Search Documents

By L. A. Readdy

No text. A set of geophysical well logs for U.S. B.M. Pilot Hole "X", Piceance Creek Basin, Colorado.

Jan 1, 1977

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By Lisa Steiner, Robin Burgess-Limerick

Working with or near underground coal mining equipment is hazardous because of the multiple sources of energy and adverse environmental conditions. Of the 4169 injuries reported to Coal Services during the three years to June 2005,447 were associated with continuous miners, 232 with LHD (load-haul- dump) vehicles, 140 with shuttle cars, and 140 with personnel transport - a total of 959, or 23% of all injuries reported during the period. An analysis of the injury narratives accompanying these injury claims highlights a number of opportunities for controlling injury risks. Using the frequency of reported injuries for the prioritisation of risk control strategies has limitations because of the tendency to underestimate the importance of relatively uncommon but potentially high consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggests the following hazards as the highest priority for elimination or control: • handling continuous miner cable • strain while bolting • slipping off continuous miner platform • inadvertent or incorrect operation of bolting controls, and operation of controls while a person is in a position of danger • hitting potholes or other roadway abnormality • collisions while driving underground vehicles

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By Jalna R. Zatko

The Bureau of Mines, U.S. Department of the Interior, has developed a novel method of flocculation dewatering of phosphatic clay wastes using polyethylene oxide as the flocculant. Research was conducted to determine whether ethylene oxide gas was present in the air in the vicinity of disposed waste materials which had been flocculated with polyethylene oxide. Samples of clay waste materials containing polyethylene oxide were prepared in stoppered glass bottles in simulated disposal environments. Gaseous samples, removed over a 75-day period using an airtight syringe, were injected into a gas chromatograph that was capable of separating ethylene oxide from air. The presence of ethylene oxide gas was not detected in any sample. To determine possible degradation products of polyethylene oxide, the properties and reactions of ethylene oxide and its polymers were reviewed. Based upon the literature survey and experimental study, it was concluded that adverse environmental effects were not likely to result from the use of polyethylene oxide for flocculating phosphatic clay waste products.

Jan 1, 1980

By I. A. Jacobson

In a closely controlled laboratory retorting system for oil shale, a relationship was developed by the Bureau of Mines between the temperature in the retort and the weight ratio of ethylene to ethane in the gases produced. Reciprocal temperature was shown to be directly proportional to the log ([ethylene]/[ethane]). From this relationship a number, called retorting index, was developed. The retorting index has the dimension of temperature, but its magnitude depends on both temperature and residence time for the reactants in the heated zone in the oil-shale retort. The slopes of the lines relating reciprocal temperature and the logarithm of the ethylene-ethane ratios are nearly constant for each of the retorting processes for which data have been presented. The retorting index should be a valuable tool to control the operation of oil-shale retorts, either aboveground or in situ. If an optimum operating condition can be established, the maintenance of the optimum or the departure from it should be easily monitored by use of the index.

Jan 1, 1974

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a mini-computer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns an echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display discs, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 10, 1980

By J. P. Conway

The yielding-rock-bolt concept, as developed in South Africa, consists of a smooth-bore die or collar fitted to a standard rock bolt. Laboratory testing at the Bureau of Mines Spokane Mining Research Center under slow and fast strain rates showed that extrusion loads can be controlled by varying the configuration of the die bore and that theoretical analysis (using basically Sachs' theory of wire drawing) predicts extrusion loads of the different die-bore configurations. A derived equation, based on this research, can be used for designed die-thread combinations for any desired extrusion load. Dynamic loading resulted in slightly higher loads (15 percent) than static loading. The strain hardening effect, which increases yield and ultimate strength, was partly offset by adiabatic heating of the threads, which decreases strength.

Jan 1, 1975

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Ernest L. Corp

The natural marine environment can be divided into four basic categories: the air-sea interface, the water zone, the seafloor, and the subbottom. Efforts are being made to accumulate data to delineate the conditions in each of these areas and to conduct engineering studies which will determine how these environmental parameters affect the mining process. Laboratory facilities have been constructed and equipment and techniques for scientific data collection and laboratory research have been developed. Major emphasis is being placed on studying the subbottom material. The objective of this emphasis is to study the engineering properties of marine placer deposits in order to assess their influence on the design and performance of the various mining subsystems involving penetration, excavation, transportation, and disposal. Presented are the results of engineering properties tests on a placer simulant which is currently being used for model and prototype testing of coring tools. The effect of these engineering properties on penetrability, core recovery, and sample recovery is discussed.

Jan 1, 1970

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

[ ]

Jan 1, 2012

By Edward J. Kansa

In a Bureau of Mines study, unsteady, spherically symmetric, one-dimensional, compressible-flow (finite sound speed) equations were solved numerically for a spherical deflagration propagating concentrically in a spherical vessel with Mach numbers ranging from 0.2 to 0.7; trajectory histories agree with the infinite-sound-speed theory developed by Perlee, Fuller, and Saul (PFS). A preliminary result of this study shows that flames propagating with speeds greater than 20 pct the speed of sound in the unburned gas mixture generate a complex history of aerodynamic waves distributed throughout the spherical vessel. Although the average pressure and flame radius agree with those predicted by the PFS models, the aerodynamic waves have a pronounced effect on the flame velocity, differing appreciably from that predicted by the PFS model.

Jan 1, 1976

By John M. Devine

The oxygen bomb-is used extensively for determining sulphur in petroleum, although it has been suspected that the results obtained with this method are somewhat lower than the true varies. In this paper are compared the results given by the oxygen-bomb and Carius methods, the latter being generally accepted as the standard procedure for the determination of sulphur in organic compounds. The Carius determinations given hero were made in connection with a special study of this method.4 Only petroleum oils of the less-volatile type are covered in the present work. Summary and Conclusions. When used with oils containing 2.3 to 0.15 per cent of sulphur the oxygen-bomb method gives results that are consistenly if slightly lower than those obtained with the Carius method. This variation, for the oils used, amounts to 3.1 per cent (on tae basis of sulphur present) for the sample containing 2.47 per cent of sulphur, and gradually increases (as the percentage of sulphur in the oils decreases) to 7.3 per cent for the oil containing 0.15 per cent of sulphur. With the oils studied the presence of ammonium nitrate in the bomb does not influence the results materially.

Jan 1, 1928

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971

By John D. Corrick

A dilute sulfuric-acid leach was developed for extracting lead and copper from lead blast furnace mattes and the chemistry was defined. The possible application of Ferrobacillus ferrooxidans to the problem of salvaging lead and copper from blast furnace mattes was also investigated. Operating conditions were varied to determine their effect on the oxidation and hence extraction of lead and copper from the matte. Conditions varied were temperature, pH, reaction time, aeration in the slurry, and particle size of the matte. A set of optimum conditions were developed that resulted in maximum lead and copper sulfide oxidation. Tests employing these optimum conditions resulted in 82.3 percent of the lead and 98.7 percent of the copper being extracted by a dilute acid leach, while maximum lead and copper extracted using F. ferrooxidans was 69.8 percent of the lead and 78.4 percent of the copper. Tests conducted with a different sample of blast furnace matte indicated that the dilute acid leach might have wide application in extracting lead and copper from other such blast furnace mattes.

Jan 1, 1968

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975