Search Documents

Objective: To identify and evaluate a permanent stopping to direct ventilation airflows in large-opening metal/nonmetal mines.

May 1, 2006

By William D. Riley

In order to evaluate the corrosion resistance of zirconium in mineral extraction processes, such as a clay-hydrochloric acid leaching process for extracting alumina, the Bureau of Mines conducted corrosion studies in HCl-AlC13-FeC13 environments. A series of weight loss and electrochemical tests were conducted at 25° and 65° C in aluminum chloride (AlC13) plus hydrochloric acid (HCl) solutions containing 0 to 1,000 ppm ferric ion. It was determined that zirconium, which normally exists in a passive state in chloride-containing solutions, undergoes pitting attack in solutions containing more than 100 ppm of ferric ion. It is also shown that an oxide film prepared in air at high temperature offers protection in acid solutions containing levels of ferric ion from 300 to 1,000 ppm.

Jan 1, 1981

By C. E. Reistle

The generation of steam for drilling operations has visually been accomplished in the past by the use of portable locomotive-type boilers without the aid of auxiliary equipment or advanced for economizing fuel or water consumption. This has been due primarily to the fact that the steam-generating plant of a drilling well must necessarily be of temporary and portable design, and the amount of steam generated has not been considered sufficient to justify the additional expense necessary to obtain more economical operation. However, with the constantly increasing depth to which oil wells are being drilled and the use of larger and heavier equipment, the steam requirements have reached a point where equipment and methods that were previously considered as applicable only to permanent plant installation can be and are being used to a decided advantage by the more progressive operators. As an example of the present-day requirements and the rapidly increasing steam consumption in rotary drilling, a comparison between the requirements during the intensive drilling period in the Seminole end Oklahoma City fields of Oklahoma is of interest. In the Seminole field. There the approximate depth of rotary drilling was 3,500 feet, the general practice was to use three 85 to 90 or 100 horsepower A. P. I. code boilers operating at a working pressure of 175 to 200 pounds per square inch. The fuel end water consumption was approximately 450 to 500 thousand cubic feet of gas and 700 to 750 barrels of water per day. In the Oklahoma City field, where the average drilling depth is approximately 6,500 feet, the general practice is to use either four 100 or 116 horsepower or three 123 horsepower A.P.I. code boilers, operating at a pressure of 250 pounds per square inch. The fuel and water consumption varies from 550 to 750 thousand cubic feet of gas and from 1,000 to 1,500 barrels of water per day.

Jan 1, 1930

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By R. P. Maloney

The Bureau of Mines conducted a reconnaissance of the less accessible parts of the Beluga River coalfield in August 1957 to determine, if possible, which areas were most favorable for developing large reserves of coal suitable for open-pit mining. Several outcrops of subbituminous coal were observed within an area about 30 miles long and 3 miles wide; neither the length nor the width of the coal-bearing area was delineated by the examination. Coal beds 30 feet thick or more outcrop at two places, and beds 5 to 20 feet thick or more outcrop fairly abundantly along the Beluga River and its tributaries The coal measures appear to occur in a series of folds. The overburden comprises glacial gravels and poorly cemented sandstones and ranges from 20 to 400 feet in depth. Few partings were seen in any of the coal beds. Samples ranged in calorific value from 6,240 to 8,246 B. t. u. on an as-received basis. Adequate water is available for stripping by hydraulic methods.

Jan 1, 1958

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959

By P. R. Tisot

Knowledge acquired from this research contributes to a better understanding of the physical structure of Green River oil shale and provides fundamental data and concepts that may serve to improve oil-shale technology. This study by the Bureau of Mines indicates that oil shale is a highly consolidated organic-inorganic system with no significant micropore structure, pore volume, or internal surface. This system is a form of physical structure that precludes rapid diffusion of either gases or liquids. The mineral matter consists essentially of nonspherical particles that tend to follow a log-normal size distribution. An excess of 99 weight-percent of these particles have equivalent spherical diameters of less than 44 microns--75 weight-percent are from 2 to 20 microns, and 15 weight-percent are less than 2 microns. The surface area (3 to 5 square meters per gram) of these mineral constituents is mainly external surface. The mineral constituents contain some micropore structure--pore radii ranging from 10 to 100 Angstrom--with the pore sizes randomly distributed. Distribution of the organic matter within the inorganic matrix is essentially interparticle and not intraparticle. The organic matter within the micropores of the mineral constituents is less than 4 percent of the total. Estimates made from surface area data suggest that perhaps only a small amount of the organic matter is bonded either physically or chemically to the mineral constituents.

Jan 1, 1963

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By H. Dale Nichols

[The growing importance of the Sundence (Jurassic) formation an a source of oil, in the Rocky Mountain area has prompted the making of a series of porosity determinations of core samples collected. from the reservoir sands of the Lance Creek oil field, Niobrara. County, Wyo. These analyses are preliminary to a stud of fluid and energy relations in the Basal Sundance reservoir of that field, and the determinations of porosity will be used in subsequent studies requiring, calculations of the volumetric capacity of the reservoir and estimation of the reserves of oil and gas. However, the porosity characteristics an of the Sundance sands in the Lance Creek field are factory that affect the solution of many current practical problems of development and operation. Primarily for that reason but also because it is recognized that porosity values of different oil-production sands are of widespread interest throughout the industry, the results of the initial work have been presented in tabular and graphic form with no attempt to evaluate their significance as they relate to the production history of the field.]

Jan 1, 1938

By J. E. Pahlman

As part of its effort to reduce the need for strategic minerals through conservation and to reduce the capital and energy requirements of mineral processing, the Bureau of Mines has investigated a method for preparing ferrochromium alloys containing less than 2 percent carbon. This method will conserve chromium and should reduce the capital and energy requirements for chromite reduction. Reduced products containing less than 2 wt-pct C and as low as 0.01 wt-pct C were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 torr and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be supe¬rior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates (Fe,Cr)7C3 and (Fe,Cr)23C6, No evidence of carbide intermediates Fe3C or Cr3C2 was found. Buttons of ferrochrome alloys were made by melting a mixture of reduced products with CaO and Si02 at 1,700° C for 20 minutes in an induction furnace,

Jan 1, 1980

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By D. J. Stoops

The object of the research described in this paper was to investigate the effect of metallurgical and surface treatments on the corrosion behavior of arc-melted reactor-grade zirconium in cupric or ferric chloride solutions. An apparatus was constructed and specimens of various metallurgical conditions and surface treatments were tested for 6 days at 35° C., with aeration. Some correlations were observed between corrosion rate and the metal's condition and treatment, Specifically, the unattacked or least attacked specimens were those that had been etched as a final treatment before testing. The most severely attacked specimens were those that had been vacuum-annealed as a final treatment before testing. The moderately attacked specimens were those neither vacuum-annealed nor etched, but having a final surface treatment which left a cold-worked surface. Attack by cupric and ferric chloride was by pit- ting with no preference for grain boundaries, The corrosion scale was cow posed predominately of very fine zirconim particles, Particles from the FeC1,-corroded specimens were more pyrophoric than those from CuCl2-corroded specimens, and appeared to have a higher surface area to volume ratio. Comparison of results to those of previous investigators showed that at certain salt concentrations the more pure, reactor-grade zirconium was quite resistant to attack while the less pure, graphite-melted zirconium was severely attacked.

Jan 1, 1962

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"K. A. DIGREGORIO, E. v. CILENTO, AND R. c. LANTZ. Measurement of superoxide release from single pulmonary alueolar macrophages. Am. J . Physiol. 252 (Cell Physiol. 21 ): C677-C683, 1987.-An electrooptical method was developed to quantify superoxide (02) release from single rat pulmonary alveolar macrophages (PAM) during adherence to the bottom of a culture dish. This was done by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate at 550 nm from videorecorded images of individual cells. Temporal changes in cell optical density, which are proportional to the mass of diformazan produced, were calculated from videophotometric measurements of the change in light intensity over individual cells. Total diformazan produced increased 78 and 1263 with an increase in NBT from 0.5 to 1.0 and 2.0 mg/ml, respectively. Total diformazan produced and maximum rate of production among individual PAM varied two- to threefold providing strong evidence for heterogeneity in 02 production. Specific inhibition of 02 production by superoxide dismutase, iodoacetate, and chlorpromazine significantly reduced the total diformazan produced and maximum rate of diformazan production. Hydrogen peroxide was not involved in NBT reduction, since catalase alone did not significantly change diformazan production. This novel method to quantify 02 release from single PAM should be valuable in analyzing heterogeneity and single cell kinetics of O; production, in assessing the effects of exposure of cells to particulates on O; release, and in relating release to electrophysiological measurements.rat; nitro blue tetrazolium; macrophage heterogeneity; single cell kinetic PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria (24). This process involves ingestion as well as destruction of foreign matter. Phagocytosis is usually accompanied by a respiratory burst that increases cellular oxygen consumption and glucose metabolism in the hexose monophosphate shunt (7), which leads to the release of highly reactive oxygen metabolites at the surface of the · plasma membrane (6, 27). These agents have been implicated in the killing of bacteria by phagocytes (22), but have also been shown to be toxic and have been linked to cancer, emphysema, arthritis, diabetes, and other diseases (17, 22, 30). Toxic effects may be a result of either an abnormally low production of metabolites, resulting in damage to lung tissue by respirable bacteria and dusts, or an abnormally high production, resulting in direct damage to lung tissue by metabolites themselves."

Jan 1, 1989