Search Documents

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By John Ward Smith

Aragonite, co-occurring with calcite and dolomite as matrix minerals, has been discovered in Mahogany zone oil shales of Colorado's Eocene Green River Formation, posing puzzles on the geochemical patterns of their separate origins, reasons for their simultaneous existence, and their interrelation. The presence of aragonite is demonstrated by X-ray diffraction. Amounts of aragonite and dolomite are significantly and inversely related, but the calcite quantity is essentially independent of either aragonite or dolomite quantity. A geochemical pattern outlining the deposition conditions that created the Green River Formation oil shale is postulated from characteristics of the oil shale. The development of the three separate carbonates--aragonite, calcite, and dolomite--the inverse relationship between aragonite and dolomite, and the independence of amounts of calcite and the other two carbonates are shown to be natural consequences of this oil-shale genesis pattern.

Jan 1, 1973

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By E. E. Harton

Bureau of Mines Information Circular 16, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 as an aid in making estimates of investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included refer¬ences to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Publications in this field have been numerous since compilation of the above bibliography, and the present report was prepared to cover the field from September 1948 through June 1952.3/

Jan 1, 1955

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By Richard G. Stearns

Extensive thick lignite apparently lies within 250 feet of the land surface in Dyer, Lake, Lauderdale, Obion and Tipton counties. Information on geology, land use, soils, groundwater and instability is compiled, along with a bibliography. A test and monitoring site was investigated at Fort Pillow Prison in Lauderdale County. Analyses were made of lignite, overburden, associated water and leachate. Lignite has high BTU (about 7800) and low sulfur (1.1% avg.). A year or more of data are presented on rainfall, water levels, and chemistry of surface water, groundwater, leachate and water from test pits. Main potential environmental problems are quality of surface water, and possibly shallow groundwater. The main aquifer of the region will likely be un-affected by mining. Low transmissibility of shallow aquifers will minimize lowering water levels of wells. Soil reclamation and conservation should be readily accomplished, Dangerous earthquakes have a low probability and mines are not significantly more hazardous than steep bluffs.

Jan 1, 1981

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.

By G. F. Livingston, F. K. Shelton, J. C. Stahl, R. E. Churchward

"INTRODUCTION An investigation of the metallurgy of cobalt from domestic ores has been in progress since February 1940 and has resulted in the formation of a hydrometallurgleal process for the production of electrolytic cobalt metal. Previous reports of these investigations have been given by F. K. Shelton; 7/ and Ruth E. Churchwrd, F. K. Shelton, and G. Knickerbocker. 8/ Briefly, the process, as applied to ores containing cobalt oxide, consists of leaching with H2SO3 or, preferably, with H2SO3 and H2SO4, to dissolve the cobalt. The cobalt solution passes through one or more purification stages to remove iron and elements of the copper group, and cobalt carbonate is precipitated under carefully controlled pH conditions. The cobalt carbonate is dissolved in on acid electrolyte containing sulfuric acid, boric acid, and sodium fluoride. The electrolyte then proceeds to electrolytic cells where cobalt is plated as a metal and sulfuric acid is regenerated.The present paper contains the results of several investigations signed to give a more complete chemical and engineering understanding of different unit processes involved in the electrowinning of colbat. Some work has been done to broaden the process to include arseniferrous cobalt ores as well as the oxide ores upon which the investigation was initiated. Most of the data presented herein have been obtained since the release of the previous reports; any changes suggested heroin that conflict with recommendations in earlier reports are based on more complete data and usually are preferable."

Nov 1, 1945

By S. T. Reese

STATISTICS of injuries in the quarrying and related industries in the United States first became available when the Bureau of Mines collected reports from the operating companies for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1952, is the 33d publication containing statistical data on injuries at quarries and related plants, and it is the first to be published since 1944. The last publication was Bulletin 458, Quarry Accidents in the United States during the Calendar Year 1942. The unpublished statistics for 1942-51 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries at quarries, but there is no Federal law that compels operators to supply such data, and the reports received from operators are voluntary responses to the Bureau's requests for information. Although the figures presented herein may not be complete for the entire industry, every effort has been exerted to make them so, and the figures given are believed to be thoroughly representative of the hazards to which quarry workers are exposed. Moreover, the figures are com¬parable as between States -which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or to comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1955

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980