Search Documents

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

"Human accidents are caused by production accidents, generally ones (such as derailment of cars, falling rock, etc.) that have occurred numerous times before an employee was actually involved. Prevention of human accidents is, one of the essentials in cutting operation costs, and advocates of safety are studying economics to assist them in their work of preventing accidents.Workman's compensation insurance or compensation for human accidents is a true operating cost, and is the only purely tangible measure available which gives a measurement of the cost of accidents even though, as will be pointed out later, it represents but a portion of the total cost of human accidents.In using premiums paid for compensation insurance as a measure of the cost of accidents, it must be kept in mind that most insurance laws, as pointed out in a former paper (Serial 2590 of the Bureau of Mines) provide a waiting period before compensation for the lost-time wages starts, with the compensation limited to definite percentages of the wages. The waiting period and limited compensation combined tend to limit the amount paid to an injured workman who, if he receives 1/3 of the lost-time wage, will probably have been reimbursed as high as the average injured workman.The total or complete economic cost of human accidents, must include, in addition to compensation paid for lost time, and the portion of the lost-time wage suffered by the workman for which he is not compensated, the additional cost to the company through-(a) temporary decreased production by the breaking down of the morale, etc., (b) the breaking in of a new employee which is admittedly expensive,(c) the increased liability of human and production accidents caused to or by the new employee.Another charge against accidents, which is not included in the compensation payment, is the economic loss through the killing of as workman who has no dependents. Few of the States' laws require any compensation except burial expenses to be paid for fatalities to persons having no dependents. It is estimated by the United States Bureau of Labor Statistics that the economic loss through a fatality is 6000 shifts. If each fatality was compensated for this amount of time and at half-time wages, using an average wage of $5.00 per shift, the compensation for fatality based on the economic loss would be $15,000. but the average actual compensation paid for each fatality is about $3,000."

Jul 1, 1924

By W. J. Long

As a part of the strategic mineral exploration program, examining engineers of the Bureau of Mines collected samples of ore from four manganese properties in Yavapai, Yuma, Maricopa, and Mohave Counties, Ariz. As all of the ores were too low in grade to be acceptable by manufacturers of ferromanganese beneficiation studies were made to determine the amenability of the ores to concentration.

Jan 1, 1948

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By William C. Cooley

[ ]

Jan 1, 1975

By R. A. Friedel

THE IMPORTANCE of infrared and ultraviolet-visible spectrometry in studies of the structure of coal and similar substances is described. Special experimental techniques have been developed for these studies. Thin sections of coal are preferred, but halide pellets are easier to prepare. Information obtained from infrared spectra on chemical functional groups has been discussed; the importance of both intensities and wavelengths of absorption bands has been emphasized. Functional groups assigned include aliphatic and aromatic CH, methylene and methyl groups, hydrogen-bonded hydroxyls, hydrogen-bonded and chelated carbonyls, phenolic structures, minerals, and aromatic structures that are benzenoid or polynuclear. Infrared studies of structures of coal extracts, distillates, and reaction products of various processes, both chemical and physical, are discussed. Coallike infrared spectra of chars of model compounds have been utilized extensively in studies of coal structure. Ultraviolet-visible absorption spectra of coals show a lack of fine structure and low spectral intensities. These results have been applied to the questions of the chemical and physical structure of coal, particularly the question of polynuclear aromaticity of coals. The color of coal is also treated. The physical-chemical origin of the color of coal may be due to free radicals, as interesting correlations of ultraviolet-visible spectra with electron paramagnetic resonance have been obtained. The optical color of coal has been explained and simulation of the color changes observed in thin sections has been carried out, The spectra and structure of coal derivatives and other carbonaceous materials are also discussed. Possible sources of error in absorption spectral measurements are pointed out. Limited measurements of the ultraviolet-visible reflectance spectra of coal are described.

Jan 1, 1967

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By A. C. Fieldner

In the course of its investigations on the properties of coal and in rendering fuel-inspection service to other agencies of the Government, the Bureau of Mines has accumulated a comprehensive file of coal analyses that includes data on virtually every coal field of commercial importance in the United States. As knowledge of the composition of coal is potentially valuable to every user of coal, the Bureau publishes its analytical records. Before 1921 such publications contained analyses of coal from all parts of the United States; individual analyses or average analyses of a series of shipments of coal were given with the name and location of the mine producing the coal. Beginning in 1921 the analyses were published by separate States because the quantity of data had become so great. The separate papers published to date, with Bureau of Mines Technical Paper numbers, are as follows: Alabama, 347; Arkansas, 416; Colorado, 574; Illinois, 634 and 641; Indiana, 417; Iowa, 269; Kansas, 455; Kentucky, 30S; Maryland, 465; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344; Oklahoma, 411 ; Pennsylvania (bituminous), 590; Tennessee, 356; Utah, 345; Virginia, 365; Washington, 491 and 618 (618, published in 1941, supplements 491); West Virginia, 405 and 626; and Wyoming, 484. From time to time the various papers will be revised to include later analyses and other data. The Bureau of Mines annually receives many inquiries as to the composition of coals obtained from specific localities or, conversely, as to the localities from which a given kind of coal may be obtained. This paper presents a summary, in tabular form, of the composition of commercial coal resources of the country. Specimen analyses are given exemplifying the analysis of coal mined in each coal-producing county, or, where it was feasible, coal from each bed in each county; also, ranges of analyses, within which the composition of most of the coal represented will fall, are given where there were enough analyses to permit satisfactory determination of the ranges. In addition, the degree of metamorphism from lignite toward anthracite of much of the coal is indicated by the classification by rank. This classification reveals to more experienced users of coal some of the general properties of coal, that is, whether the flame will be long or short, whether the coal will cake in the fire, and how it is likely to behave on exposure and in storage.

Jan 1, 1942

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By S. A. N. Sheya

The U.S. Bureau of Mines performed batch equilibrium contact experiments to examine the ability of activated coconut-shell carbon to adsorb various metal cyanide complexes. Tests were also conducted to determine the effect these cyanide complex impurities might have on the adsorption of gold by the activated carbon. Metal cyanide species included in the investigation were antimony, arsenic, cadmium, calcium, cobalt, gold, iron, mercury, nickel, silver, thallium, and zinc. Tests were made over a pH range of 6.4 to 12.5. The carbon exhibited a preference for gold adsorption over other metals present in solution. In the absence of gold, the metal cyanide complexes were adsorbed; adsorption generally decreased with increasing pH. However, calcium and thallium adsorptions increased with increasing pH, while arsenic and iron were not adsorbed at any pH.

Jan 1, 1989

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By Gerald W. Elger

This report describes development of the fusion-leach crystallization precipitation process for producing a hafnium content feed material for hafnium-zirconium separation plants. Mixtures of zircon, potassium silicofluoride, and potassium carbonate (or potassium chloride) were fused to prepare soluble potassium zirconium hexafluoride-potassium hafnium hexafluoride salts. High extraction of these salts was obtained by countercurrent leaching the fused material in dilute hydrofluoric acid. About one-half of the hafnium was recovered in hafnium-enriched mother liquor by cooling clarified lead: liquor to crystallize most of the zirconium salt. Additional hafnium was recovered from the primary crystals in a multiple dissolution-recrystallization step. Hafnium-enriched oxides having a hafnium-zirconium ratio of more than three times that of zircon were precipitated from the combined mother liquors. The hafnium and zirconium recoveries in the precipitate were 83 and 24 percent, respectively. About 71 percent of the zirconium and the remainder of the hafnium were recovered in potassium zirconium hexafluoride crystals of low-hafnium content.

Jan 1, 1966

By B. P. Martinez

A process for regenerating spent pickle liquor is proposed in which some of the water is evaporated at atmospheric pressure and ferrous sulfate is precipitated as monohydrate crystals..Equilibrium conditions are set for a slurry of crystals in a mother liquor containing 5 percent FeS04 and 45 percent E2S04, by weight, and boiling at about 235° F. The slurry is pumped continuously to a filter, and the mother liquor from the filter is pumped back for reuse in the pickling tanks. The net result of the process is to remove ferrous sulfate in the regeneration plant at the same rate ac it is produced in the pickling tanks. This process is integrated with the steel-pickling operation and controlled by the pickling requirements for particular steels. Spent pickle liquor is removed for regeneration continuously from both batch and continuous picklers at higher acid concentrations than would be dumped to waste because no acid is neutralized or discarded. However, the process is not designed to keep a sulfuric acid concentration stronger than 25 percent in any pickling tank. To retain flexibility in the pickling operation, all acid makeup is added to the pickling tanks. Rinse waters are used as water makeup for the pickling tanks. To further minimize waste of acid in the rinse waters, improvements of rinsing practices are outlined.

Jan 1, 1953

By D. E. Shanks

This U.S. Bureau of Mines (USBM) research simplified an earlier hydrogen chloride (HCI) leach-sparge process developed by the USBM to recover reduction-grade alumina from domestic kaolin clay. Improvements were made by decreasing the initial leaching acid concentration from 25 to 20 pet, decreasing the leaching time from 1 to 2 h to 15 to 30 min, eliminating the solvent extraction step for Fe removal, and eliminating the step to recover the AI content of the bleedstream circuit. A 10-cycle bench-scale experiment of the simplified process showed that the ferric chloride (FeC13) concentration built up to 9.3 g/L in the recycle stream. This did not interfere with any of the unit operations or final alumina product purity because Fe forms stable soluble chloride complexes when sparged with HCI and is easily washed from the large aluminum chloride hexahydrate (ACH) crystals. The reduced leaching time and acid concentration did not decrease Al extraction.

Jan 1, 2010

By C. W. Owings, L. D. Tracy

"IntroductionMany bituminous coal-mining companies have inaugurated extensive safety Programs, but the failure to have approved or permissible equipment or safe practice in only one part of a mine has resulted in disaster. The necessity of using only equipment bearing the U. S. Bureau of Mines approval plate is emphasized by the fact that many accidents are the direct result of carelessness on the part of trusted employees using non-permissible equipment. A concrete example is found in the case of an explosion on October 26, 1926, in a mine in the Pittsburgh district, Pennsylvania.Story of the ExplosionAt about 10 o'clock on the night of the explosion an examination was made in No 2 butt left and parallel off 7o. 14 north, and was found to be clear of dangerous accumulations of gas. (See figure). Several hours later a crew of two men brought a self-propelling rock-dusting machine within 50 feet of the face of Po. 2 butt parallel before they examined for gas. The machine operator found an accumulation of explosive gas about 18 inches from the roof. He began to wave his arms thoroughly mixing the gas and air. Undoubtedly a highly explosive mixture was created, and as the men attempted to run the machine back to fresh air an explosion occurred.The helper dropped to the floor and was burned about the face and wrists. The machine operator ran down the entry and was more severely burned about the face, neck, and arms. He later developed pneumonia and died. Both men reached the door in the chute between No. 14 and No. 15 north. A pumper, who had felt the rush of air, found the men and helped them to walk outside."

May 1, 1927