Search Documents

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

Problem: Incident investigation reports do not usually contain enough information to aid in studying boom arm vertical speed for roof bolting machines to determine the impact that appendage speed had on an operator&apos;s risk of experiencing a contact. Laboratory experiments with human subjects are also not feasible because of safety and ethical issues. Method Researchers successfully developed a three-dimensional computer model that uses virtual human simulation software as the primary means to gather contact data when the boom arm touches the operator&apos;s hand, arm, head, or leg. Results: Data analysis of roof bolter simulations shows that the speed of the boom arm is the most important factor in determining the risk of an operator making contact. Regardless of other variables, contact incidents were always greater when the bolter arm was moving up, greater on the hand, and greater for the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom arm is ascending. Based on the data collected, boom speeds greater than 13 in/sec result in a substantial increase in risk to the roof bolter operator of making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Impact on Industry: The use of such information can be quite helpful in making recommendations to machine design and task procedures to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine&apos;s boom arm.

By H. E. Powell

The selective recovery of nickel and zinc from a waste phosphate solution by solvent extraction was investigated by the Bureau of Mines as part of a broad program to recover valuable metals and compounds from industrial wastes, and to reduce the associated land and water pollution caused by dumping these wastes. The waste, which resulted from the phosphation of automboile bodies, yielded 99 percent of both the nickel and the zinc by extraction with dinonyl naphthalene sulfonic acid (DNSA) and di-2-ethylhexyl phosphoric acid (EHPA), respectively. Dilute sulfuric acid was used to recover the metals and regenerate the solvents.

Jan 1, 1970

By T. T. Campbell

This report describes the development of new electroplating baths from which tin-nickel alloy plate was deposited. Although tin-nickel plate can be deposited from an aqueous ammonium bifluoride bath, the corrosive nature of this bath has served as a deterrent to its use. The Bureau of Mines felt that more general acceptance of this new alloy plate would follow if neutral or alkaline baths could be developed. Promising results were obtained from electrolytes containing both tin and nickel chlorides dissolved in triethanolamine-hydrochloric acid or in ethylene glycol hydrochloric acid baths. Current efficiencies close to 100 percent were obtained with these baths. Research revealed that tin-nickel plate could be produced from organic solvents or from mixed aqueous-organic electrolytes. The composition of the alloy deposit - 65 percent tin and 35 percent nickel - was found to exhibit the same single-phase structure that is obtained from the commercially accepted fluoride-type bath.

Jan 1, 1959

By N. E. Hanna

The effect of small percentages of sodium chloride on the incendivity of permissible explosives was studied by the Bruceton up-and-down technique in gallery tests. Both the reduction in incendivity achieved by addition of sodium chloride and application of the test method to explosives evaluation are discussed. It is demonstrated that the up-and-down technique in gallery testing is suitable for distinguishing differences in incendivity between different explosive compositions and between lots of the same composition. The study also shows that addition of relatively small quantities of sodium chloride tends to reduce the incendivity of explosives to firedamp, but addition of sodium chloride cannot insure reduced incendivity. Any improvement attributable to the salt can be counteracted by undefined variations in the explosive. The need for experimental investigations of a number of factors that may affect the safety of permissible explosives is emphasized. ACKNOWLEDGMENTS Grateful acknowledgment is made of the assistance of Roy L. Grant in analyzing for normality of distribution of the data obtained by the up-and-down methods and to Harold E. Tubbs for numerous calculations.

Jan 1, 1959

By E. Chin

Bangladesh, whose population probably passed 100 million by yearend, remained one of the poorest countries in the world, with a per capita gross domestic product (GDP) of $126.2 Its only economically significant mineral production was natural gas. A few other minerals or mineral-based commodities were also produced, generally for local consumption. These included cement, clays, nitrogenous fertilizers, limestone, salt, steel, and pilot plant production of ilmenite and rutile. Exploration for oil was a continuing quest, which was hindered by a lack of funding and a hesitancy on the part of foreign petroleum companies to make long-term or expensive exploration commitments. PODUCTION AND TRADE Production of natural gas continued to increase as more use was being made of the abundant gas reserves variously put at between 7 and 16 trillion cubic feet. The main consumers were nitrogenous fertilizer producers and electric powerplants, but other industries were converting to natural gas from imported coal or fuel oil wherever possible.

Jan 1, 1986

By C. M. McKinney

Sulfur content data from Bureau of Mines routine analyses of 1,060 United States crude oils were used with crude oil production data for the years 1956-66 to prepare tables and charts that illustrate the volume and percentage distribution according to sulfur content of crude oil produced in 10 geographical areas of the United States. Similar relationships for foreign crude oils based on analyses of 201 crude oils and production during 1966 are illustrated for Africa, Canada, Middle East, and South America. Tables are included giving field name, sulfur content, geologic name and age of producing formation, depth of producing formation, and production during 1966 for 882 United States crude oils and 201 .foreign crude oils. Between 1955 and 1966 the average sulfur content of crude oils produced in the United States decreased from 0.73 to 0.67 percent.

Jan 1, 1967

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By Robert D. Schmidt

This Bureau of Mines report describes the development and application of a computer model for simulating the hydrological activity associated with in situ leaching. The model is intended to provide uranium resource developers with a description of the flow behavior of leachants and ground water during the development, production, and restoration phases of a leaching operation involving an arbitrary pattern of injection and recovery wells. Different aquifer environments are modeled, using a closed-form solution to the partial differential equation that describes three-dimensional changes in piezometric head as a result of pumping from leachant injection and recovery wells. The computer program can model a maximum of, 50 arbitarily located wells. Numerical techniques involving difference quotients and Taylor expansions about time points are used to derive time, velocity, areal sweep, and fluid volume parameters associated with leaching hydraulics. These parameters are output by the program in graphic and tabular formats. Other numeric methods insure that the program running time is minimized without significantly affect-ing the accuracy of results.

Jan 1, 1980

By G. F. Kuncir

The funding tables included in this report were defined in support of an evaluation of the Advancing Oil Sale Mining Technology Program undertaken by The Aerospace Corporation. Because of the sensitive nature of the fiscal planning information, the tables have been separated from the main analysis report and given a limited distribution.

Jan 1, 1977

By David R. Hanson

Experimental work performed by the Bureau of Mines in a laboratory environment has shown that the formation of failure zones within certain rock types is accompanied by the emission of significant amounts of radiofrequency (RF) electromagnetic (EM) energy. This radiation was detected using nonresonant, "electrically short," broad-band antennas. Rock types for which emission was observed include granite, quartzite, and taconite; sandstone and marble did not emit measurable radiation. Amplitude spectra of the radiation showed the energy to be concentrated between 10 and 40 kilohertz. These data indicate that emission is directional, but this has not yet been proven. In addition, amplitude of RF emission increases with increasing crack size. Since emission was observed only for brittle quartz-bearing rocks, it appears the formation of piezoelectric fields is a necessary condition for RF radiation. Plausible mechanisms for emission include rapid decay of piezoelectric fields accompanying the sudden stress release at failure and/or the acceleration of an "exoelectron plasma" through the intense local piezoelectric fields. Since emission appears to increase with the scale of failure, and since antennas do not need to be coupled directly to rock surfaces as with conventional geophones, the possibility of developing a portable system to monitor seismically active areas exists.

Jan 1, 1981

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system&apos;s early history.

Jan 1, 1974

By D. S. Kingery

The practice of using doors to control main ventilating currents in bituminous-coal mines is common throughout the industry. When doors are erected in pairs to form air locks, they are usually accepted as satisfactory by both State and Federal coal-mine-inspection agencies. A review of the contributing factors in recent methane ignitions showed that interrupted ventilation (often caused by doors latched open, destroyed, or damaged) was the principal cause of methane accumulations that subsequently were ignited.

Jan 1, 1958

By William R. Sharp

This Bureau of Mines report details a technique for aiding the engineer with the long-range design of an underground mine. The method is based upon the assumption that sufficient data are available to assign numeric values to some finite number of mineralized blocks; assignment of numerical values is problem dependent. By assigning appropriate weighting schemes, the algorithm developed in this report may be used to solve the optimal end-of-life underground mine layout, design least-cost electrical layout networks and efficient material handling networks, find least risk escape routes in the event of an accident, etc. The method is based upon the assumption that sufficient cost and geologic data is available to build a detailed mineral block inventory of the mineral deposit. It is further assumed that the cost assigned to any minable unit is independent of the neighboring blocks. The basic approach relies upon concepts and ideas from the theory of networks. To make the approach user oriented, a computer program is included and discussed. The computer code is written for an orthogonal, three-dimensional set of blocks. Computational costs and experience indicate that the program could be of great benefit in evaluating large complex mineral properties from the viewpoint of predesigning an underground mine layout.

Jan 1, 1974

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By T. M. Kohler, G. L. Finfinger, D. M. Hyman, A. T. Iannacchione

The Bureau of Mines measured methane emission rates from an advancing salt face ranging from 15 to 56 ft3/ton (0.5 to 1.8 m3/t). Small room size, use of a continuous miner, and a well-defined ventilation system made possible air velocity and methane concentration measurements, These measurements, representing data from 18 production days, were con- ducted in an area of abnormally low grade salt, Methane emissions occurred primarily during the advance of the salt face by continuous miner.

Jan 1, 1982