Search Documents

By John J. Sammarco

Light-emitting diodes (LEDs) are emerging as viable replacements for incandescent (INC)-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. This paper describes the performance of LED and INC sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and air flow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Second, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and INC sources can be magnified toward the end of a 10-h battery discharge cycle. Empirically, we have determined that after 8 h at an ambient temperature of 25 ?C, the average light output of an INC cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery, and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and air flow on the light output of an LED and INC cap lamp were conducted in the National Institute for Occupational Safety and Health Safety Research Coal Mine. The LED cap lamp yielded a vertical average illuminance improve­ment of approximately 9.5%, and the INC cap lamp yielded a vertical average illuminance degradation of approximately 4%. The differences between LED and INC cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38% more efficient than the INC cap lamp with a lead-acid battery at the end of the 10-h driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the INC light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, particularly given that the light output will decrease an additional 30% to 45% over the period of a 10-h shift. The implications of the differences between LED and INC sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and INC cap lamp visual performance research.

Jan 1, 2009

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By D. Harrington

Advocates of health and safety in mining have found themselves confronted in recent years with what might appear to be contradictory procedures with regard to dust occurrence in mines and what appear to be suitable methods or measures to give the mines and mine workers a maximum measure of protection against dust. A concerted and relatively effective drive has been made to introduce rock dust into bituminous and lignitic coal mines to prevent or limit explosion and fire disasters, while an equally determined effort has been and is now being made to curb rock dust or to eliminate it from air in metal mines to prevent or at least limit the occurrence of miners' consumption and other diseases. Both procedures are logical even though the efforts appear to be of an opposing nature. While rock dusting has not been applied in coal mines nearly as universally or as effectively as could and should be done, nevertheless a careful analysis of the record of the past 10 years indicates that the amount of rock dusting that has been done has resulted in the saving of a minimum? of 200 lives annually certainly no small achievement. Largely but by no means wholly due to the use of rock dusting, the number of fatalities from explosions and fires in our coal mines in the last 4 years haw been reduced more than 75 percent as compared with the 4-year period 1911-15, the first years of the existence of the United States Bureau of Mines, which was brought into existence in 1910 largely to try to do something about reducing the disgracefully high fatality occurrence from explosion disasters in our coal mines. Hence, rock dusting has been given at least a. trial and has proved its effectiveness definitely.

Jan 1, 1937

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

By A. Bartkowiak

The lower flammability limit of methane at 0 p.s.i.g. and ambient temperatures is 5.6 volume percent in chlorine, 5.2 in oxygen, and 5.0 in air. The corresponding upper limit values are 70, 60.5, and 15 volume percent, respectively, so that the range of flammable mixtures is greater in chlorine than in oxygen or air. The lower flammability limit of ethane at 0 p.s.i.g. and ambient temperatures is 6.1 volume percent in chlorine, 3.0 in oxygen, and 2.9 in air. The corresponding upper limits are 58, 66, and 12.5 volume percent, respectively. In this instance the range of flammable mixtures is greater in oxygen than in chlorine or air. Generally, the limits of flammability for both methane-chlorine mixtures and ethane-chlorine mixtures widen with increases in temperature and pressure.

Jan 1, 1960

By C. R. Bopp, N. A. C. Smith

"For a period of several years, beginning with 1915, there has been a continuous change in the quality of motor gasoline. The average volatility has decreased, this to the fact that higher boiling fractions of the crude oil have been included in the gasoline. This change in quality was made necessary by the tremendous increase in the demand for motor fuel, caused by the development of the motor car, and during the war was an absolute necessity to avoid gasoline shortages. The Bureau of Mines has kept in close touch with this situation by making surveys from time to time of the gasolines sold throughout the country, as this information is of value to manufacturers and users of motor cars and also indicates when any changes are required in the Government specifications. The Bureau has just completed a gasoline survey and is in a position to make public the fact that there has been very little change in the quality of motor gasoline in recent months.During the period from January 17 to February 3, 1920, 81 samples of actor gasoline were collected by representatives of the Bureau of Mines in seven districts of the United States. The cities selected for this survey were New York, N. Y., including Brooklyn; Washington, D. C.; Pittsburgh, Pa.; Chicago, Ill.; New Orleans, La.; Salt Lake City, Utah; and San Francisco, Cal., including Berkeley. In every case the samples collected were taken in such a manner as to represent material actually being sold as motor fuel, and to include samples from each refinery marketing in the district."

Jan 1, 1920

By L. B. Berger

"INTRODUCTION Accurate determination of carbon monoxide in concentrations ranging from 0.2 to about 0.5 percent by volume is troublesome, because such concentrations are too high for some analytical methods and too low for others. Methods that are sensitive to concentrations of carbon monoxide considerably less than 0.2 percent are approaching their upper limit of usefulness when applied to the analysis of samples containing 0.2 percent or more of carbon monoxide, and it may be necessary to resort to dilution of the sample with a known proportion of air, or otherwise modifying the analytical technique, to obtain satisfactory results. Such methods include the determination of carbon monoxide by reduction of heated iodine pentoxide 3/4/5/ by the ""Pyrotannic acid"" method 6/ and by the so-called ""phosphomolybdic acid"" method. 7/ The use of conventional gas-analysis equipment, such as the Orsat type, in the determination of carbon monoxide in concentrations ranging from 0.2 to 0.5 percent is not desirable, as possible analytical errors may be of about the same magnitude, thus producing results of little quantitative value.For several years prior to this publication, the Gas Analysis Laboratory of the Health Division of the Bureau of Mines has used a modification of the Haldane type 8/9/10/ gas-analysis apparatus for the determination, by absorption in a chemical reagent, of carbon monoxide in low concentrations that are not readily determined by other methods. The method is applicable also to the determination of higher concentrations. As the procedure has proved successful and has been adopted by others, this report was prepared to describe the method and to present results of analyses obtained with it."

Nov 1, 1947

By Michael G. Zabetakis, Aldo L. Furno, George H. Martindill

Hydrazine vapor is flammable in the absence of air at elevated temperatures and atmospheric pressure . The minimum concentrations of benzene , toluene , m- xylene , cumene , and n- heptane needed to inhibit flame propagation through vapor mixtures of hydrazine and hydrocarbon were determined at 125 ° C and atmospheric pressure . These concentrations can be correlated with either the heat of formation or the heat capacity of the hydrocarbon .

Jan 1, 1964

On December 16, the General Services Administration (GSA) suspended weekly sales of surplus silver from the national defense stockpile because Congress approved the Defense Appropriation Act, which contained an amendment to halt silver sales. The amendment, introduced by Senator James A. McClure (R., Idaho), prohibits sales for 6 months while the impact of the sales and alternative methods of disposal are evaluated. The GSA sold 2 million troy ounces since sales started October 14. 46.5 million troy ounces were authorized to be sold during this fiscal year and an additional 58.6 million troy ounces were authorized to be sold over the following two fiscal years. The stockpile held 139.5 million troy ounces of silver when sales began in October. Brush Wellman, Inc., a vertically integrated producer of beryllium products announced plans to modify its Delta, Utah beryllium concentrate processing facility to utilize beryllium concentrates containing as little as 7% beryllium oxide. The company plans to invest $2.5 million for this modification with completion expected in mid-1983. Implementation of this plan to consume lower grade beryllium minerals will significantly increase world reserves of beryllium concentrates.

Jan 1, 1981

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960

By Wing G. Agnew

It is thought that a brief description of the unique mining and milling procedure at the Doyle nine may be interesting to those engaged in small-scale operations at old mines or in working new ore body adjacent to old workings. It also shows what can be done with r. small capital outlay in working a zinc-lead mine on a small scale; as the operation herein described was begun 3 years ago with four men and it now employs 17 men. The original idea was to mine out any ore left around the edges of some old stones above the water level and to rob pillars after an old stope became filled with waste and tailings. This has been done, and the procedure is still being followed; at the same time a paying lead is being mined toward an area in which churn-drill holes have shown ore. Also, preparations are now being made to do some pumping.

Jan 1, 1936

By Robert J. Hundhausen

This paper describes the methods and costs of sinking a 2-compartment shaft at the Hope mine, Clark Fork, Idaho. The Hope mine is owned by the Hope Silver-Lead Mines, Inc. Albert E. Nash, of Clark Fork, is president and manager.

Jan 1, 1948

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By R. V. Lundquist, H. Leitch

Sodium aluminate is the principal aluminum compound formed in the sinters prepared by the lime - soda sinter process for recovering aluminum from silicate source materials . The properties and characteristics of this compound were studied to improve the efficiency of the process . Crystalline sodium aluminate was prepared by sintering stoichiometric quantities of soda ash and calcined alumina for 1 hour at 1,250 ° C. The extent of aluminum extraction from sodium aluminate was determined in water and in solutions of NaOH and Na₂ CO3 . Nearly complete extraction of aluminum from sodium aluminate was achieved only in solutions containing free NaOH in excess of that supplied by the salt through hydrolysis . About 42.2 to 68.8 percent of the aluminum was extracted in water or in solutions of Na₂ CO . The precipitation of alumina trihydrate from sodium aluminate solutions was shown to be part of a continuous , reversible reaction according to the equation Al (OH ) A1 (OH )3 + OHThe reverse reaction dissolves alumina trihydrate in NaOH solutions to produce sodium aluminate . Approximate equilibrium concentrations were determined for the reaction at 30° , 50 ° , and 70 ° C. False apparent equilibrium conditions for the dissolution reaction appear when only a small excess of alumina trihydrate is present in the NaOH solutions . A large excess of alumina trihydrate must be present before the true equilibrium point is assured . The engineering significance of the data is summarized , showing controls that should be exercised for a successful and efficient process .

Jan 1, 1964

By Jonnie M. Estes

A two-constant equation is presented for helium from 30° = T = 1,473° K. This equation is developed by modifying a generalized equation of state originally presented by Redlich and Kwong (20).3 The modification consists of setting B = 0.06372 Tc/PeT. This modified equation represents the compressibility factors of each of 80 isotherms tested in this temperature range to less than 1 percent average deviation.

Jan 1, 1967

By C. N. Rosenecker

The power required to circulate a gas-solids suspension was determined using a centrifugal compressor and a closed system. The suspension consisted of 18- to 40-micron glass beads in a mixture of 89 percent N2 and 11 percent CO2 at 20 psig. Solids-to-gas (S/G) ratios w re O to 2.2 lb/lb; gas flow rates were l.2 to 2.5 lb/min. Power requirement was found to follow the relationship hp t = hp(. + l), where hp t = the total power, and hpg = the power required for pure gas.

Jan 1, 1967

By R. M. Santmyers

Umber and sienna, like ocher, are naturally occurring mineral pig- ments composed largely of clay permeated with hydrated iron (ferric oxide), but they differ from ocher in that they also contain hydrated manganese oxide. The presence of manganese accounts for their browner color. In addition to silica and alumina (clay) and the coloring oxides of iron and manganese, these pigments often contain lime, barium, and other metallic salts as impurities. Sienna most nearly approaches ocher in chemical composition, and the chief distinction is its physical character. It grades into ocher with de- creasing iron content and into umber with increasing manganese content. Sienna is translucent rather than opaque and is more of a stain than a pigment; as the iron oxide content is rather high (often 60 to 80 per cent), the color is strong and rich and varies from pure brown to reddish brown. This pigment raw sienna, terra di Siena, and Italian earth. is known under several names: Burnt sienna is a pigment of an orange-brown tint made by cautionsly calcining raw sienna. It is divided into two grades; American, and Italian burnt sienna. American burnt sienna is a reddish-brown pigment containing from 25 to 60 per cent iron oxide (Fe2O3). One grade, found in Pennsylvania, analyses as high as 80 per cent and is mown as double strength sienna. Italian burnt sienna is a pigment generally containing more iron than the American product, averaging 60 to 75 per cent iron oxide.3 American pig- ments of the same iron content differ materially in shade, having a Havana- brown color, whereas the Italian is more of a maroon. Italian siennas when tinted with 20 per cent of white, show a bluish tint, whereas American siennas yield a brownish or yellowish hue. Raw umber, also known as Turkey umber, Levant umber, and terra ombra, is a greenish to yellowish brown siliceous and ferruginous earth, containing a considerable proportion of one or other of the higher oxides of manganese, Mng04 and MnO2." It is similar in many respects to raw sienna except that it is much coarser and contains more manganese oxide. All umbers contain over 5 per cent of manganese dioxide. Like sienna, umber is a permanent pigment, not being injured by light or by impure atmospheres. Burnt umber (velvet brown, chestnut brown, etc.), results from the calcination of raw umber. The color is much richer and warmer than that of the raw umber. The colors are equally permanent and can be used in conjunc- tion with all other durable pigments.

Sep 1, 1931

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931