Search Documents

By T. F. Dumm, L. G. Austin

"INTRODUCTIONGomez and Austin (1,2) have recently described calibration procedures for quantitative chemical analysis of particles by energy dispersive spectroscopy using particles mounted and polished in a resin matrix and scanned by an SEM under computer control. Their software is specifically designed for the analysis of Si, Al, Ca, Na, K, Fe and S in coal particles, and in this case the resin is loaded with iodine (3) to enable the exposed cross-section of an embedded coal particle to be differentiated from the matrix. However, the basic ideas of their procedures could be extended to any system of particles where it is desired to measure inorganic species in particles containing light elements such 0, C, H and N which are not directly detected. In these circumstances it is necessary to perform a quantitative determination of the measured components, so that the equivalent volume of light elements in the excited sample volume can be estimated by difference using ZAF and other corrections applied to the raw count intensities.Part of their procedure involves a new technique (2) for estimating background spectrum intensities; the intensity for a particular energy window is then subtracted from the total measured intensity for that window to enable the concentration of the corresponding element to be calculated. In addition, corrections for overlap of peak spectrums are applied. For example, Figure 1 shows some typical spectrums for known materials for the system they used, demonstrating a wide Gaussian spread about the theoretical peak energy. Since background spectrum and peak overlap corrections require a knowledge of the composition of the material, as does the application of the ZAF corrections, it is necessary to have an iterative solution of the equation sets, starting with estimates of the composition based on initial count rate corrected solely for dead time and detector efficiency."

Jan 1, 1989

By R. W. Lewis

The Federal Bureau of Mines Boulder City Metallurgy Research Laboratory conducted experiments in order to develop a spectrochemical method for determining the concentrations of impurities In high-purity tungsten. This report presents a procedure, developed by these experiments, for determining 19 impurities in high-purity tungsten. Metal samples were thermally converted to the oxide, mixed with graphite, which was prepared and mixed with an internal-standard element, and excited in a d.c. arc. Sixteen of the impurity elements were determined with one set of conditions, using germanium as an internal standard. Lanthanum was used as an internal standard in the tests for boron and chromium. Molybdenum required the substitution of sodium chloride for the graphite and the use of copper electrodes. Data on the precision of the method are included in this report. The coefficients of variation vary considerably but average about 15 percent. Higher concentrations of impurities than those investigated may be determined with some modifications of the testing procedure, provided attention is given to the possibility of interelement interferences.

Jan 1, 1961

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data are known. A preliminary objective is to obtain the best values of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964

By William L. Crentz

1. SALES PUBLICATIONS

Nov 1, 1949

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By W. D. Walker

This information circular is offered to the coal-mining industry for use as a guide in selecting, placing, and caring for fire-fighting equipment in coal mines. Its purpose is to suggest minimum requirements for fire protection underground, and it is presented with the hope that it will aid in establishing adequate standards that will provide reasonable protection against underground fires in coal mines. Potentially, a coal mine is a hazardous fire area. Coal itself is a combustible substance, easily ignited. In addition, large quantities of other combustible materials must be present in the area of operations; these include materials for roof support, track ties, doors, ventilation stoppings, lubricants, etc.

Jan 1, 1953

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By Philip C. Good

The Bureau of Mines investigated the feasibility of utilizing low-grade phosphatic shale as a feed for phosphoric acid production. Present practice in the phosphate mining operations of southeastern Idaho is to remove and either stockpile or waste low-grade phosphatic shales as the high-grade phosphate beds are selectively mined. Acid digestion studies were performed on uncalcined shale and on shale calcined to remove free carbon to determine phosphoric acid quality, yield, and amenability to filtration. The untreated shale, containing 21.4 pct P205, was digested with sulfuric acid in a single-tank reactor to yield phosporic acid and gypsum residue. Although 96 pct P205 recovery was attained in digesting uncalcined shale, only the calcined product gave satisfactory filtration rates. Calcined shale yielded phosphoric acid recovery of about 93 pct of the contained P205. It was higher in impurities than commercially prepared acid derived from high-grade western phosphate rock. An acid filtration rate of 745 lb P205/ft2/day was attained. This value is lower than the rate of 900 lb P205/ft that is generally considered to be acceptable in industrial production of phosphoric acid from high-grade phosphate rock.

Jan 1, 1981

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

Roof screening for ground control originated with metal miners in the western United States. At first chain-link fence was used, but because it was so difficult to handle, the miners started installing a more rigid welded wire screen used in the concrete industry. Eventually coal mines in the west began to use screen, and now more and more coal operations, especially longwall mines, are installing roof screen on a regular basis. Screen use has recently increased in the Illinois basin and is now making its way to underground coal mines in the eastern U.S.

By Richard Havens

Samples of low-grade oxide manganese ores were procured from two southern Utah properties by examining engineers of the Bureau of Mines during an investigation of manganese mineral deposits of continental United States. A 2-ton lot of ore was obtained from the Blackbird group of mining claims in Paiute County, 11 miles southeast of Marysvale, Utah. The deposit was described as an intrusive sheet or sill of altered brecciated rhyolite cemented together by manganese oxide minerals. A 2-ton sample from the Black John property, situated 32 miles northeast of Kanab, Kane County, Utah, was taken from open cuts on the vein. The blanket-type vein deposit consisted of nodules and streaks of manganese imbedded in compact gray clay.

Jan 1, 1949

By R. O. Pynnonen

This publication is an analysis of reports to the Bureau of Mines of 44 fatal accidents that occurred during the operation of rubber-tired, front-end loaders in the mineral industry. The causes of the accidents, the nature of the work being performed, and recommendations for preventing similar accidents are included.

Jan 1, 1967

By R. H. Nielsen

A new, cheaper precipitation scheme has been developed to produce purified zirconium oxide, Technical-grade sulfuric acid is used to precipitate a basic zirconium sulfate from a hot dilute hydrochloric acid solution. With close control of temperature, pH, and zirconium - sulfate ratio, excellent purification and complete zirconium recovery can be attained. The process has been successfully applied for 3 months and has proved to be a more satisfactory procedure than the ammonium phthalate process used previously. INTRODUCTION The Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines has developed and improved the Kroll process for the production of pure ductile zirconium and hafnium. metal. Since 1946 over 1 million pounds of zirconium sponge metal has been produced, mostly high-purity material for the Atomic Energy Commission

Jan 1, 1956

By Jack R. Woodyard

Bonding angles, promotion energies, and relative atomic sizes can be estimated through the solution of a set of algebraic equations generated from simple atomic models, and quantum mechanical parameters such as bond strength can be estimated from simple, hydrogenic form-wave functions. The precepts of The Engel-Brewer Theory are melded with the "Crystal Approximation Model" to produce atomic-structure models making these predictions, The two-valence-electron case is presented in this report. For the candidate atoms Be, Mg, Ca, Sr, and Ba the calculated promotion energies agreed within a few percent of their experimental values. These atomic parameters determine the possible crystal structure of the candidate atoms when alloyed. This is part of the effort at the U.S. Bureau of Mines to develop methods for alloy design in response to requirements for new high-performance alloys that conserve critical or rare materials.

Jan 1, 2010

By W. S. Landers

Analysis of the size consist of broken coal has been extended in recent years beyond the mere representation of the relative quantities of the various sizes present in a given lot of the material. Fundamental characteristics of the coal related to the process of breakage fix the distribution of sizes, and it has been found by Rosin and Rammler4/ that a relatively simple law-governs this property. Benhett5/ has described a graphical method of expressing the relationship, and by its use considerable simplification in the expression of size distribution is possible.

Jan 1, 1946

By R. E. Lindstrom

Electrooxidation techniques were investigated on a bench scale by the Bureau of Mines to determine the applicability of the process for extracting molybdenum and rhenium from low-grade molybdenite concentrates. Parameters affecting the extraction, such as pulp density, power consumption, reagent requirements for pH control, and electrolytic cell configuration, were studied. Molybdenum and rhenium extractions of 98 to 99 percent were achieved from several concentrates containing 4.76 to 28.6 percent molybdenum and 180 ppm to 1,000 ppm rhenium. Optimum results were obtained by maintaining pH values between 5.5 and 7.0 during electrolysis and allowing the final pH to rise to about 8.2. Reagent consumption was 4 to 6 pounds of sodium carbonate per pound of molybdenum extracted. The power consumption declined from a range of 12 to 25 kilowatt hours per pound of molybdenum extracted with immersion electrodes to 9.7 kilowatt hours with a bipolar flow-through cell; however, molybdenum extraction was independent of cell configuration.

Jan 1, 1973

By R. M. Santmayers

[This paper presents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining legislation of Bulgaria was prepared from a copy (in French) of the Mining Laws of Bulgaria, promulgated by Royal Decree No. 33 of I. arch. 31, 1910, and published in the "Journal Official," No. 83, April 14, 1910, and checked against a digest prepared by Maynard B. Barnes, First Secretary, American Legation, Sofia, Bulgaria, dated June 10, 1932, which was transmitted through the courtesy of the Department of State. CLASSIFICATION OF MINERAL SUBSTANCES Mineral deposits are classed either as mines or quarries. (Art. l.) Tunes are deposits, the products from which must be processed. Under this class specific mention is made of the metals (gold, silver, copper, lead, zinc, iron, chrome, titanium manganese, tungsten, tin, mercury, platinum, cobalt, nickel, cadmium, aluminum, molybdenum, bismith, uranium, antimony, arsenic), sulphur and other "analogous" mineral substances, phosphate rock, iron pyrites, sulphates, saltpeter, alum, boracic acid and its compounds, talc, asbestos, amber, graphite, merschaum and precious stories of all kinds, reek salt and other salt, peat, coal, petroleum, ozocerite, asphalt and all other bituminous substances. (Art. 2.)]

Jan 1, 1933

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By Michael A. Evanto, George J. Karabin

The Mine Safety and Health Administration, Pittsburgh Safety and Health Technology Center, Roof Control Division, is routinely involved in the evaluation of ground conditions in underground coal mines. Assessing the stability of mined areas and the compatibility of mining plans with existing conditions is essential to ensuring a safe working environment for mine workers at a given site. Since 1985, the Roof Control Division has successfully used the boundary-element method of numerical modeling to aid in the resolution of complex ground control problems. This paper presents an overview of the modeling methodology and details of techniques currently used to generate coal seam, rock mass, and gob backfill input data. A summary of coal and rock properties used in numerous successful evaluations throughout the United States is included, and a set of deterioration indices that can aid in the quantification of in-mine ground conditions and verification of model accuracy is introduced. Finally, a case study is detailed that typifies the complexity of mining situations analyzed and illustrates various techniques that can be used to evaluate prospective design alternatives.

Jan 5, 1999