Search Documents

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By A.M. Edwards

1. Book reviews Platinum in South Africa, compiled by A.M. Edwards and M.H. Silk. Randburg, Council for Mineral Technology (Private Bag X3015, Randburg, 2125 South Africa), 1987. 55 pp. U$30. Reviewer: R.D. Wintle Scientific and technological developments in extractive metalurgy-G.K. Wiliams Memorial Volume. Parkvile (Australia), The Australasian Institute of Mining and Metalurgy, 1986. $A12 (incl. surface postage). Reviewer: T.Y. OweD Ion exchange and sorption processes in hydrometa/urgy, edited by M. Streat and D. Naden. Chichester, John Wiley & Sons, 1987. 229 pp. Reviewer: B.R. Green Role of Government in mineral resources development, edited by Michael J. J ones. London, The Institution of Mining and Metalurgy, 1985. 180 pp. £40. Reviewer: K.E. Ducat 2. Recent publications Annual report 1987. International Tin Research Institute, Kingston Lane, Oxbridge, Middlesex UB8 3PJ, England, 1988.Tin and its uses no. 156. Address as above. 3. Mintek reports Application Report no. 5 The production of and alusite and other refractory minerals. 1988. 16 pp. . Application Report no. 6 The development up to commercial application of a process for the recovery of lead, copper, zinc, and silver from the Black Mountain deposit. 1988. 14 pp.

Jan 1, 1988

By V. E. Cogho

Optimum Coal Mine comprises numerous defunct, active, and future mining sections. The mine is primarily a large opencast coal mine; however, underground mining activities will be increasing steadily over the next five years. Opencast and underground mining activities have a significant impact on surface and groundwater resources. To ensure that the mine will be able to continue with its mining operations in the catchment, the extent of this impact requires that substantial intervention and mitigation measures need to be implemented to ensure the environmental integrity and economic use of the catchment's water resources. In developing a sustainable long-term mine water management strategy, numerous scenarios had to be analysed. The various scenarios are a combination of water and land management activities. The main components of the mine's integrated water management strategy include: ? Management of water recharge by continual and appropriate rehabilitation of disturbed land ? Beneficial re-use of impacted mine water for coal plant process water and mining operations ? Reclamation and desalination of remaining excess impacted mine water to potable standard. From the mine's long-term water balance, it is evident that the continued implementation of numerous water management actions is required to mitigate the water resources impact in a sustainable manner. In addition, the installation of a water reclamation plant at Optimum Coal Mine (15Ml/day) is a key step for the mine to achieve a zero impact target.

Jan 1, 2012

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005

Discussion of the previous paper E. N. H. MOLLOY The first 22-foot-diameter Aerofall mill was installed at Mangula in 1957. This was fitted with cast-iron trunnion'! located to the mill shell with 2-inch-diameter mild-steel bolts. O.F .S. Branch Minutes of the General Meeting held at the Welkom Club on Wednesday, 2nd June, 1976, at 4.00 p.m. Mr G. J. C. Young (Chairman of the O.F.S. Branch) was in the Chair. Also present were:

Jan 9, 1976

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By F. M. Russell

Scheduling the extraction and rates of production for an underground mining operation is a common task carried out during the life of a mine, from the initial feasibility study through to the final production phase. The scheduling process can be complex when several requirements have to be satisfied, for example, match mill capacity and maximize net present value while constrained by mining sequence and availability of resources. Many mines have computer programs relevant to their operation but because they are site-specific they need considerable reprogramming to be adapted to other operations. Other methods currently in use also suffer drawbacks: manual spreadsheets are laborious, computerized spreadsheets cannot handle sufficient constraints, and operations research techniques require a complex mathematical model to be set up. The use of network analysis techniques has been proposed previously but the unavailability, until recently, of easily used computer programs has not allowed this approach to be developed. There are now many programs which can be used; however, the particular program which has been adapted to mine scheduling is Metier's 'Artemis-PC' running on IBM-XT or compatible machine. The use of network analysis offers many advantages, including the use of a logical mining sequence; activities can be as detailed as required; related activities can be readily incorporated, and costs can be easily extracted. A heuristic approach is necessary to optimize the schedule, but the ease and speed of program execution enables this to be readily achieved, while leaving the mining engineer in full control. The paper discusses the problems encountered in mine scheduling and current solutions. It then details the use of network analysis techniques and the application of the Artemis-PC program to solve mine scheduling problems.

Jan 1, 1987

[The following notations will be used: O an ore body. W a sample of size w located in O; the size of this sample. W a block or a sample, of size W, located in O; the size of this block or sample. z' a point in W. W' a block or a sample, of size W' greater than or equal to W, located in O; the size of this block or sample. z" a point in W'. y (h) point semivariogram in O. s (h) point covariogram in O. In the previous chapter, we saw that the point semivariogram y (h) usually cannot be estimated directly from the data available. Rather, the values of samples of size w are available in O, and from these a regularized semivariogram y w (h) can be estimated. The following relationship has been proved (5.8): Y w(h) = Y (w;w+h) - Y (w;w). y (w;w+h) is the average value of y (z' z") when z' takes all possible positions in a sample w and z" all possible positions in a sample w+h of the same size, h being the distance between w and w+h. y (w;w) is the value of y (w;w+h) for h = 0, i.e. the average value of y (z' z") when z' and z" take all possible positions in w. We also saw that the regularized covariogram aw(h) is related to the point covariogram a (h) as follows (5.9): w(h) Gr In the following chapters, it will be shown that calculation of the average value y of y, or -a of a, in the general case relating to samples or blocks W and W' which need not be of the same size, plays a very important part in all the practical applications of geostatistical theory. The purpose of this chapter is to introduce various methods of calculating y and a-. Furthermore, mathematical equations and graphs are provided which can be used when the point semivariogram can be represented by one of the more common equations, and when the blocks W and W' are of simple shape. By definition (Fig. 6.1): [ ] Y (W;W) = WW f dz' f y (z' z") dz" (6.1) in W z" in W']

Jan 1, 1978

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By P. J. Bartlett, H. A. D. Kirsten

A two-dimensional numerical scheme for the simulation of the plastic stress-strain properties of rock, and the various components of rock reinforcement and shotcrete, was used to rigorously determine the characteristics of tunnel support under squeezing conditions. D-shaped tunnels varying in size from 2,8 to 6,5 m in height and width were considered. The four main mining stages in the BAS block cave on Premier Mine were simulated as alternative sets of field stresses. The rock reinforcement comprised 1,8 m long fully grouted rockbolts and 6,0 m long fully grouted cable anchors at various spacings, and of various tensile and bond strengths. Various thicknesses of shotcrete and footwall support configurations were also considered. It was found that shotcrete and rock reinforcement, owing to inherent differences in stiffness, do not function in unison. As monolithic application, shotcrete has an overriding avidity for the imposed loading and destructs itself unless of extraordinary thickness. Under squeezing conditions, it accordingly supports the excavation surface while the rock reinforcement contains on-going convergence. The loads in the various support components can be determined only by simulation of the shotcrete as a stress-relieved medium to represent its broken condition in the field. The loads in the rock reinforcement vary around a tunnel and are the largest in the sidewalls. The loads increase with an increase in tunnel dimensions, the increase in load in the sidewall due to an increase in height being larger than that in the hanging- and footwalls due to an increase in width. Depending on the strength of the rock, the loads in the rock reinforcement become prohibitively large beyond a certain size of tunnel. The reinforcement of footwall rock can be omitted without adversely affecting that in other walls, provided the tensile and bond strengths of the reinforcement are not limited. The resulting footwall heave may, however, result in undermining of the reinforcement in the adjoining walls. A relative depth of anchor of 1,37 provides adequate bond strength in the larger sizes of tunnel, whereas, in smaller tunnels, anchor length is determined by the allowable convergence. The lack of fun column grouting adversely affects the efficiency of rock reinforcement to a major extent. The loads in rock reinforcement are very sensitive to the strength of the rock. Owing to a lack in refinement and calculational rigour, empirical classification systems are an inappropriate means for the design of tunnel support in squeezing conditions and, as a result, grossly unclear-estimate the support requirements.

Jan 1, 1992

By D. Amariei, G. Bartolacci

Preconcentration of precious and base metal ore types is becoming more relevant with the discovery, the development and the operation of many lower grade deposits around the world. Ore preconcentration designates an operation consisting of sorting an ore to reduce the quantity of waste material sent to the concentrator. It can be seen as rejecting waste material as much as possible, without compromising the recovery, or as the recovery of as much valuable metal as possible into an optimum mass yield. Benefits of preconcentration are multiple: grinding energy savings, costs reduction, lower environmental footprint, extension of the reserves, etc. However, all of these benefits do not apply simultaneously and are not applicable to each ore type. Technologies employed for preconcentration are highly dependent on ore properties, especially on the particle size at which the gangue is liberated. Thus, from coarser to finer particle sizes, technologies such as screening, ore sorting, gravity separation (Dense Media Separation (DMS) and jigs) and coarse flotation could be used for the rejection of liberated gangue. The difficulty starts when a benchmark is needed to select a suitable technology, especially for low-grade gold deposits. This paper presents the challenges of comparing lab-scale technologies (DMS versus jig) for gold preconcentration. The experimental data will show to what extent comparing two lab-scale gravity technologies for gold preconcentration can be challenging. An attempt to evaluate the energy savings by assessing the hardness of the tailings after gravity separation will also be presented. Keywords: Challenges in gold preconcentration, gravity separation, jig, dense medium separation

Jan 1, 2020

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By Ernst-Ulrich Reuther, Alexander Donmen

Mine ventilation in the German coal mining industry is concerned mainly with problems of thermal environment arising from greater depths and with increasing emission of methane gas. The development of computer techniques over the past ten years for solving these and ancillary problems is reviewed. The emphasis from a planning and control point of view falls mainly on ventilation network calculations, temperature predictions and advance estimates of methane emission.

Jan 1, 2014

Introduction to high temperature oxidation of metals, by N. Birks and G. H. Meier, London, Edward Arnold, 1983. 19S pp. R30,25. Reviewers: M. B. Cortie and G. G. Garrett Seam gas drainage with particular reference to the working seam, edited by A. J. Hargraves. Woollongong, The Australasian Institute of Mining and Metallurgy. 370 pp. $A30. Reviewer: C. J. Fauconnier New books Solvent extraction Part I, by G. M. Ritcey and A. Ashbrook. Amsterdam, Elsevier, 1983. Elektronishche Steuerungen und Mikroprozessoren im Bergbau. Sicherheit und Zuverlassigkeit Environmental impact control. Philosophical and procedural guidelines for the planning professions Mineral processing and extractive metallurgy. Reagents in the minerals industry.

Jan 1, 1984

By A. V. Rasskazova

Theoretical substantiation of leaching of clustered ultra-fine gold by the electro-photo activated cyanide and chloride solutions is given in the paper; and processes of activation of leach solution by electrolysis and photo-activation are described. Comparative experiments on electro-photo activated leaching of ultra-fine gold from refractory ores by cyanide and chloride solutions were carried out. The material for research is primary ore of the Pogromnoe deposit (Russian Federation, Trans-Baikal Territory). The ore is characterised by the minimum sulfide minerals and the organic carbon content. Gold in ores of this deposit is presented as mainly ultra-fine. Gold inclusions in quartz and silica-alumina minerals (metasomatic minerals) are ultra-fine. Sulfide minerals (2.5-3%) are presented in ore generally by pyrrhotine (gold content does not exceed 10 g/t). Standard cyanide technology provides 49.5% gold recovery. Photo-electro activated air saturated NaCN provides 69.9% gold recovery. Laboratory research of chloride-hypochlorite column leaching demonstrated that the electro-photo activated method provided 78.9 % gold recovery to pregnant leach solution. Chloride-hypochlorite photo-electro activated solution can provide higher level of gold recovery with shorter process duration (10 days) in comparison with cyanide (40 days). The final decision regarding the choice of leach solution has to be done on the basis of technical and economic calculations. Keywords: Ultra-fine gold, cluster chemical reactions, active clusters, leaching, electro-photo activation of leach solution

Jan 1, 2020

Infacon 74 Members are reminded of the International Ferro-Alloys Congress that is to take place in Johannesburg between 22nd April and 1st May, 1974. The Congress is being held jointly by the National Institute for Metallurgy, the Ferro Alloy Producers' Association of South Africa, and the South African Institute of Mining and Metallurgy. Correspondence and enquiries should be addressed to The Secretary, Organizing Committee, INFACON 74, Private Bag 7, Auckland Park 2006. The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by v. c. H. R. BRERETON. Published in the Journal November 1973. AUTHOR'S CORRECTIONS The following amendments should be made.

Jan 2, 1974

By A. F. Mulaba-Bafubiandi

Pseudomonas spp was isolated from mine water and tailings samples collected from mining effluents and mine dumps in the Gauteng and Northern provinces of South Africa respectively. Adsorption properties of Pseudomonas spp were then tested for the removal of Cu and Co initially from their synthetic sulphate solutions, subsequently from effluents derived from metallurgical operations. The effects of experimental conditions such as pH, temperature, time, volume and metal concentration on the efficiency of the biosorption process were studied. Absorption of 45% Cu (pH 6, 37°C, 24 hours) and 40% Co (pH 6, 37°C, 24 hours) was observed from solutions with low concentrations (0.07 M). A maximum of 73% and 65% of Cu and Corespectively were recovered from the mine water samples derived from effluents.

Jan 1, 2009