Search Documents

By L. C. IlsLey

The observations made by Bureau of Mines engineers of permissible equipment installed in about 40 mines have indicated a chance for improvement in designs calling for the use of bolts , screws , studs , etc. , especially with respect to bolt sizes and protection from mechanical injury .

May 1, 1931

By Sidney Katell

This report is an economic evaluation of the production of hydrogen in a continuous system by the steam oxidation of partially reduced iron oxide in a fluidized bed at 7 atmospheres using producer gas to reduce the iron oxide. The oxidation-reduction step is based on experimental data obtained by the Bureau of Mines at the Pittsburgh Coal Research Center. The estimated capital requirement for a plant producing 30 million std. c.f.d.3 of 99.8 percent purity hydrogen at a discharge pressure of 450 p.s.i.g. is $13,100,000, using January 1961 equipment cost data. Based on a 330-day operating year, the operating cost before profit and taxes with coal price as a variable is estimated to be:

Jan 1, 1962

By A. Visnapuu

The Bureau of Mines investigated carbonyl processing techniques for the recovery of the critical metals Ni, Co, Mn, and Cr from domestic primary and secondary sources. In most cases, the source materials require reductive precarbonylation treatment to metallize the contained Fe, Ni, and Co compounds to render them reactive with CO. The critical metals were recovered either by direct conversion to the respective carbonyls or as upgraded products by carbonyl removal of an undesirable metal. Best metal-to-metal carbonyl conversion was under CO pressure, from 80 atm upward, and at 1400 C. Carbonylation was accelerated by the addition of HzS in small quantities. CO pressure, temperature, promoter and pretreatment trends, and other factors enhancing metal carbonyl formation are presented.

Jan 1, 1987

By H. P. Greenwald, G. E. McElrey

"Part IV.- The Resistance Caused by Right-Angle Bends. IntroductionThis paper deals with the fourth phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the major results public as rapidly as possible. Parts I, II and III were issued as Serials Nos. 2621 (July 1924), 2647 (October 1904) and 2671 (March 1925) and dealt with the resistance of unobstructed entries, the resistance due to mine cars and, the resistance of timbered entries respectively.Description of the Tests With the last cutthrough between the two butt entries of the test section in the Experimental Mine open, the air flow was deflected, around two right-angle bends in the same direction, the butt entries being 50 feet center to center and approximately 6 by 9 feet in cross section. Each bend had a dead end opening off of it; that at the first bend was in the direction of flow and that at the second bond was at right angles to the flow. For a primary test condition the inner corner of each bend was trimmed square and the dead ends were closed off with board brattices set flush with the line of the cut-through.The two corners of the first band were, then modified both independently and in conjunction. Various modifications of both bends in conjunction were also tested with rather surprising results as to the effect of conditions at the first bend, upon the pressure losses at the second. To confirm the theory developed to fit these results a series of tests were made to give a direct comparison of the -pressure losses as between two bends with the air flow deflected in the some direction at each and with the air flow deflected in opposite directions. The former is designated ""double"" and the latter a ""reversed"" right-angle bend. This series of tests was conducted, however, on the bends at one of the intermediate cutthroughs at which the flow could be deflected us either direction at the second, bend. Here also the average cross-section was 6 by 9 feet and the bends were 50 feet apart."

Jan 1, 1928

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C.5 Safety Equipment and Control Devices Safety equipment and control devices serve two principal functions in mine escape hoists. First, they can be used to provide important safety features such as protection against overspeed, over¬travel and undertravel. Second they can be used to automate or partially automate the operation of the escape hoist. Typical equipment available is described in the following section. 1. Simplex and Lilly Hoist Controllers Manufacturers: Logan Actuator Co. 4956 No. Elston Ave. Chicago, Illinois 60630 312-736-7500 The Simplex and Lilly Controllers provide a means for electrically shutting off the power to the hoist and the energy to physically set the brakes in the event of overspeed, overtravel, undertravel and failure to begin deceleration within sufficient distance

Jan 1, 1976

By C. A. Alien

The increasing activity in oil shale has had a tendency to direct the attention of the industry to any substance from which gasoline or other oils can be secured . Cannel coal for many years has been known, as a source of oil and formerly it was the only substance from which kerosene was obtained . The name of coal oil was given to kerosene because it was derived from cannel coal before any flowing wells were brought in in the United States . In an isolated region in Southern Utah there is an unusually thick and clean bed of cannel coal which laboratory experiments indicate can be made to yield about seventy gallons of oil to the ton . This coal was first described in Bulletin 341 of the United States Geological Survey under the title of Colob coal field . This field lies at the western and southern base of the Colcb plateau and extends from the town of Cedar City southward to Kanarra and then southeastward to the town of Mount Carmel . Cedar City is 35 miles south of east from Lund on the Los Angeles and Salt Lake Railroad which is the nearest railroad point . Mount Carmel is about 90 miles south of Marysvale , on the Denver and Rio Grande Railroad , which is the nearest railroad point from the eastern end of the field . The Colob coal occurs in Lower Cretaceous rocks and a number of wagon mines have been opened on the seam in the vicinity of Cedar City , Kanarra , and Mt. Carmel , but between these places the field has been very little prospected . The cannel coal , so far as known at present , is limited to a small area on the head waters of the north fork of the Virgin River in Township 39 and 40 South , Range 9 East . In this region it occurs as a bed 5-1 /2 feet thick over which lies a layer of bituminous coal 2 feet and 5 inches thick .

Feb 1, 1921

By Howard C. Turnage, Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally of times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 2, 1983

By McHenry Mosier

The Anson Bette manganese mine, with two prominent manganese-bearing outcrops in schist, has attracted considerable attention for its variety of manganese minerals and its possibilities as a potential source of manganese. Little mining was done prior to 1925, when the present owner acquired the property, and operations since that date have been intermittent. Mine workings are open cuts with a maximum depth of 35 feet. The two outcropping ore deposits are irregular, pipelike bodies about 500 feet apart. As nothing was known of the grade or extent of mineralization in depth, four holes totaling 1,072.5 feet of bore Were diamond-drilled by the Bureau of Mines in the summer of 1943, with the results shown in figures 3 to 6. In.1945 a geophysical survey was run to map the magnetic anomalies in the manganese-bearing belt as a means of determining the locations of manganese deposits. Positive correlation of magnetite and manganese ore was not obtained.

Jan 1, 1949

By H. B. Salisbury

The Bureau of Mines conducted research to determine if low-grade California chromite ores could be beneficiated to produce products suitable for commercial use. This research is part of a Bureau goal to provide technology capable of using low-grade domestic ores to meet emergency demands of the Nation for metals and minerals and in particular those minerals, such as chromite, which are considered critical. Two ores from California were ground and treated using gravity concentration and magnetic separation techniques. An are from Auburn in central California, assaying 2.5 pct Cr203, was treated by tabling and magnetic separation to yield a nonmagnetic product containing 44.7 pct Cr203 at a recovery of 36.4 pct. Core drilling samples from the Seiad Creek area of northern California, assaying about 6 pct Cr203, were upgraded by tabling to yield a concentrate containing nearly 50 pct Cr203 with a recovery of 50 pct. Both products are suitable for metallurgical and/or chemical use.

Jan 1, 1981

By Vernon R. Miller

The Bureau of Mines developed and evaluated a detector-sorting device to separate the copper-bearing portion from the barren portion of native copper ores. Small-scale sorting tests were run on minus 1-inch plus 1/2-inch size materials from the following Michigan samples: Winona, Kingston, and Centennial ores, and "poor" rock from the Champion mine dump. Results showed that 60 to 85 pct of the copper was recovered in 9 to 19 wt-pct of the sorted fraction. About 90 pct of the copper recovered was obtained in the first pass through the sorter. For the Kingston and Centennial ores, combinations of sorter concentrates and fines generated during crushing, resulted in recoveries of 93 and 94 pct, respectively, of the total copper in the samples. The combined products constituted about 66 wt-pct of the total sample and allowed the balance to be discarded with only a 6 to 7 pct copper loss.

Jan 1, 1974

By A. W. Effinger

The Bureau of Mines used regression analysis and applied statistical methods in an effort to rationalize the results of an experiment examining the effects of certain variables on carbon deposition in a reservoir for thermal recovery of petroleum. Although none of the 15 trials of the original experiment resulted in the response of weight-percent of carbon regarded by the experimenter as adequate, values calculated using canonical analysis in two trials yielded responses 33 and 54 percent higher than the minimum acceptable figure. The actual responses differed by less than 3 and 6 percent, respectively, from the predicted responses. Methods are described for defining a path of increasing response based on the minimum point and the response surfaces and for defining a set of values for the parameters in question, which result in increased response, A detailed explanation of the mathematical process used in this analysis is presented in the appendix for ease in computer programing the technique.

Jan 1, 1970

By J. E. Zeilinger

The technical feasibility of using energy from explosive ignitions of coal dust to pump water was .demonstrated in an exploratory investigation. Ignition of small amounts of pulverized coal that were dispersed in air over columns of water pumped up to 5.3 gallons of water per cycle when operated against a head of 30.75 feet. Water displacement was accomplished by either manual or automatic operation through a single cycle, and by automatic operation through a continuous series of cycles of I-minute duration. Operating through single cycles, slurries containing up to 3 pounds of coal and 4.6 gallons of water were also pumped. Possible uses of an efficient coal-fired pump would include pumping water for irrigation purposes, removing water from mines, transporting coal from mines in the form of a slurry, and pumping water to elevated reservoirs at electric powerplants so that it could be used to generate electricity during peak periods of demand.

Jan 1, 1966

By H. E. Powell

The mineral dressing research here reported is part of a continuing program by the Bureau of Mines to develop new or improved concentration processes for oxidized or partly oxidized lead and zinc ores. A sample of low-grade sulfide-oxide, lead-zinc ore from Jasper County, Mo., containing galena, cerussite, pyromorphite, hemimorphite, smithsonite, and sphalerite was concentrated by froth flotation and tabling to a grade of 66 percent lead. Because of the presence of a high content of slime-size values, the overall recovery of lead was limited to 64 percent at this grade. Tests to recover the zinc by froth flotation and by gravity concentration did not give satisfactory results. INTRODUCTION Since its establishment, the Rolla Metallurgy Research Center has con-ducted studies of base metals as a part of its overall program (1, 2, 3, 4, 5,6,7).3/ This research has been, and is, directed to beneficiating complex and submarginal ores, to retreating rejects from commercial installations, and to developing fundamental data.

Jan 1, 1960

Lower costs associated with hands-on training in donning and using a CSE ,self-contained self-rescuer (SCSR). Background In June 1987, the Mine Safety and Heath Administration (MSHA) issued an Emergency Temporary Standard (ETS) requiring that all persons entering underground coal mines must be given bands-on SCSR training. The ETS will shortly be replaced by a new standard requiring this hands-on training. Bureau of Mines research has shown that the most effective means of delivering this training is to have the trainee go through a six-step training procedure while in a kneeling position. Once the miner has looped the neckstrap over his or her head, he or she completes the donning sequence in this order: 1) activate oxygen; 2) insert mouthpiece; 3) put on nose clips; 4) put on goggles; 5) adjust neck and waist straps; and 6) replace miner's cap and prepare to move out. This procedure is repeated until the miner demonstrates that he or she is proficient at the task.

Jan 1, 1988

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By M. M. Tilman

The Bureau of Mines investigated the precipitation strengthening of lead¬-base alloys containing 0.5 through 4 weight-percent combined Cd plus Sb. The Cd and Sb were alloyed in a 1-to-1 atomic ratio which maintained compositions along the quasi-binary section Pb-CdSb. Tensile properties, creep rates, and stress-rupture values were obtained on alloys in the aged condition. The highest tensile strength was observed in an alloy of Pb-3 CdSb, After aging for 6 months at 90°±3° F, this alloy had a mean tensile strength of 8,950 psi with 15-percent elongation. An aged alloy of Pb-1 CdSb exhibited a steady state creep rate of 1.2 X 10-3 percent per day at a stress of 500 psi and a temperature of 90°±3° F. Times to rupture at stresses up to 4,000 psi and at a temperature of 90°±3° F were obtained for some compositions.

Jan 1, 1970

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum, The economic development of the country depended on the production and export of crude on. Output was estimated to be 49 million barrels in 1985 compared with 56 million barrels in 1984 and 47 million barrels in 1988. The country's only refinery consumed approximately 12% of the daily production of crude oil while operating at slightly over 50% capacity. The refinery output, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economic prospects were heavily dependent on the oil sector, which bad been responsible for the recent strong growth in the economy. The country consistently sought to avoid the problems associated with an overdependence on oil and followed a relatively broad-based development strategy, using oil revenues to sustain and encourage growth in other sectors. Approximately 75% of the gross domestic product (GDP) was attributed to the mineral industry in some form. GDP growth was approximately 6.5% during 1985.

Jan 1, 1987