Search Documents

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

By L. C. IlsLey, H. B. Freeman

In connection with the approval of coal-cutting machines for service in gaseous mines , the engineers of the Bureau of Mines have been somewhat concerned as to the type of trailing cables that could safely be used on permissible outfits . While no final action has been taken on this question ( tentative approvals having been granted pending investigations ) , the Bureau has been endeavoring to collect data and information on this question which would permit a fair , yet safe , ruling to be made . For this purpose cooperative arrangements were made with three coal companies to visit certain of their mines , making inspections inside the mines to observe the cables and cutting machines in operation . In all , twenty mines were visited . A questionnaire covering the operations of trailing cables was filled out at each of these mines . In a few instances no personal inspection was made , the information being supplied by mine officials after conferences with the Bureau's engineer . At other mines the information given by mine officials was supplemented by personal observation inside the mines , usually at a time when the cutting machines were in operation .

Jul 1, 1923

The extrapolation of results from reconstructed laboratory soil columns to field conditions is difficult because of the limitations of laboratory experiments. Permeability and elution tests performed in the laboratory differed from the natural state in that the soil was sieved through 1/4 inch screen to remove large stones and roots, its density was controlled by tamping the soil into two-inch I.D. tubes instead of normal weathering, and water and latex were applied with a constant head of liquid. Tube wall effects are important in interpreting data. Conversely, interpretation of field results were confounded by non-homogeneities within the sample tested, a soil profile with gradation of permeability and density with depth, and uncontrolled weather conditions and seasonal changes that affected the results. Nevertheless, both laboratory and field tests showed that a specific latex did perform as a soil sealant. In view of these facts a soil box experiment was designed to overcome some of the disadvantages associated with the small laboratory soil columns and the field experiments. Two wood soil boxes 5 ft x 5 ft x 5 ft were built in the greenhouse at the Uniroyal Research Center. They were lined with plastic PVC sheeting provided with tubes every six inches of depth on one side of each box to measure water removal rates under saturated conditions. Tensiometer gauges were placed at depths of 6, 12, 18, 24, 36 and 48 inches and Bouyoucos blocs and resistance thermometers were positioned at 6, 24 and 48 inch depths. Each box was filled with a uniform sub-soil obtained from Ogdensburg, N. J. The texture of this soil was determined to be a sandy loam by the ASTM Hydrometer method, as shown below: [ ] The boxes were thoroughly wetted by sprinkling to abet settling and allowed to dry by draining to check seepage ports and functioning of tensiometers.

Jan 1, 1972

By L. C. IlsLey, E. J. Gleim, F. CRAVEN

Electrical apparatus and circuits began to be used in mines about 50 years ago. A search of the literature on mining reveals that in 1882, umping was being done by electricity in some aines of England. One account tells of a small electric locomotive being used in 1882 "to drive eight corves loaded with coal" in a mine near Dresden. In an account of his visit to some English mines, en American in 1892 mentions that he saw underground electric signals, lights, pumps, hoists, and one revolving- cutter-bar 19wall mining machine,. Among the carl electrical installa- tions in the United States was an electric locomotive in the Lykens Valley Coal Co. mine at Lykens Valley, Pa., in 1887. In 1889 the Sperry electric coal digger was being tried out. Tarce mining machines were placed in the Prospect mine, East Palestine, Ohio, in 1890. An electrical pumping plant was put in oneration during 1892 in the Woodward mine of the Delaware, Lacka- rahma & Western Railroad Co. Thus we Almost coincident with the proposed use of this new servant in under- ground workings, came the thought of making it safe in gassy mines. find an account of a design for a protected stationary electric mine lamp proposed by Edison in 1831. Enclosed-type motors rere developed in the United States and shiped to English collieries about 1903. From those early beginnings there has been continuous progress until to-day one finds hundreds of pieces of specially designed electrical apparatus distributed in American coal mines and in mines of nearly all important coal-producing countries. Along with introduction of this equipment grew the idea of the necessi- ty of government aid, in standardization. In most coal-mining countries to- day the governments either directly or indirectly have a considerable in- fluence in guiding the design of electrical equipment intended for use in Pasay mine

Jan 1, 1933

By G. M. Kintz, E. H. Denny

Although some engineering colleges recognize the importance of instructing young engineers in industrial safety , the different institutions handle this instruction in various ways . It is believed that a recent industrial safety course , conducted at the Colorado School of Mines through the cooperation of this school and the Bureau of Mines , U. S. Department of Commerce , presents some unusual features that are of interest to other schools and to the mining public .

Sep 1, 1930

By Lester G. Morrell

UPTREND in value of mineral production in the Commonwealth of Australia continued in 1963, again pacing the country's general economic growth rate. Increases occurred in output of most raw and processed mineral products, including bauxite, copper, iron ore, pig iron, steel, lead, zinc, cement, gypsum, pyrite, coal, and refined petroleum products. Although the economy of Australia has been traditionally based on wool and agricultural products, in recent years the country has become highly industrialized. Nearly one-third of the 3.6 million total civilian labor force is engaged in manufacturing. Employment in mines and quarries occupies 1.4 percent of the national labor force.

Jan 1, 1964

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By M. E. Tyrrell

Work in this investigation was undertaken by the Bureau of Mines to demonstrate how waste glass might be utilized to lower the required firing temperature and firing time of structural clay products. Mixtures of waste glass and common clays were formed by stiff-mud extrusion and fired to the temperature required to produce a body having 6 to 7 percent absorption. Substitution of glass for one-half of the clay in a red body reduced the firing temperature 500° F, which made possible a 30-percent increase in production; in a tan body, the firing temperature was reduced 400° F, which made possible a 23-percent increase in production.

Jan 1, 1972

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of-combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were conducted in a 1 80 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.13, and 0.06 m/s were determined at 30.60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

By Nicholas G. Theofilos

Ecuador's real gross domestic product (GDP) increased 6% in 1976 despite persistent shortages of electrical power and essential fuels, which caused factory slow-downs and shutdowns. Petroleum export earnings, which made up more than 50% of total export value in 19716, totaled $565 million, a 9% increase over those of 1975. A new 60,000-barrel-per-day oil refinery at Esmeraldas was scheduled to go on- stream in mid- 1 97 7, operating entirely on Ecuadorean crude. Corpración Estatal Petró1era Ecualtoriana (CEPE) started construction of a 600-kilometer network of product pipelines which was scheduled to be completed in 1977 to coincide with the completion of the refinery.

Jan 1, 1980

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By Philip W. Holland

The U.S. Bureau of Mines has designed and built an inexpensive, weatherproof, temperature-controlled cabinet to provide temporary housing for analytical instrumentation. The cabinet consists of an inverted Styrofoam ice chest, an electric fan for air circulation, and a proportional temperature controller equipped with a thermistor sensor and a light bulb as the heater. The cabinet provides a constant-temperature environment for a moisture analyzer and a strip chart recorder when outside temperatures range from -SO to 21° c.

Jan 1, 1993

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By L. C. IlsLey

So many subjects are covered in State mine-safety regulations that any attempt to compare different State laws in their entirety would be futile. On the other hand, if one selects a single phase or branch of safety work, such a comparison may prove profitable. The subject selected for study in this paper is limited to legislation or regulations dealing specifically with safeguarding (electric) motored equipment used in gassy mines. T When one reads glowing accounts of the safety activities being carried on here and there it is easy to believe that everything which is right and proper is being done to safeguard the mine.workers; but, when one takes time to look into the weakness of many State regulations, it is evident that there is still room for improvement. Undoubtedly it would have been much better for the safety of mines if electrical equipment had been introduced into mines 50 years earlier. If electricity had been in general use when the first mine regulations were pre- pared, those formulating the rules would have covered this hazard along with other hazards, but as electricity came in at a later period, safe mine legisla- tion regarding it has been woefully neglected. Today the United States in general is far behind most other coal-producing nations in the provision of adequate safety rules or laws for the installation and maintenance of electrical equipment and wiring. Returning to the subject of our study, approximately 30 of the 48 States mine coal. More than 20 of these States' produce coal in large quantities. How- ever, of the 30 States only four, 3 Pennsylvania, Utah, Washington, and West Virginia, have laws which specially call for the use of explosion-proof types

Jan 1, 1929

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

By Irven A. Jacobson

The thermal reactions of l-methylindole were studied in the temperature range of 525° to 627° C in a flow reactor. The major products consisted of 2-methylindole, 3-methylindole, indole, quinoline, hydrogen, and methane. 2-Methylindole is formed from 1-methylindole by an irreversible isomerization reaction. The 2-methylindole isomerizes in a reversible manner to 3-methyl-indole, the equilibrium favoring the 3-methyl isomer. Indole is formed directly from 1-methylindole. Quinoline is formed from l-methylindole, 2-methylindole, and 3-methylindole.

Jan 1, 1971