Search Documents

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By Pete G. Kovalchik, Lynn A. Alcorn, Rudy J. Matetic, Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage is comprised of seven different types of machines. The continuous mining machine is first among all the equipment with 35% of the noise overexposures. The ational Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce excessive exposure for operators of continuous mining machines and preventing additional cases of oise Induced Hearing Loss (NIHL) by developing low-cost retrofit noise controls for mining equipment. This paper describes a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 26.4% and 27.4% noise exposure reduction for the continuous mining machine operator. This research is providing the mining community with an additional noise control to be utilized on continuous mining machines, therefore reducing operator noise overexposure. Utilizing this newly developed noise control, along with previously proven controls for the continuous mining machine chain conveyor, will provide operators of these machines an opportunity to be within the MS HA-Permissible Exposure Limit (MSHA-PEL).

By Raymond P. Maloney

The Bureau of Mines investigated the White Mountain mercury deposit, in the Kuskokwim River Basin, to better determine the extent of mercury mineralization and to encourage its development by private industry. A program of diamond drilling, augering, bulldozer trenching, and sampling was carried on during four field seasons, from 1960 to 1963, inclusive. Significant amounts of cinnabar, with only trace amounts of arsenic and antimony, occur in dolomite over an area about 4,000 feet long and 1,500 feet wide. The deposit differs from other mercury deposits in the Kuskokwim River Basin by the absence of silica-carbonate and rhyolite intrusives. Small-scale mining was started in 1963 as the result of Bureau investigation and continued during the summers of 1964 and 1965. The investigations indicate that open pit mining might be the most feasible method of working this deposit.

Jan 1, 1967

By M. Howard Berliner

The Harding pegmatite dike is well known for the production of spodumene and lepidolite in the period 1920 to 1930. It attained greater prominence during the last war by being the largest producer of domestic tantalum ore from the rare mineral microlite. The deposit is believed to be the only proved reserve of tantalum ore in the United States today. In 1943 the main portion of a large tantalum-bearing zone in the Harding dike was developed by the Bureau of Mines with the assistance of the Federal Geological Survey. Analysis of this zone from 39 diamond drill holes and quarry exposures showed a large deposit containing 2 pounds of microlite per ton and 21 percent spodumene, In September 1948, the Bureau of Mines resumed development of the deposit with a view to extending the tantalum-bearing zone farther to the southwest or delimiting the ore body. Seven diamond-drill holes failed to penetrate the ore zone in its southwestward projection, Much of the following general information is summarized from the report on the first exploratory work of the Bureau of Mines by John H. Soule.2/

Jan 1, 1949

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973

By Robert L. Jones, Clifford Dunham

"INTRODUCTION The Wah Wah mine was examined 3/ by the Bureau of Mines in September, and a project was started in November 1942. Assistance was given by the Federal Geological Survey in formulating proposals and plans, and two geoloists were assigned to map the surface and underground workings in October 1942.HISTORYThe Pine Grove mining district was organized in 1S73, but no work was done there until it was reorganized in 1879, after which it is reported that a little ore was shipped. The Wah Wah Mining Co. was incorporated September 2, 1937. Prior to that time, predecessor organizations had spent approximately $122,000 on the property now held by this company. The board of directors of the Wah Wah Mining Co. approved expenditure of $47,652.14 from September 1937 to June 1942 for development. This work was confined to the Tasso shaft and connecting levels. Shipments in 1939 amounted to 925.789 dry tons with a gross value of $12,477.83. This ore contained 20,130 pounds lead, 1,390 pounds copper, 7,434 ounces silver, and 65.09 ounces gold. The mine was idle from July 1941 to November 1942, when, the Bureau initiated a project to unwater the Tasso shaft and proceed with the exploratory work as outlined in the War Minerals Report."

Apr 1, 1946

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 224 natural as samples from 18 States. Of the total, 191 sam¬ples were collected during calendar year 1981. The remaining 33 samples were collected during previous years, but releases, granting permission to publish were not received until 1981. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and special helium apparatus described previously (1-2).3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-five publications have presented the results of 12,827 gas analyses made prior to 1981. The first three bulletins (1-3) contain analyses and related data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24) containing 7,609 analyses of samples collected since 1960.

Jan 1, 1982

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has nude necessary a general survey of coking-coal reserves in the United States. These investigations were begun in 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one of a series, by counties, describes the preparation characteristics of the coals of Letcher County, Icy. From these data it is possible to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable under present standards for producing metallurgical coke, (b) which coals require special and more intensive treatment in preparation than is now practiced, and, (c) which coals cannot be upgraded by known commercial preparation methods to metallurgical fuel standards now accepted.

Jan 1, 1955

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

By J. Grumer

The Bureau of Mines, under the sponsorship of the Space Nuclear Propulsion Office, conducted a laboratory-scale hydrogen safety study which determined several combustion characteristics of hydrogen diffusion flames. Experiments show that ambient air may enter the top of a hydrogen flare stack when the hydrogen flow is low. A new concept, supported by photographic evidence, predicts that diffusion flames burning in air on a wide, upright pipe (stack) and fed with slow, upward flows of buoyant gas will induce a downward flow of air along the walls of the pipe that can support combustion within the pipe. Predicted flamedip limits agree roughly with experimental values determined on 6-, 12-, and 18-inch-diameter stacks and increase with increasing stack diameter. Measurements were made of the limiting flow at which a hydrogen diffusion flame blows out in still air. By means of an empirical application of the critical boundary 8 velocity gradient concept, these data lead to a blowout limit of about 10 reciprocal seconds for a hydrogen diffusion flame. Burning rates of large hydrogen diffusion flames ranging from about 0.03 to 1 ft/sec were used to predict approximate flame heights on flare stacks. Temperatures of larger hydrogen diffusion flames up to about 3,600° F were observed, but the most representative value appears to be about 2,600° F. It was found that crosswinds do not strip significant amounts of unburned hydrogen from its diffusion flame and that water-cooled flare stacks are not likely to be damaged when flame is blown back into them by opposing winds.

Jan 1, 1970

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By H. P. Greenwald

"INTRODUCTION In the course of its studies of the explosibility of various coal dusts in the Experimental coal mine, the Bureau of Mines has tested coals representing the entire range of volatile content found in the United States. In connection with their work the Bureau's field engineers some¬times meet operating officials who are not impressed by the fact that there is an explosion hazard in mines working low—volatile coals. Actually the difference in explosion hazard between high—volatile and low—volatile coals is one of degree and not of kind. The purpose of this paper is to set forth briefly the experimental evidence that has been accumulated on the explosibility of coal dusts containing 8 to 31 percent volatile matter on a dry, mineral—matter—free basis.There have been numerous dust explosions in mines in which coals were worked that have compositions within this range. Those explosions are listed in an appendix, together with a bibliography of Bureau of Mines papers describing explosion tests in the Experimental coal mine."

Jan 1, 1940

By Stephen D. Cramer

A nondestructive procedure for measuring electrodeposit porosity has been developed which records the location and number of deposit defects including pores, pits, and voids. The procedure involves the passage of an X-ray beam through the deposit-substrate system onto suitable film. The defects are recorded as images on the film. Variables studied included intensity and spectra of the X-ray beam, composition and thickness of deposit and substrate, film type and developing procedure, and limits for detecting defects. At an X-ray tube voltage of 40 kv, pores several mils thick were easily detected in copper-nickel specimens more than 20 mils thick. To illustrate the utility of the procedure, the effect of substrate oxidation and of current density on electrodeposit porosity was briefly studied.

Jan 1, 1970

By J. W. Paul

This report is one of a series of papers on coal mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of bringing to the industry a knowledge of methods as they are used at the present time, and data on certain features which govern costs, safety, and conservation. The methods employed are, influenced by local conditions with respect to the character and dip of the coal, the nature of the, roof and the thickness of the overburden, and the means employed for roof support and its control.

Jan 1, 1929

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,954 samples, representing the products of 93 companies. The samples were collected during December 1955, January and February 1956. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1956

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By P. D. Lindahl

[A cost/benefit analysis was conducted by comparing the industry cost to protective structures on low-coal face equipment with the benefits paid for injuries/fatalities considered preventable by the use of these structures. Th industry costs were based on estimates by OEM's and rebuild shops for install protective structures on new and rebuilt face equipment. The accident benefit was based on evaluations performed by the USBM Accident Cost Indicator Model. Industry wide population data were developed on low-coal face equipment and injuries/ fatalities preventable with protective structures. The results of the analysis are to be used as a tool by USBM in determining the feasibility of continuing development of cab and canopy technology for low-coal equipment.]

Jan 1, 1983

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974