Search Documents

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

By Wing G. Agnew, John A. Johnson, McHenry Mosier

"INTRODUCTION AND CONCLUSIONSThe first three reports of investigations 5/ in this series, pertaining to the investigation of stemming at the Mount Weather Testing Adit dealt with the dust produced by blasting, the effect of stemming on gases generated by blasting, and the relative advantages and disadvantages of different types of stemming and no stemming when used with 60-percent ammonia gelatin dynamite.This report covers an investigation of the length of stemming material through which a primer will fire and detonate a charge of dynamite, such as a missed hole.The practice of drilling a new hole a foot from a missed hole to blast out the missed hole should be prohibited. It is dangerous, as is evidenced by the number of miners killed through drilling into missed holes. It is even more hazardous in a mine on a multiple-shift basis, in which the same miners do not drill succeeding rounds."

May 1, 1942

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By James E. Hill

TECHNOLOGY is best nurtured by a sympathetic climate that is a composite of many factors. Necessity is a highly motivating factor as illustrated by the abnormal surge of technologic development curing wartime. Other factors include appropriate timing, economic pressures, available personnel, and in some instances, legislative action. Problems of recent concern to mining technology have been the quality and quantity of available technical personnel and the possibilities of restrictive legislation. The quality and quantity of technically trained personnel may be inadequate to meet the rapidly increasing complexity of modern technology coupled with the growing demand for qualified personnel. The question of appropriate training was a subject for debate.2 The curriculum and methods of teaching have changed. Questions have been raised on the relationship of scientist and engineer, interdisciplinary versus specialized curriculum, undergraduate versus graduate training, and the place of the smaller schools versus the large university-research complexes that have developed at some universities. Various aspects of the subject of engineering education for the mining industry were discussed at the meeting on Mining and Mineral Engineering Manpower at the Michigan College of Mining and Technology, November 18-19, 1963. Meanwhile, the trend toward interdisciplinary training gathers momentum as illustrated by the establishment of the School of Engineering Science at Johns Hopkins, the Schools of Engineering and Applied Science at Columbia, Princeton, and Yale, the Division of Engineering and Applied Physics at Harvard and, more recently, the School of Engineering Science at Florida State University which cuts across the conventional areas of civil, mechanical, electrical, and chemical engineering.

Jan 1, 1964

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By E. J. White

Data from oil well logs and core analyses were used to quantitatively evaluate formation porosity and water saturation of heterogeneous carbonates and to study the pore geometry and performance characteristics of cores from these formations. Logs and cores from the Madison limestone from 233 wells in three fields in the Williston basin were used in the investigation. A comparison of log and core analyses shows that log porosities are consistently larger than core porosities, and the differences are correlatable with core porosity ranges. Water saturations from logs are usually smaller than the corresponding core saturations by summation of fluids, but the difference is attributable to mud filtrate invasion into the cores during drilling. Petrophysical studies show that the low permeabilities and high residual water saturations in these reservoir rocks are due to their fine crystalline texture and complex pore geometry (heterogeneity). It is concluded that both log and core analyses must be used for reliable evaluation of these carbonate formations.

Jan 1, 1971

By D. J. Parker, D. Harrington, L. H. Harrison

The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient. points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of, life and damage to property, with special application to the mining industry The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment,, through improved types of lightning arresters,, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures. LIGHTNING PHENOMENA In 1751, Franklin proved that lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition, to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By C. M. K. Boldt

This U.S. Bureau of Mines report presents a study of three typical tailings samples as potential cemented backfill in underground mines. The testing series was unique in that the pulp densities of the samples were all above 75 pct solids. Test results included dry density; slump; percent settling after 28 days of curing; tensile strength after 28, 120, and 180 days of curing; and unconfined compressive strengths after 7, 28, 120, and 180 days of curing. The physical properties of the various test mixtures were further analyzed using linear and nonlinear statistical methods to produce correlations and mathematical equations. Physical properties were used to determine the influence of mix additives and as input for numerical modeling studies of backfill. The mathematical relations were used as a predictive tool in determining the suitability of various materials as backfill.

Jan 1, 1989

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult and longstanding engineering problems associated with coal mining is the catastrophic failure phenomenon known as coal mine bursts (known in the United States as bumps). For more than 70 years, researchers and practitioners have attempted to determine whether this destruction observed underground is caused by stress conditions within the coal pillar or from distant seismic sources in the mine roof and floor strata. The role of confinement and the extent of failure in solid pillars and panels have also proven difficult to define. These are important issues, since control solutions need to be based on a fundamental understanding of the problem. Obsenations by U.S. Bureau of Mines researchers over the last decade have helped to clarify certain aspects of these issues. Microseismic sensors and geomechanic field measurements have located areas of excess energy release, identified stress conditions in coalbeds close to failure, and recorded the response of mine structures prone to bursts. In the present study, data available for a range of U.S. bursts were considered in an effort to evaluate both common and distinctive features. Although the attempt revealed little commonality, encouraging results were produced by categorizing coal bursts by source mechanisms. When a coal burst is thus categorized, differences in environmental factors-such as geology, stress fields, and mining methods-are highlighted, and viable control strategies are readily recognized.

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947