Search Documents

By Joseph A. DeCarlo

This information circular presents data for 1960 on individual coke plants in the United States. All oven-coke plants in existence, whether active or idle at the close of the year, are listed in this report. With two exceptions, only beehive plants on which reports were submitted to the Bureau of Mines are included. Although the Bureau was unable to obtain reports from these two active plants in 1960, the number of ovens and annual coke capacity are estimates, based on previous reports filed with the Bureau of Mines. Accordingly, there were 73 oven-coke plants in existence at the end of 1960 of which 70 were active. Reports were received on 44 beehive plants of which only 13 were in operation at year end. Oven-coke plants are listed alphabetically by States in table 1 which shows the name and address of the company, location of plant, classification or type of ownership, number and type of ovens, annual coke capacity, and coal-chemical materials produced. The terms "furnace" and "merchant" plants used in this and all other reports of the Bureau of Mines designate the type of ownership. Furnace plants are those owned by iron and steel companies whose main business is production of coke for use in their own blast furnaces. Merchant plants are those associated with chemical companies, gas utilities, as well as those that produce for sale on the open market metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials. The annual coke capacity shown for each plant in this table is based on the minimum coking time necessary to produce coke with qualities suitable for its intended use. Therefore, the annual capacity of a plant may change from year to year, depending on age and condition of ovens, the character and quality of coal carbonized, the grade of coke required, and other factors. For example, annual coke capacity of a coke plant primarily making foundry coke with longer coking cycles would be lower than one making blast-furnace coke. Also some ovens must be operated at slightly lower than normal flue temperature because of the condition of the refractories and maximum capacity would be somewhat lower than designed capacity. For this reason, the capacity reported to the Bureau of Mines may differ from the designed or rated capacity estimated by the coke-oven builders at the time of construction. For example, if the generally accepted standard coking rate of one inch per hour were used on all ovens to calculate total annual capacity, it would have been 80.4 million tons or 2 percent higher than the capacity reported to the Bureau. Because of the factors mentioned above, the annual coke capacity shown in this table is believed to be a reliable measure of the practical operating capacity of the industry.

Jan 1, 1961

By Doris M. Hyde

Belize remained relatively insulated from the social and political turmoil that affected some of its Central American neighbors. This stability encouraged new foreign investments that assisted the economy, especially in tourism and agriculture. The mineral sector remained limited to construction-oriented materials. Oil exploration efforts continued by the various concessionaires.

Jan 1, 1987

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Center are developing ways to protect the health of miners. Part of that effort is improving the air quality in metal/nonmetal mines by developing proper ventilation techniques. The air quality of large opening nonmetal mines can be greatly improved by using engineering controls of contaminant prevention and proper ventilation techniques. Contaminant prevention includes methods to reduce contaminants from entering the mine air. Ventilation can be improved with appropriate fan selection and fan operation used in conjunction with air coursing using manmade and insitu rock stoppings.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Thomas P. Meloy

"This paper presents an interim progress report on our recently begun research project on respirable dusts. We are reporting on a sophisticated, predictive, probably correct, testable hypothesis that postulates a mechanism by which some natively cytotoxic respirable size mineral particles, such as kaolin, are not harmful to the lungs, while other equally cytotoxic particles, such as quartz, are, even in small quantities, very harmful. In essence the hypothesis predicts that some mineral particles, not normally present in the earth's ambient dust, causes the lungs dust defense mechanisms to turn on the lung and harm it. However fruitful the hypothesis may be, it is a hypothesis and much work remains to be done before it can be accepted as a theory.While I may make the presentation and be the PI, my co-PI, Dr. William Wallace of NIOSH, has and will continue to make at least as much contribution to the project as I. Our sophisticated hypothesis is deeply scientifically based and unfortunately, in spite of the multifacited aspects of this project, there is virtually nothing in the literature to guide our work. This means we must go back to the classical physics to develop the models for calculating the powerful electrical effects near particle edges, and we must measure the fundamental biological constants associated with pulmonary macrophage. While there are daily discussions on Boltzman distributions, Einstein's Brownian Motion paper, the Nernst Equation, and sophisticated semi- in vivo biological time constant measurements, we are aware that this is not an easy problem and we are not likely to have irrefutable closed solutions to these problems by next Monday morning.HypothesisLet me now turn to our hypothesis. In order to occupy all the naturally occurring surface areas on the earth, man, during his long evolution from fish, had to evolve effective defenses against all the naturally occurring cytotoxic rcspirable mineral dusts. For example, clays, which are often the main component in naturally occurring respirable mineral dusts, are quite cytotoxic but do not harm the lung. However, for respirable mineral dusts that contain significant amounts of nonnaturally occurring but equally cytotoxic quartz and asbestos particles, the body has not had to evolve- an effective defense mechanism, and thus respirable mineral dusts containing these particles may harm the lung. Our hypothesis is, therefore, that a few nonambient minerals such as quartz, cause the bodies dust defensive system to harm the body in a manner analogous to Lupus or MS, diseases of the immune system."

Mar 1, 1989

By Kenneth P. Klouse

The current rulemaking on mine illumination makes it necessary for mine personnel to have an understanding of the behavior of light. They must be able to understand many terms that are new to the industry and must be familiar with the use of various types of photometers. With this knowledge, the enforcement criteria for mines can be understood and compliance can be maintained.

Jan 1, 1976

By W. R. Reed

Dust dispersion modeling is a subject that has had a large amount of research activity. Much of the research has focused on large-scale global or regional dispersion models. Other models have been created for industry-specific purposes. Furthermore, some of the past research has focused on dust dispersion modeling in the mining industry. This report presents the various dust dispersion models that have been developed specifically for the mining industry. The report first gives a brief background of the regulatory environment that helped to promote development of such models. It then presents an overview of the mathematical concepts used in this dispersion modeling. Finally, each of the various models developed for the mining industry are described, along with their associated mathematical algorithms and any field validation conducted on the different models.

Jan 9, 2005

By G. S. Rice, H. P. Greenwald

"Experience and experiment have goth shown that a cloud of coal-dust in air can be inflamed and an explosion developed only when a certain minimum concentration of the dust in air has been equaled or exceeded. Those who have had experience in the handling of coal know that dust is frequently present in the air and may be of sufficient density to obscure an ordinary electric light at a distance of 40 or 50 feet; yet flames may be, and times without number have been, introduced into such clouds, when no additional coal-dust has been stirred up, with no effect other than the burning of the dust particles which actually enter flame. Evidently the density of the dust cloud is insufficient to give self-supporting combustion.The minimum amount of dust in air required to give a spreading flame will vary with a number of factors such as the composition of the dust and its size. This amount in a unit space may be considered analogous to the lower limit of inflammability of fire damp (methane) in air, although the variation in limit of explosibility of gas is small even when conditions of the experiment are altered. In large-scale determinations of the lower limit of inflammability of coal-dust there is no certain method by which a sample of the dust cloud can be snatched and its density determined. It is necessary to produce the best possible dust cloud from a known weight of dust, in a known volume and assume - probably with considerable error - that the dust cloud is reasonably uniform. The dust cloud must be formed and the source of ignition applied to it simultaneously; this is generally accomplished by the use of blow-out shots of black blasting powder, dynamite, or similar explosive so prepared as to blow out like a cannon shot, or by a gas explosion. The more violence attending the source of ignition, the greater is the probability that all the dust is raised in a uniform cloud; and the greater the length or intensity of the flame, the greater are the chances of ignition. As a result one may obtain a variation in apparent minimum density with different sources of ignition. This difference is more apparent than real and must remain until devices for instantaneous sampling of dust clouds during explosions are perfected."

Aug 1, 1931

By BUREAU OF MINES

The Bureau of Mines, in its investigations of respiratory apparatus for use in mines and allied industries; tests equipment that is voluntarily submitted by manufacturers in accordance with published schedules of tests. These tests are designed to insure that the equipment has the minimum requirements for safety in use. Approval certificates are issued for apperatus that meets the bureau's specifications, and the manufacturer is permitted to mark his equiment with a seal showing that it has been approved as "Permissible." A complete list of per- missible self-contained oxygen breathing apparatus, gas masks, and hose masks tested prior to January 1, 1930, was published in Bureau of Mines Information Circular 62309. The present list includes all equipment tested and approved prior to July 1, 1930.

Sep 1, 1930

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

Jul 1, 2003

By Dana Reinke, William Wiehagen, Launa Mallett, Charles Vaught, Kathleen M. Kowalski, Michael J. Brnich, Lynn Rethi, Lisa Steiner

Safety and health professionals from all sectors of industry recognize that training is a critical element of an effective safety and health program. A major concern in the mining industry today is how to train the present aging workforce plus the expected influx of new and less experienced miners and mine operators as the cohort of older workers retire. This paper defines the problem, offers a model to structure the inquiry, and presents the key issues a multi-disciplinary team of NIOSH researchers identified, based on an extensive review of the current literature in relevant areas. Issues include differences between cohorts, such as the newer workers (Generation M), and present workers (Boomers) with respect to their physical, social, psychological, and cultural characteristics, their learning styles and work expectations. Specific issues for an aging workforce are discussed. Some preliminary recommendations are offered on the type of training needed.

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.