Search Documents

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 years, until in 1936 probably more than 80,000 such units were put into use, According to reports of the Bureau of the Census 75,543 residential stokers mere sold in the first 10 months of 1937 by 108 manufacturers. This rapid expansion has made itself felt in the coal-mining, industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912 in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of tie present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

By H. B. Brunot, Ilsley. L. C., E. J. Gleim

"INTRODUCTION One of the various phases of the work by the U.S. Bureau of Mines, in its endeavors to minimize the hazards that attend coal mining, is the investigation of electrical motor-driven machinery. The object of this investigation is to foster the development of explosion-proof machines for use in gassy mines. This investigation is conducted under the provisions of Schedule 2C, which prescribes the inspection and tests made upon motors, controllers, and other electrical parts to determine their ability to withstand internal explosion without discharge of any flames. The method of conducting these inspections and tests is described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine-Type Electrical Equipment for Permissibility, published in 1929. Formal approval of a machine for use in gassy mines is not granted by the Bureau of Mines until the machine is found to comply with the requirements, including inspection and test. When it is approved it is entitled to classification as a ""permissible"" machine.The high regard in which machines approved by the U.S. Bureau of Mines are held by engineers of other countries is attested by the growing number of shipments of permissible equipment; to other nations, including Australia, Russia, Norway, Japan, and Manchuria."

Aug 1, 1936

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By Shiro Watanabe

To determine the potentialities of nickel as a substitute for cobalt in catalysts for the synthesis of hydrocarbons from carbon monoxide and hydrogen, RESULTS The maximum oil yields obtained in bench-scale equipment were as follows: Using 100N1:20Mn:100 kaolin:200 diatomaceous earth catalyst, a maximum yield of 133.8 cm.3/m.3 of pure CO+2H2 was obtained from one pass of the feed gas, With a nickel:cobalt mixed catalyst (Ni:Co - 3:7) having the composition 100(Ni+Co):8MgO: 5Th02:200 diatomaceous earth, a maximum of 172.2 cm.3/m.3 of pure C0+2H2 was obtained.

Jan 1, 1951

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By Henry Kreisinger, WALTER T. RAY

This bulletin contains a statement of certain results that will be embodied in a report describing investigations of the combustion of fuel made by the United States Geological Survey and the Bureau of Mines in a specially constructed long furnace. The furnace forms part of the fuel-testing plant at Pittsburg, Pa., which was established and equipped by t.he Geological Survey, but passed under the control of the Bureau of Mines on July 1, 1910, when a t.ransfer of fuel-test.ing investjgations, authorized by act of Congress, became effective. The work discussed in this bulletin was done under the direction of the Geological Survey. The furnace was designed and built for an experimental study of the processes of combustiop, this study being part of a comprehensive plan for testing fuels to determine their heat value and the manner in which they can be used to best advantage. Although the main object of the researches made with the furnace by the Geological Survey was to examine critically the production of sensible heat by combustion along the path of the gases rising from the fuel, an interesting as well as important side problem developed in the study of the simultaneous dissipation of the heat through the walls and roof . of the furnace. Thus incidental data were collected on the temperature gradient through the walls at several places. These temperature data. (together with the heat conductivity of the material of the walls) formed the basis for calculating the heat dissipated through the walls. The object of this report is to present and discuss these temperature data. The discussion particularly concerns the air-space type of wall construction as compared with the solid brick wall or walls type, in which the air space is filled with some solid material of low heat conductivity. The conclusion of the authors, which perhaps will surprise some readers, is that, so far as loss of heat is concerned, a solid wall of brick or any ordinary material is preferable to a hollow wall of the same total thickness, especially if the air space in the hollow wall is near the furnace side. There is a general belief that l?ince air is a poor conductor of heat, air spaces built into the walls of a furnace will prevent or reduce heat dissipation through the wa.lls. Although there may be instances of furnace walls in which such construction reduces the rate of heat flow through them, yet as a rule the effect of the air space is just the opposite. While the heat does travel very slowly through the air by conduction, it leaps over the air space readily by radiation. Although this latter mode of heat propagation is common in nature, the laws governing it are not generall;y known and are seldom taken into consideration when furnace walls are being designed. It may be stated here that the quantity of heat passing through a. portion of a solid wall by conduction depends on the difference between the temperatures of the two planes limiting the portion of the wall. The quantity of heat that passes across the air space in the waH depends on the difference of the fourth powers of the absolute temperatUI: es of the surfaces inclosing Hie air space. It follows that, in case the heat. passes by conduction through the solid'portion of the wall, the loss remains approximately the same so long as the temperature of the two limiting planes remains constant, no matter what may be the temperature of the two planes. On the other hand, the heat passing across the air space by radiation increases rapidly with the temperatures of the inclosing surfaces, although the difference between these temperatures may remain constant. This feature will be shown by curves in the latter part of this paper and thoroughly discussed. The important point is that the air space, which is advantageous in the walls of a refrigerator because the temperatures are low, is objectionable in a furnace wall because the temperatures are high. It is customary to put air spaces in furnace walls between the firebrick linings and the common brick. Usually the fire-brick lining is only half a brick thick, which construction brings the air space too close to the furnace. The result is that the temperatures of the surfaces inclosing the air spaces are too high, and in consequence too much heat is radiated across the spaces. The heat passing through such walls would be much reduced if the air spaces were filled with brick, or, better, with some cheap nonconducting materials, such as ash, sand, mineral wool, etc. Even where the fire-brick lining is one brick thick (9 inches), the temperature in the furnace may be high enough to raise the temperatures of the air-space surfaces so much that the heat radiated across the space will amount to more than would the heat conducted through a filling, were the filling only common brick. This last statement is amply justified by the data here presented.

Jan 1, 1911

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By L. E. Schultze

The Bureau of Mines devised a technique to recover a Zn-Pb concen-trate from a geothermal brine. More than 99 pct of the Zn and Ph was precipitated by treating the brine with H2S and controlling the pH with lime. Recycle of the sulfide precipitates increased crystal size and resulted in easily filterable products. A typical sulfide precipitate contained 53 pct ZnS, 8 pet PbS, 24 pct MnS, and 15 pct FeS. Addition of sulfide as FeS or CaS was not effective in precipitating Zn and Pb, but Zn in the brine was selectively removed with a strongly basic ion-exchange resin. A proposed flowsheet for metals recovery is discussed.

Jan 1, 1985

By Wilbur I. Duvall, S. L. Windes, Leonard Obert

"Previous investigations, too numerous to be listed in entirety, have been performed to determine the physical properties of rock. When considered according to their objectives, most of these investigations can be grouped as follows: First, the geologic group (1,2),4/ in which the purpose was to obtain information on the physical properties of the rocks that make up the earth's crust. Particular emphasis has been placed on the determination of the elastic constants--that is, Young's modulus, the modules of rigidity, and Poisson's ratio – as these quantities determine the propagation characteristics of seismic waves. Second, the structural properties group (3 - 11), in which the physical properties of architectural or monumental stone, concrete and aggregate rock, road blocks (cobblestone), and the like were desired. The tests have been quite general and include, besides the elastic properties; the compressive and tensile strength, and the toughness, hardness, and weathering properties of many types of rocks.To .a lesser degree, investigations have been carried out to determine the physical properties of mine rock. A few reports (12 - 14) present data on the crushability and grindability of mine rock, and a large number of papers discuss grinding and crushing procedures and methods of analyzing the data (for example, see references 15 - 17). Some of the latter group also have given the results of tests on mine rock; however, comparatively few include an adequate petrographic description or information on other physical properties of the rock. A few papers,(18 - 22) have reported studies of the strength of rock specimens in respect to the strength of parts of mine structures, such as pillars, roof, arches, etc. Other papers (23 - 26) have discussed investigations on such subjects as primary and secondary crushing, diamond and pneumatic rock drilling, explosive breaking and shattering of rock, rate of drifting and miring, and other allied problems. The majority of these reports have given no more than a cursory, description of the rocks and have included no statement regarding the physical properties. When statements have been given regarding the physical properties, they have usually referred only to isolated tests, making correlations between variations in the physical properties and variations in the .test under consideration difficult, if not impossible. Some reports have included handbook values on such characteristics as the crushing strength, hardness, and toughness. This practice is not satisfactory, because these values are usually given for col¬lective types of rocks, such as granites, limestones, and marbles, and it is known that the variations of the physical properties within these groups is often larger than the differences between the groups."

Aug 1, 1946

By L. E. Cardwell

This publication contains routine analyses and related source data for 390 natural gas samples from 22 States and five foreign countries. Of this total, 385 samples were collected during calendar year 1969. The remaining five analyses are of samples collected during previous years, but releases granting permission to publish the results were not received until 1969. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Eleven previous publications have presented the results of 8,660 gas analyses made by the Bureau of Mines Helium Activity prior to 1969. The first three, Bulletins 486,6 576,6 and 617,7 contain analyses and related source

Jan 1, 1970

By Frank D. Lamb, D. A. Woodard

"INTRODUCTION The iron-ore deposits near Cranberry, N. C., were worked as early as 1820, and records show that to date at least 1,500,000 tons of ore has been mined.. The early operators depended on selective mining and hand cobbing to yield a product containing 40 to 50 percent iron. Later, a magnetic concentrator was erected by the Cranberry Furnace Co. and was operated periodically until 1930. The magnetic cobbing method employed yielded satisfactory concentrates, but the plant was shut down because costs were too high. 4/Early in 1944, in connection with the sponge-iron program of the Bureau of Mines, North Carolina and Tennessee were surveyed for the purpose of finding a readily available source of high-grade iron ore for use in the experimental production of sponge iron at Salisbury, N. C., and samples from various sources were tested in the laboratory. The Cranberry ore proved to be best with respect to grade of magnetite concentrates produced, and it was decided that a pilot mill should be built on the Cranberry mine property and that the concentrate made there should be shipped to Salisbury for direct-reduction tests in a commercial brick kiln."

Dec 1, 1946

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By David K. Ingram

Research performed by the U.S. insurance industry has determined that mine subsidence is uninsurable. Consequently, the insurance industry has decided not to voluntarily offer mine subsidence insurance. The U.S. Department of the Interior has long been investigating the effects of mine subsidence. These investigations have resulted in Federal regulations and controls of mine subsidence. This U.S. Bureau of Mines report generally describes mine subsidence, the development of mine subsidence insurance programs, and the eight current mine subsidence insurance programs in the United States. The States that have these subsidence programs include Colorado, Illinois, Indiana, Kentucky, Ohio, Pennsylvania, West Virginia, and Wyoming. Major aspects of the programs include history, administrative and operational procedures, insurable structures, recognition of mine subsidence, major exclusions, claims, insurance premiums, and the economic health of each program. Addresses of agencies involved with mine subsidence insurance are also given. Information within this report can be useful for residential and commercial property owners and mine operators. States that are considering starting or have an existing mine subsidence insurance program can also use this report as a model for initiating or modifying their programs.

Jan 1, 1993

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969