Search Documents

Develop design and support guidelines for coal mine entry intersections based upon results of integrated field and numerical modeling analyses of structural parameters for improving ground stability. Background Underground coal mines contain a large number of entry intersections. Dome-shaped zones over the intersections are unstable and are often associated with roof falls. These roof falls may occur during mine development, trapping equipment and endangering miners. These high-risk areas of the mine account for 10 pct of the total number of ground-failure-caused fatalities. The falls, ranging from heights of 1 to 20 ft, cause high dilution and slow the advance rates. Stability at intersections is influenced by four structurally interrelated parameters: in situ stress, geological discontinuities and physical properties, intersection geometry, and roof span. Because of the complex interaction of these parameters, the actual mechanism of roof failure may vary considerably, depending upon the roof lithology, rock strength, and stress conditions.

Jan 1, 1990

Eliminate the occurrence of false fire detection alarms caused by the operation of diesel-powered vehicles in underground coal mines. Approach Fire detection systems used in underground mines are based on measurements of airborne combustion products such as carbon monoxide or smoke particles. The effectiveness and credibility of these systems can be reduced by the occurrence of false alarms that result from the operation of diesel-powered equipment, which produces the same combustion products. False alarms end up being very costly to the mine operation in terms of downtime and labor needed for verification. To improve upon current fire detection systems used in the presence of internal combustion engine products, the U.S. Bureau of Mines developed a fire detector that can discriminate between the occurrence of real mine fires and the presence of engine smoke.

Jan 1, 1989

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984

Develop new technology to encourage domestic processing of automobile catalytic converters for recovering platinum -group metals. Background Automobile catalytic converters are used to convert pollutants in automobile exhaust into water vapor, carbon dioxide, and nitrogen, About 1 million troy ounces of platinum-group metals arc used each year in the. United Slates to manufacture catalytic converters. It has been estimated that about 60 pct of the used catalytic converters arc being collected. Most of these used catalytic converters were not processed in the United States but were exported to Japan or Europe for processing. In 1991, about 250,000 troy ounces of platinum-group metals were recovered from scrap catalytic converters collected in the United States. Each short ton of decanned catalyst may contain 30 troy ounces of platinum-group metals valued at over $15,000. Development of an economic process for the recovery of platinum-group metals that can be operated on a small or large scale may increase, the percentage of catalytic converters collected and encourage domestic processing to recover a platinum-group metal concentrate. This would significantly decrease the dependence of the United States on imports for these critical and strategic metals.

Jan 1, 1992

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

Provide a means for continuous measurement and display of respirable dust concentrations in a mine so that when high dust levels occur, timely, corrective measures can be taken. Approach Develop a personal dust monitor that (1) is small and light enough to be worn by a miner, (2) has the capability to continuously measure the respirable fraction of coal dust, (3) will display the respirable dust concentration in mg/m3, and (4) can store the average respirable dust concentration and sampling time of several sampling shifts for later play-back. How It Works The personal dust monitor (PDM-1) uses light scattering and convection air currents to sample the respirable fraction of coal dust. Convective air currents cause dust laden air to pass through an open-celled sampling chamber (light sensing chamber). A near infrared light emitting diode (LED) located in the PDM-1 emits pulses of light. The pulsed light passes through a focusing lens and glass window into the sampling chamber. The light is then reflected, scattered, and refracted by the airborne dust particles. Light scattered within the angles of 450 to 900 (the angles within which the intensity of the scattered light is most closely related to respirable-size dust particles) passes through another window and is focused on a light detector. The light detector signal is amplified and presented as analog output voltage for conventional recording. This signal is also converted to a digital signal which the microprocessor uses with its crystal clock to calculate the 10-second average dust concentration, the shift average concentration, the time-weighted average concentration, and the elapsed sampling time. The microprocessor also stores dust concentrations of the seven most recent sampling periods, controls the operation of the LED and detector, and operates the liquid crystal display (LCD).

Jan 1, 1983

Reduce longwall equipment transfer time between panels by utilizing a predriven recovery room, and thus eliminate the premove preparation associated with most equipment recovery methods. Background and Approach The recovery point for a retreating longwall is a predetermined position near the end of the panel where mining is terminated and equipment is disassembled and removed. However, to prepare for equipment removal at the recovery point, bolting and wire meshing arc required before the recovery point is reached. Usually, preparations for equipment recovery begin about 35 ft from the recovery point, significantly impeding the normal rate of advance of the longwall and, consequently, production. Recently, BethEnergy Mines, Inc., and the Bureau of Mines cooperated to evaluate the applicability of utilizing predriven recovery rooms to improve longwall equipment recovery. A predriven recovery room is an entry driven parallel to the longwall face at the end of the panel, having standard dimensions (for that particular mine) and supported with bolts, wire mesh, and supplemental support. The preparation of this entry is completed before it experiences mining-induced effects from the approaching longwall face. This enables the face to continue to mine at its normal rate of advance until the panel is completed. The supplemental support is required to control the loads imposed by the front abutment and is the most vital component of the recovery room.

Jan 1, 1989

By Fred Biggs, Walter Utt, Richard Miller

Powered haulage has been, and continues to be, a major source of severe accidents and fatalities at metal/nonmetal surface mines. Between 1986 and 1997, truck drivers accounted for63% of the lost-time injuries in surface haulage. This project was undertaken to reduce the number and severity of lost-time injuries among operators of these trucks. Work involved measuring shock acceleration at a western surface mine during representative work cycles on two types of trucks and collecting data from cab floors using a triaxial accelerometer and from operator seats using a seat pad accelerometer. NIOSH researchers also used the mine’s GPS systems to locate shock events on a mine map in real time. Shock tests were also run at Caterpillar, Inc.’s, proving grounds in Green Valley, AZ, to determine the magnitude of shocks resulting from controlled rock drops onto the bed of a haulage truck.

Wires leading to or from underground facilities can develop hazardous voltages because of lightning exposure. The locations of many mine portals are particularly susceptible to lightning effects. The application of protective devices to limit this potential danger is necessary.

Jan 1, 1975

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By David W. Wisecarver

This report describes a tool to engage and/or place a Bureau of Mines type gage to measure borehole deformation in a horizontal , 1½ - inch - diameter , stress relief borehole . The tool was successfully used at a borehole depth of 105 feet . Practical usage up to borehole depths of 200 feet might be realized . The tool was designed to work inside EX- size ( 1½ - inch ID ) diamond - drill drive casing used as drill rod and through which the deformation gage is guided into an EX- size stress relief borehole . Through laboratory experiments it was found that by exercising a reasonable amount of care the deformation gage could be placed at a point within a ± .01 foot distance of a predetermined depth in a horizontal EX- size hole and that the deformation measuring piston or plunger of the gage could be oriented in the borehole within 0.5 ° of a preselected angle of orientation in a vertical plane .

Jan 1, 1964

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau's engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By M. J. Ferrante

High-temperature enthalpy and X-ray powder diffraction studies were con-ducted on aluminum sulfide (Al2S3) as part of the Bureau of Mines effort to provide new data for the advancement of mineral technology consistent with environmental preservation and energy conservation. Relative enthalpies were measured with a copper-block calorimeter from 298.15 to 879 K. Tabulated values are listed for heat capacity, entropy, Gibbs energy functions, and relative enthalpies between 298.15 and 900 K. Enthalpies were also given in the form of an equation and combined with published data to calculate standard enthalpies of formation and Gibbs energies of formation for reactions of crystalline aluminum with crystalline, liquid, and gaseous diatomic sulfur. The hexagonal, rhombohedral, and cubic phases of Al2S3 were identified by X-ray powder diffraction studies, and the indexed powder diffraction patterns of these phases are given. The hexagonal phase was stable to about 852 K and was partially converted to the rhombohedral form at 879 K.

Jan 1, 1981

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

Improve the safety of roof bolting machine operators working in underground coal mines while maintaining or improving efficiency of the roof bolting operation. Approach The Bureau of Mines funded research under contact to develop equipment that would assure greater safety in drilling holes and installing roof bolts. The research led to the design and fabrication of a roof-boiling machine that allows its operator to per-form drilling and bolting tasks while under permanently sup-ported roof or canopy protection. How the Prototype Works The major components of the remote-control roof bolter are a flexible-shaft drill that provides continuous drilling capability without the need to Stop to add drill extensions for long holes; a roof-bolt inserter that can bend a longer-than-seam height roof bolt into the drilled hole; and a roof-bolt lifter/torquer that completes insertion of the roof bolt into the hole and torques it to the desired tension.

Jan 1, 1986