Search Documents

By Robert F. Chaiken, Alex C. Smith

INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) at its Pittsburgh Research Laboratory (PRC) is interested in the application of water mist sprays to extinguish diesel fie1 fires in underground mine diesel refueling areas. To this end experimental studies have been carried out on the extinguishment of diesel fuel fires at PRL's large enclosed fire suppression facility (FSP) at its Lake Lynn Laboratory (LLL). Two sizes of shallow fuel pans (3x3 ft and 5x7 ft) contained the fires, and a number of commercial mist spray nozzles (at roof locations) and spray/fire locations were tested (52 fires in all). Visual observations of the pool fire extinguishment process by the overhead sprays with an infra-red sensitive videocom suggests that there are two distinct actions involved in extinguishment due to two different transport mechanisms by which the water droplets can enter the fire plume. First, is a direct injection of water droplets into the plume from overhead. This is believed to involve larger water drops and leads to an extinguishment time of several minutes. Second, is an indirect injection process involving small water drops which are entrained in the sideways air flow that feeds oxygen to the fire. This second process apparently leads to relatively fast quenching of the fire in less than 1 minute - a highly useful attribute for a fire protection system. This paper describes a relatively simple parametric model for the indirect water injection process, and defines the critical spray conditions for achieving rapid quenching of the pool fire. While the model is consistent with the pool fire data obtained to date, the PRL studies are continuing with more complex pool fire scenarios. It remains to be seen if this simple parametric approach applies to these future fire tests. THEORETICAL Critical Drop Size In the two-dimensional representation of figure I, an oil pool fire is considered to be a cone whose base is the vaporizing liquid oil surface having an area n?, above which exists a fire plume diffusion flame) of height, L. The rising plume induces a horizontal air flow into the side of the plume supplying the oxygen necessary for propagating gas phase combustion reactions. Water droplets suspended in the air around the plume will tend to follow the horizontal air flows into the plume. The rate of air entrainment by the plume will be determined by the overall combustion reaction which is assumed to be

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.

By W. C. Smith

The U.S. Bureau of Mines examined previous research on rib stability in an effort to develop a practical approach to understanding, characterizing, and controlling weak rib conditions in underground coal mines. Because success in stabilizing ribs depends on a basic knowledge of how weak ribs behave, the report reviews the mechanics of rib failure and the relationship of coal mine geology and pillar constraint to rib instability. Strategies for choosing an effective method of rib support are considered, and various rib support methods are discussed. Finally, the report documents techniques for monitoring ribs and use of models to assess rib stability; such monitoring and modeling can also help determine the most effective method for roof support.

Jan 1, 1992

By Steven E. Mischler

The exposure of mine workers to diesel particulate matter (DPM) and gases is an issue of great concern to the underground mining community in the United States. Approximately 30,000 underground miners are potentially exposed to high concentrations of DPM. In January of 2001, the U.S. Mine Safety and Health Administration (MSHA) promulgated rules setting compliance standards for both underground coal and metal / nonmetal mine workers. As industry works to achieve compliance with these standards, mine operators are looking for feasible methods for reducing DPM concentrations in their mines. In addition, the industry needs methods to accurately measure DPM to ensure that the control strategies they adopt are working successfully. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to evaluate control technologies and monitoring instrumentation that can be used to reduce the diesel particulate matter (DPM) exposure of mine workers. An overview of the strategies being utilized in underground US mines to reduce DPM concentrations will be presented. Also, updates on the development of diesel monitoring instruments such as the continuous elemental carbon monitor or the Personal Dust Monitor for DPM measurement will be provided.

Jan 1, 2010

Objective: To improve the effectiveness of dust collector capture on surface mine drills.

Oct 1, 2005

By M. Brnich, L. Mallett, C. Vaught, K. Kowalski

This paper discusses the data collected during an emergency evacuation training exercise at an underground mine in the United States. The focus of this paper is on the human reaction to smoke and the use of personal protective equipment. Specific issues related to the human stress response during an emergency will be discussed.

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By R. V. Ramani, A. S. C. Owili-eger

The origin of gaseous hydrocarbons in coal, predominantly methane, can be traced to the natural processes of coalification. The higher rank coals or the more deeply buried seams retain more gas than low rank coals or shallow seams. It is estimated that up to 460,000 cubic feet of all types of gases are produced during the formation of one ton of coal (Cervik, 1969). The chief components of these gaseous products are methane, carbon dioxide, nitrogen and water vapor. Most of these gases escape during the various stages of decomposition but with eventual presence of overlying impermeable beds, there may be as much as 2,000 cubic feet of gas retained per ton of coal. Over geologic time, diffusion and other processes such as geologic disturbances in the earth's crust remove all but 500 to 2000 cubic feet of gas per ton of coal (Cervik, 1969). It is this residual methane which is of primary concern when mine openings are made in coal measures. Extensive data compiled by the United States Bureau of Mines reveal that some coal mines in this country emit up to 20 million cubic feet of methane per day (Spencer, 1970; Irani et al, 1972). Toxic, poisonous and respirable gaseous pollutants and explosive gases, predominantly methane, are injected into the ventilation stream from active sections and gobs. The liberation of methane in gob areas may, under certain circumstances, become extremely large. In some instances it may constitute up to 70 percent of the total yield of gas in a mine. The basic physical factor which determines the yield of gas into the mine environment is the gas content of the seam. The influence of the gas content of a seam on the overall yield of gas

Jan 1, 1974

By Howard M. Stainer

Jan 1, 1963

By Howard M. Stainer

[Cover Page]

Jan 1, 1963

Objective To characterize the roof fall risk associated with underground limestone mining. Background During the first 5 years of this decade, more than one-fourth of the underground mining fatalities occurred as the result of fall of ground. The large openings in underground stone mines present limitations in observing ground conditions because of floor-to-roof heights ranging from 20 to 60 ft or more. Generally, the status of ground conditions in under-ground stone mines is based on observation and experience obtained during mining development. Some mines use monitoring instruments to gain information on roof conditions, but this practice is typically focused and localized to address issues in a particular area or section of the mine. The Roof Fall Risk Index (RFRI) described here provides a method of systematically characterizing the risk of roof falls to enhance the safety of mine workers. Approach As in many industries, a defective product signals the potential for failure. Similarly, defective rock or strata in an underground stone mine presents a potential risk. Assessing ground conditions relative to the concentration of defects observed provides a way to index or rate these conditions and the subsequent risk. Through observations at approximately 50 underground limestone mines in the United States, strata defects were categorized to develop a quantitative method for determining the RFRI. This method is specifically geared to underground lime-stone mines because strata defects are difficult to see and limited by the experience and knowledge of the observer. Overall, 10 defect categories were deter-mined: 3 that relate to geology, 4 that result from mine development, 2 that are indicative of the roof profile, and 1 that addresses moisture or water flow (see RFRI Chart 1). The defect categories are also weighted to reflect the conditions indicative of roof or strata movement or separation (categories 4 through 8). These weights are multiplied by the assessment value to determine the total category value. The benefit of using monitoring techniques to gain information on roof conditions is also factored into the RFRI for overall assessment of an area in the mine. Each defect category is assessed with a value of 1 to 5 based on parameters as defined in each defect category, with 5 indicating the highest degree or level of defect. The assessment value of 3 is also used when information on a parameter is unknown. The parameters for the defect categories are illustrated in RFRI Chart 2 for use in determining the assessed value. How It Works The RFRI provides a means to categorize the risk for roof falls in underground stone mines. The concept of this calculation is aimed at providing an indication of the level or degree of defect relative to the area of the mine examined. The RFRI for the calculation produces a distribution where RFRI values approaching 0 represent a stable condition and those ap-proaching 100 represent an unstable condition.

Oct 1, 2006

By John D. Sullivan, Edward P. Barrett

The experimental work on the utilization of tin-plate scrap at the North- west experiment station of the U. S. Pireau of Mines in cooperation with College of Mines, University of Washington, necessitated the selection of a simple method for the determination of tin in the iron produced. Some of the standard methods for the determination of tin which were tried are given below: 1. Dissolving in acids and precipitating the tin as sulphide, igniting and weighing as Sn02. 2. Dissolving in aciis, reducing with nickel, cooling in an atmosphere of carbon dioxide, end titrating with standari iodine solution. 3. Dissolving in acids, precipitating the tin as sulphide, dissolving this sulphide in H3 and H2S04, heating until fumes of 503 are evolved, reducing with nickel or sheet lead, cooling in an atmosphere of carbon dioxide, ani titrating with a standard iodine solution.

Mar 1, 1923

By L. D. Gehi, A. W. Khair, M. Ahmad

"Bit wear presents problems to mining operations because it affects both productivity and economics. Most bit research deals with energy requirements and energy dissipation mechanics for ideal fragmentation during the cutting process.Mechanical cutting leads to dust generation. Past studies involving dust generation due to bit wear concluded that dust concentrations increased considerably after a 7% bit weight loss: leading researchers recommend that the bits be changed at that point.Bit wear is affected by three factors: machine operating parameters in-situ mining conditions and rock properties. Operating parameters such as the depth of cut tool material spray position and the drum's rotating velocity are very important and have a definite impact on bit wear.During the mining process the amount of rock in coal and the strength of that rock is important as abrasion and adhesion take affect. Diffusive wear or deformation becomes dominant only when the temperatures exceed critical. Temperatures rise as a function of drum velocity rock properties and the cutting tool itself.Miner bit surveyIn this study, 15 mines were surveyed, and of those six responded for nine seams. The survey reflected a wide range of information about coal production and bit consumption from continuous miner sections. Also used bits were collected to get first-hand information to analyze wear."

Nov 1, 1995

The Crow Indian Reservation is located in the southeastern part of Montana, stretching from near Billings, in the center of the state, to the Wyoming border in the south. The Office of Surface Mining's Casper, Wyoming, Field Office is responsible for regulating mining and reclamation on Crow tribal land. Federal legislation enacted July 11, 1987, authorized the Indian tribes to implement approved Abandoned Mine Land Reclamation Programs. In early 1988 the Crow elected to develop an Abandoned Mine Land Program under the Title IV provisions of SMCRA. The tribe's plan received final approval on January 4, 1989.

Jan 1, 1992

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By N. S. Dalal, W. Irr, X. Shi, V. Vallyathan

"Inhalation of crystalline silica is associated with a biphasic biologic response of acute cell injury and chronic pulmonary fibrosis. Dust induced cell membrane injury leading to the release of lysosomal enzymes and cell death has been implicated as the initial important biologic event triggering the fibrosis. However, it ls also possible other biologic reactions could alternatively, or in addition to these enzyme related cytotoxicity reactions, alter the normal functioning of cells. It is well known that phagocytic activation results in the production of oxygen radicals which are highly cytotoxic to cells. In healthy - lung, protection against the toxic effects of the normal balanced ·biologic reactions are provided by a number of defen1e systems including antioxidants. In disease or condition of overproduction of oxygen radicals, biochemical protection may be overwhelmed with resultant cellular injury.Our recent observations have shown that reactive oxygen radicals (ROR) are generated during grinding of crystalline silica. We hypothesized that these newly generated RORs may cause cell injury, lipid peroxidation, or even damage to macromolecules such as DHA. Biochemical aberrations caused by the inhalation of crystalline silica with ROR at occupational settings might overwhelm cellular and antioxidant defense systems of the lung leading to injury and subsequent fibrosis.To test this hypothesis, we have investigated the generation and decay of ROR produced by crystalline silica using electron spin resonance (ESR) and investigated its toxicity with conventional biologic tests at various time intervals after grinding. We also studied the decay of these newly generated RORs in buffer and the effect of antioxidants and scavengers in the abolition of cellular damages."

Jan 1, 1989

Lower the respirable dust exposure of longwall shearer operators by use of a modified head to tail cutting sequence. Approach Modify the cutting sequence of double-drum shearer operations cutting unidirectionally head to tail, so that the tailgate drum is used to mine the entire coal face except when cutting out at the head. This approach would place the primary dust generating source, the cutting action of the drum, on the return air side of both shearer operators. How It Works Currently, 75% of the double-drum shearers in operation employ a unidirectional cutting sequence. On half of these operations, the primary cut is taken as the shearer travels from the headgate to tailgate ends of the face, with roof support to be advanced on the intake air side of the shearer. Typically, the leading (tailgate) drum is taking a full cut during the head to tail pass and the trailing (headgate) drum is cutting bottom coal. In this mode of operation, the dust generated by the trailing (headgate) drum can spread out into the walkway, and increase the respirable dust exposure of both head and taildrum operators. As an alternative, if the trailing drum is "free wheeling" or cutting minimal coal during the head to tail cut, and bottom coal taken by the tailgate drum during the tail to head clean-up pass, both operators are able to work on the intake air side of the primary dust generating source (drum) except when cutting out at the head. This modified cutting sequence would save wear on the conveyor and help to eliminate overloads, as well as reduce the respirable dust exposure of both shearer operators. This modifcation is only applicable to long-wail operations currently cutting unidirectional head to tail, and to those operations where this unidirectional cut would not produce operating constraints.

Jan 1, 1981

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973