Search Documents

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (U.S.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have increased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

Control dust generated during overburden drilling at surface coal mines using either wet suppression or dry collection systems. Approach For the wet suppression systems, a range of water flow rates was tested over a number of holes. Each hole was drilled at a specific and constant flow rate. A recording flow meter was mounted in the water line near the control system pump. For the dry collection systems, each drill was tested with the front of the shroud set at different heights above the ground. Because of the irregularity of the ground surface, all height measurements were taken at the front of the shroud. Background Wet drilling systems consist of a water tank mounted on the drill from which water is pumped into the downhole air line. The water droplets in the bail air conglomerate dust particles as they travel up the the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole.

Jan 1, 1987

By W. E. Robinson

Oil-shale samples selected from a core of the Green River Basin (Wyoming) were studied to ascertain differences in the composition and/or chemical structure of the organic material in the samples relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble kerogen present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extract and upon the aromaticity of the kerogen. In general, it was concluded that significant differences exist in the chemical structure of the oil-shale organic material from various strata within the Green River Formation of Wyoming. Most of the compositional and structural changes were not related to burial depth but were related to source material variations, environmental differences, or other factors.

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau&apos;s research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982

By Rose L. Ballard

This chapter summarizes data on crude non fuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal non fuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production, The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1986

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003

By John Nagy

The Bureau of Mines examined explosion development in a closed spherical vessel, mathematically correlating flame travel, pressure, and time with parameters defining the reaction. The model assumes that burnt and unburnt zones are separated by a thin, radially moving flame front. Isothermal and adiabatic systems are considered. Correlation with gas and dust explosion data is better for the adiabatic system, but the isothermal development is simpler and in reasonably good agreement. Interpretation of the explosion phenomena is facilitated by expressing the rate of mole change in the flame front in terms of elementary parameters. This expression is developed by examining the components of spatial-flame velocity.

Jan 1, 1969

By Neil B. Young

Analytical results for nahcolite, dawsonite, total extractable alumina, and oil yield are presented for samples representing Green River Formation oil shales in the saline section of two cores from Colorado&apos;s Piceance Creek basin. Analyses are also reported for samples extending the analyzed section of Colorado corehole No. 3 beyond that reported previously. These data permit evaluation of the deposit for possible production of three coproducts--shale oil, alumina, and sodium carbonates--from the saline section of the formation at these sampled points.

Jan 1, 1970

In This Chapter [Ventilation: dilution and displacement Water sprays: wetting and airborne capture Water additives: foam and wetting agents Dust collectors: filtration efficiency and inlet capture efficiency Reducing the generation of dust for cutting, drilling, blasting, crushing, and conveying] [This chapter will give you a general perspective on what works or doesn’t work. The chapter will also help if your dust control problem doesn’t fit any of the circumstances described in later chapters. ] This chapter describes the three major control methods used to reduce airborne dust in tunnels and underground mines: ventilation, water, and dust collectors. It also describes methods to reduce the generation of dust, so less has to be removed from the mine air. The ventilation methods provide the best use of air in the vicinity of workers and in the vicinity of dust sources. In this sense, the methods described are local ventilation methods. Most of the emphasis is on so-called displacement ventilation because it is the most effective dust control technique available. The section on water sprays outlines the dual role of sprays—wetting and airborne capture—and describes why wetting is more important. It also corrects some of the misconceptions about spray effectiveness and describes circumstances where sprays can actually increase the dust exposure of workers. The section on dust collectors outlines the circumstances under which dust collectors can be expected to function effectively. It also describes some common design and maintenance problems. The final section describes how to reduce the amount of dust that gets into the air in the first place, since once the dust is airborne it is always harder to control.

Jan 6, 2003

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today&apos;s coal preparation industry.

Jan 1, 1977

By Kenneth O. Bennington

This investigation is part of the Bureau of Mines research effort directed at advancing mineral technology and minimizing energy requirements for extractive metallurgy. The emplacement of the primary minerals petalite (LiAlSi4010) and spodumene (LiAlSi206) in the lithium pegmatites is examined on the basis of their Gibbs energies of formation determined from lithium metastltcate and oxides, using a series of proposed reactions. The reaction between spodumene, quartz, and petalite (LiAlSi206 + 25i02 [=] LiAlSi4010) apparently does not take place in nature but may be proved experimentally.

Jan 1, 1982

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970