.S.) selected a candidate who, in their opinion, presented the most outstanding design project in their final year during 1984.

Jan 1, 1985

In the investigation described here, it was found that the main effect of temperature is on the rate of flotation, and that adsorption of the reagent is not rate controlling. Above 10°C, the flotation rate of pyrite and gangue increases almost exponentially with a rise in temperature. Below that temperature, the flotation rate of pyrite shows a sudden marked decrease, that of gangue increases, and the sulphur grades are significantly poorer. In the flotation of pyrite, the mass transfer of the pyrite from the pulp to the troth is thought to be the ratecontrolling step, whereas the flotation of gangue is controlled by the combined effect of the stability and velocity of the froth and the viscosity of the elutriating medium. The latter is probably the controlling effect at temperatures below 10°C. Little difference was noted in the recoveries (provided no time limit was set) with changes in temperature; hence adequate recoveries can be obtained at Iow temperatures by the introduction of longer residence times for the pulp. The adverse effects of Iow temperatures on grades can be overcome only by additional cleaning or by heating of the pulp.

Jan 1, 1984

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986

By R. R. Maclachlan

The Estimation of Fragmentation in Blast Muckpiles by Means of Standard Photographs, by H. van Aswegen and C.V.B. Cunningham. Journal of the South African Institute of Mining and Metallurgy, vol.86,no. 12. pp. 469-474. Dec.1986.We have recently read the above paper and wish to make a number of observations.

Jan 1, 1988

By G. F. Balderson

In response to the written contribution made by G. J. C. Young to the above paper, I would like to make the following points. Paragraph 1 The build-up of oxidized coatings on cone surfaces has not been a problem in other applications similar to that at President Steyn. The following companies have commented.

Jan 1, 1982

By F. K. Mulenga, M. Lusambo

"Geometallurgical models are a strategic tool used primarily in planning, diagnosis, and process optimisation. This paper discusses the development of a predictive model for flotation recovery at Kansanshi concentrator in Zambia as a function of key operational parameters. Daily data for milling and flotation from the circuit processing the copper sulphide ore was analysed. This data, recorded over a period of one year of production, was collected from diverse sensors measuring semi-autogenous milling and flotation parameters. Statistical analysis showed that copper head grade, acid-insoluble, and acid-soluble copper, SAG mill throughput, ball mill load, and tonnage of feed material to the SAG mill in the -125 +63 mm size fraction contributed to the prediction power of the proposed empirical model by as much as 90%. Finally, a proposal was made for the development of a simulation model under MODSIM®, a flexible tool for mineral processing applications. This was to test the limitations of the empirical model for future refinement. IntroductionKansanshi is the largest copper mine in Africa and the world’s eighth largest copper producer, with a total of 253 272 t of copper produced in 2016 (Newall, 2017). It is located approximately 10 km north of Solwezi, the capital and administrative headquarters of the North Western Province, Republic of Zambia. The ore deposit consists predominantly of chalcopyrite and malachite with variable amounts of chalcocite, bornite, chrysocolla, and azurite. Because of the varying proportions of sulphide and oxide copper minerals, the ore is classified into three distinct categories: sulphide, mixed, and oxide ores. As such, three separate processing circuits are used to mill the ore down to a standard targeted grind size of 80% passing 150 µm before froth flotation and leaching.A lot of research and development has been done to improve the performance of the sulphide ore circuit at Kansanshi. Despite the research efforts and subsequent operation, the sulphide ore circuit did not attain the target recovery and grade for 2016, primarily because of the complexity of the orebody.The constant drive to achieve the set production target of recovery and concentration grade after froth flotation motivated the development of a tool for the prediction of recovery. The anticipated benefit is not only to enable the plant to apply corrective actions when needed, but also to make a tool available for the quick assessment of the plant performance of the. For that purpose, data spanning June 2016 to May 2017 was analysed, cleaned up and curvefitted to an empirical model. In doing so, key parameters were determined and calibrated to represent the behaviour of the plant."

Nov 1, 2018

By T. Bednarski, L. Thomas, G. Banza, D. Muteba, P. Cole, M. Soderstrom

"In copper solvent extraction, aqueous-in-organic entrainment results in the carry-over of unwanted species into the electrowinning process with negative cost implications. The need to bleed is increased and the purity of the copper cathode is potentially compromised, depending on the impurities being transferred (Cl, NO3, Fe, Mn). In some cases, entrainment results in elevated levels of manganese in the electrolyte which can cause oxidative conditions to develop and degradation of the organic phase. Degraded organic phase detrimentally affects the physical performance of the copper solvent extraction process, contributing to even higher aqueous-in-organic entrainment. Aqueous entrainment may be minimized through good operating practices and maintenance of the organic quality, but the accurate measurement of entrainment remains a challenge. This paper presents coalescing devices designed to provide more exact measurements of aqueous-in-organic entrainment. IntroductionMany copper solvent extraction (SX) plants experience high aqueous-in-organic (A-in-O) entrainments but are unaware of the extent of the problem because entrainment is often not measured. Aqueous entrainment results in the carry-over of unwanted species into the electrowinning (EW) process and the need to bleed to maintain acceptable concentrations in the electrolyte. The costs associated with the bleed are exacerbated in copper plants where aqueous entrainment levels are high. Other than these direct costs, there are operational consequences of the build-up of certain species in the EW circuit that can have deleterious effects on plant performance.Minimizing aqueous entrainment in operating plants requires an understanding of the factors that affect entrainment levels. Both chemical and operational influences are discussed in this paper. The difficulty of obtaining a representative sample makes it challenging to obtain an accurate measure of aqueous entrainment from a continuous process like SX. Coalescing devices used to get a more precise measurement of A-in-O entrainment are useful to complete mass balances around the SX circuits. Alternatively, mass balances can be used to estimate aqueous entrainments and are helpful as a tool to troubleshoot operations with a view to improving plant performance."

Jan 1, 2016

A. Sutherland Brown (ed.). Porphyry deposits of the Canadian Cordillera. The Canadian Institute of Mining and Metallurgy, Special Volume 17, 1976. C. G. Down and J. Stocks. Environmental impact of mining. G. B. Rothenberg. Refractory minerals. Park Ridge (V.S.A.), Noyes Data Corporation, 1976. Geology, mining and extractive processing of uranium. London, Institution of Mining and Metallurgy, 1977.

Jan 1, 1978

By G. T. G. Emere

With the assistance and encouragement of Mr B.C. Alberts, the Institute's immediate Past President and Iscor's Senior General Manager: Mining, the Committee of the Johannesburg Branch recently organized a two day excursion for members to the northern Transvaal. The itinerary included visits to the Grootegeluk colliery, the Matimba power-generation utility, and the Thabazimbi iron-ore mine.

Jan 1, 1989

The 92nd Annual General Meeting of The South African Institute of Mining and Metallurgy was held on Wednesday, 16th August, 1989, at Kelvin House. Mr C.E. Fivaz (President) was in the Chair, and declared the meeting open at 16:05. Obituaries The President announced the deaths of the following members of the Institute:

Jan 1, 1989