Search Documents

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

By Rad B. Langston, Ted J. Williams, John A. Marjerison, Rimas T. Pakalnis, Tom M. Brady, Doug C. Bayer, Mark J. Bren

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

By Ann G. Kim

Methane in coal constitutes a serious hazard in coal mining. Draining the methane in advance of mining can mitigate this hazard, conserve energy, and offer economic benefits. This Bureau of Mines report evaluates the Pittsburgh coalbed in Greene County, Pa., to determine if advance drainage is feasible. The gas content of virgin reserves in Greene County is estimated at 100 to 200 ft3/ton, a total of over 370 billion ft3 of gas in an area approximately 310 mi2. Because of the similarity to natural gas, drained coalbed gas could be recovered and added to pipeline supplies of natural gas. The value of conserved gas would offset the cost of drainage and extend energy resources.

Jan 1, 1975

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

By M. Gottlieb, P. Metes, Charles Sabine, Louis J. Denes, B. Kaminsky, Jami M. Girard, Ronald T. Mayerle

A significant risk factor in assessing and modeling potential catastrophic slope movement in open-pit mines is the presence of argillic alteration in host rocks. High-resolution hyperspectral imagery operating in the visible to shortwave infrared can be a useful tool for identifying and mapping potentially dangerous argillic zones. We have conducted preliminary experiments with a new type of hyperspectral imager that employs an acousto-optic tunable filter, a variable retardation plate and a standard digital camera. The instrument we tested operates in the .5-1.0 micrometer range. A shortwave infrared instrument is planned, and mid-infrared instruments have been designed. An AOTF consists of an acoustic transducer that generates an acoustic wave that propagates through an attached crystalline substance. The wave sinusoidally modulates the refractive index of the crystal, selectively diffracting incident light according to its wavelength. The instrument also measures polarization signatures of reflecting surfaces as well as their spectral properties, opening up new areas of possible research. Images can be acquired and processed at 30 frames/second. The AOTF camera system offers numerous advantages to geologists. It can be used as an airborne imager or as a portable field device to image pit walls, outcrops, rock specimens or drill core. It can be adapted to image polished sections under a microscope, and it could be used in underground workings. Algorithms can produce processed images in real time (e.g., ratio images), and, because it is a camera system, aerial images can be orthorectified.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Mine ventilation can be broadly defined as the branch of mining engineering primarily concerned with the controlled flow of air through mine airways to maintain an acceptable atmospheric environment wherever men work or travel underground. Martinson (1976) has defined three elements of mine ventilation, 1) an engineering element concerned with establishing quality control (removal of dust and gases), quantity control (regula¬tion of air direction and magnitude) and climatic conditioning (temperature-humidity control), 2) a biological element in which an understanding of biological response is used in assessing the mine environment, and 3) a philosophical element requiring judgements as to the degree of risk or worker discomfort that is socially acceptable. Most texts on ventilation, such as Hartman (1961), limit themselves to a discussion of the engineering element. Although also limiting his text to engineering control, Weeks (1928) thoughtfully addresses the other elements in the preface of his book where he states: "Life is brief and happiness elusive under the best of conditions; so beside the commercial aspect must be placed the humanitarian. Is it not reasonable that the operator should give his men a chance to spend their working hours in a comfortable environment, with the danger of sudden death or disability reduced as much as possible?" The statutory requirements of ventilation are, in most countries, established on the basis of biological response as determined by basic research or are dictated by social awareness, often touched off by major disasters, resulting in demands on regulatory bodies for more stringent requirements. To a limited extent, the philosophical and biological elements of ventilation are intertwined in that social awareness may

Jan 1, 1977

By Oliver Bowles

"The introduction into mines, quarries and manufacturing plants of machines and tools operated by compressed air has revolutionized methods of operation to an extent comparable only with that occasioned by the invention of explosives and the utilization of electricity. The use of compressed air in pneumatic tools, in rock drills, and for the operation of pumps and other machinery is well known to most miners and quarrymen, but its application as a substitute for explosives for breaking rock in a few granite quarries has received little publicity.In the region of Lithonia, a few miles from Atlanta, Georgia, is a dome of massive granite used widely for building stone and for paving blocks. The most remarkable structural feature of the granite is the absence of joints and sheeting planes. The term ""joints"" is applied to open fractures that commonly occur in rocks, usually vertical in direction or nearly so, and spaced from a few inches to several feet apart. On the Lithonia granite outcrop, however, one may walk over the bare rock surface for hundreds of feet without finding any indications of a joint, ""Sheeting planes"" are open fractures at various levels, approximately parallel with the rock surface. The presence of such planes when spaced several feet apart greatly facilitates quarrying, and where absent, as at Lithonia, the necessary fractures must be made artificially.The forcing of artificial sheeting planes is accomplished as follows: Two holes of about 3-inch diameter arc drilled close together and to a depth of about 8 feet. Two men work at these holes all summer, and sometimes part of a second summer. A very small charge of black blasting powder, not more than a spoonful, is placed in each hole, tamped with clay, and the charges are fired simultaneously with an electric battery. This starts a small fracture running outward from the bottoms of the holes. There is in most granites one direction of easy splitting known among quarrymen as the ""rift"", and as the rift direction in the Lithonia granite is horizontal the fracture follows a horizontal plane,"

Aug 1, 1920

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

By James R. Wait

It is the purpose of this paper to review theoretical model concepts in through- the -earth transmission of electromagnetic waves. While the subject is very broad in its defined scope, we will be conscious of the specific applications to mine rescue and emergency telecommunications in coal mine environments. The plan of the paper is to outline previous theoretical efforts without attempting to attach names or organizations to the specific developments. However, we include a guide to the literature as an appendix. Without pretending to be entirely impartial we include a critique of the limitations of the available analytical models. As I see it the central problem is to calculate the steady state mutual impedance of a four-terminal network that is the black box characterizing the through-the-earth path. Problems of secondary importance include the determination of the input impedances of the two pairs of terminals and the associated transient responses. [ ]

Jan 1, 1973

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

Develop a user-friendly, personal computer-based numerical modeling program that performs structural analyses of underground tabular deposits, making these readily available to the mining industry. Background When ore is extracted from an underground mine, the overburden weight is redistributed to unmined areas, recompacted gob zones, and artificial structures such as packwalls and/or cribs. This redistribution of stresses continually changes throughout the mining cycle and can be especially complicated when multiple-seam mining is involved. Numerical mine structural analysis methods provide a way of calculating the redistribution of overburden stresses and the resulting loading for any given area of an underground mine, thus enabling engineers to design safer and more productive mines. In 1973 Crouch and Fairhurst developed a mine structural analysis computer program called MINSIM. This computer program was based on the three-dimensional displacement-discontinuity approach, a subvariation of the boundary-element method. In 1979 Sinha expanded MINSIM's capability to provide an analysis of parallel multiple seams. Sinha called his program MULSIM. During 1984 and 1985, the Bureau of Mines upgraded and completely restructured MULSIM into what is now called MULSIM/BM.

Jan 1, 1990

To quickly and reliably assess the stability (safety) of saturated and unsaturated tailings pond embankments. Approach Determine embankment geometry and soil properties, then use that data to obtain the safety factor of the embankment directly from one of a series of factor-of-safety charts.

Jan 1, 1982

Reduce permanent hearing losses to bulldozer operators. Approach Two types of noise control packages have been developed, that can be readily fabricated and installed into bulldozers by mine personnel. How It Works Both of the noise control packages reduce the noise exposure of the operator by two techniques, blocking the noise paths or absorbing the sound before it reaches the operator. Both airborne noise paths and noise paths through the machine are blocked. One noise control package is designed for bulldozers having ROPS (Roll Over Protection System), but no cab. The other package is designed for bulldozers having ROPS

Jan 1, 1981

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

By Edward A. Barrett, Lynn L. Rethi

From 1987 through 1996, 13 fatalities occurred at underground operations in the U.S. stone mining industry. A review of the underground limestone mine industry data for this 10 year period indicated a high fatality concentration in one area: ground failures.

To clean coal mine air by developing a low-cost scrubber suitable for belt transfer and similar applications. Approach Design a scrubber operated by water only, with no moving parts. Use conventional water spray nozzles located within a duct to both move and clean the air. Use a droplet eliminator to get the water droplets and mist back out of the airstream. How It Works Conventional scrubbers require a mechanical fan driven by either an electric or a hydraulic motor. They also require water sprays and some type of scrubbing mechanism. The water powered scrubber, however, offers higher reliability over conventional scrubbers since it utilizes the water sprays to both move the air and scrub the particulate from the air. Conventional water spray nozzles are placed near one end of a rectangular duct open at both ends. The sprays are directed towards the far end of the duct where a stationary wave blade water droplet eliminator is located. Movement of the water spray droplets coming from the nozzles generates (by momentum transfer) an air movement In the same direction as the sprays. The volume of air moved Is primarily a function of the duct cross-section size, water pressure and water

Jan 1, 1981

By M. J. Ferrante

New data on zirconium tetraiodide (ZrI4) have resulted from high-temperature enthalpy and X-ray powder diffraction studies conducted by the Bureau of Mines. These studies were undertaken as part of the Bureau's efforts to provide important thermodynamic data essential to the advancement of mineral resources technologies that can be employed with minimal energy requirements and minimal environmental degradation. Enthalpies were measured with a copper-block drop calorimeter. No transitions or other anomalies were found. Tabulated values are given from 298.15 to 772 K for relative enthalpy, heat capacity, entropy, and Gibbs energy function. Enthalpies are expressed in equation form and combined with data from the literature to calculate values of the standard enthalpy of formation and the Gibbs energy of formation. X-ray powder diffraction data indicate that ZrI4 is primitive cubic with a lattice parameter of 11.79 A and is isostructural with stannic iodide (SnI4).

Jan 1, 1980