Search Documents

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By Thomas C. Mowatt

Chemical and petrographic studies were carried out on selected tin-bearing rock samples of contact-metasomatic origin from the Cassiterite Creek and Brooks Mountain areas, Seward Peninsula, Alaska. The tin content of rocks ranged from 0.39 to 8.9 pct. Leaching with a 20 pct hydrochloric acid solution released from 19.3 to 67.9 pct of the tin. Cassiterite was not observed in the rock samples. These results are significant with regard to tin recovery and reserve delineation in these and similar occurrences. Part of this leachable tin may be associated with metasomatic borate minerals.

Jan 1, 2011

By A. M. Gaudin

A study of the consumption of reagents used in flotation gives useful data as to the market which employment of the flotation process creates for the manufacturers of the necessary chemicals and oils, and furnishes a useful clue to the trends in flotation practice influencing the choice of reagents used and the' extent to which new reagents are displacing less suitable older reagents. In the present investigation an attempt has been made to cover both of these phases of the consumption of reagents in flotation. Unfortunately, however, the data collected in tie various districts have not been equally informative; some operators have reported very completely both the consumption of reagents and the metallurgical results obtained therewith, while others were apparently unable to supply these figures in sufficient detail to meet the requirements of this investigation. RESULTS OF INVESTIGATION Table 1 gives the tonnage of ore treated by flotation, as reported. This table shows that flotation has been most largely used in the concentration of copper ores, next in complex lead-zinc ores, followed by lead ores, zinc ores, miscellaneous ores, and copper-iron ores.

Jan 1, 1929

By Thomas Brunsing

The program was carried out to develop deep kerfing and core breaking techniques to be incorporated into the design of a field prototype hard rock mining machine. The field machine is designed to mine non-abrasive bedded deposits up to 20,000 psi in uniaxial compressive strength. The mining technique involves cutting approximately 2 ft deep parallel kerfs spaced 2 ft apart in either a horizontal or vertical direction and subsequently breaking out the cores so defined. The prototype machine is intended for demonstration of the technique in a quarry or equivalent field environment. The program was aimed at minimizing the required kerf width, obtaining reliable breaking within that kerf width and determining cutter blade requirements necessary to achieve a mining rate of 20 ft3/min. Full scale breaking experiments and 1/2 scale kerfing experiments were employed to evaluate the system. High strength concrete test specimens were used to simulate the rock being cut and broken. The test results indicate the kerf/break technique can achieve the desired mining rate by utilizing two 7 ft diam blades to cut 2 in. wide by 24 in. deep kerfs. A lateral load applied at the base of the kerf (base shear) was selected at the core breaking technique to be employed by the full-scale prototype machine.

Jan 1, 1983

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

Since March 28, domestic producer prices on 99.5 percent aluminum ingot have been at 5l¢ per pound. Dealers in this same time frame have held ingot quotes at 49¢-50.5¢ per pound. COBALT: Imports from southern Africa in 1976 constituted 73 percent of total cobalt imports. Moreover, the United States is 98 percent dependent on imports of cobalt. For this reason, the Bureau of Mines is closely monitoring developments abroad to ensure an advance notice of any possibility of a shortfall in supply. Included in these imports were those from Zaire (41 percent directly from Zaire and 15 percent via Belgium-Luxembourg), Zambia (11 percent), and Botswana (6 percent). Also being closely watched are industry stocks.

Jan 1, 1977

By R. V. Ramani

The overall objective of this study is to contribute to the reduction of the quartz dust hazard in underground coal mines through a better under-standing of the sources and generation of airborne quartz dust. This research project has included extensive experiments in operating mines for (1) documenting the amount of respirable dust generated, (2) measuring the quartz levels in host materials and airborne dust, (3) analyzing the size consist of the mined product, and (4) establishing the relationship between these various parameters. The results of the study indicate that the amount of dust airborne is a very small fraction of the total (<15 µm) and respirable (<7 µm) dust generated. The quartz contents in the total and respirable airborne dust are generally higher than those in the host material. Quartz content increases with decreasing size of airborne dust. Also, it appears that rock breaks into a different size distribution than coal. The source of quartz for the airborne dust appears to be the roof and the floor material rather than the coal seam itself. No general relationship is found between the Hardgrove Grindability Index and either the quartz content in the airborne dust or the amount of respirable dust. Extended descriptions of the experimental design, the experiments, data analyses and results are presented in this volume. The raw data, the data management computer program and the sampling and safety plan are presented in Volume 2.

Jan 1, 1987

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Charles B. Carpenter

For many years, studies of ground movement and subsidence accompanying subsurface mining operations have been part of the research program of the Bureau of Mines. Periodic observations by engineers of the Mining Division of the Bureau of man-built structures beneath which mining operations are conducted offer indisputable evidence of subsidence in the form of creeks in masonry structures and fractures and depressions in tie surface of the earth. As the removal of subsurface rock and earth material by mining, especially by the room-and-pillar method, is equivalent to withdrawing some of the foundation of a building, subsidence of the formations above, the mining levels in certain air-as is easily understood as a gravitational adjustment of the overlying earth formations.

Jan 1, 1940

By Charles B. Carpenter

For many years, studies of ground movement and subsidence accompanying subsurface mining operations have been part of the research program of the Bureau of Mines. Periodic observations by engineers of the Mining Division of the Bureau of man-built structures beneath which mining operations are conducted offer indisputable evidence of subsidence in the form of creeks in masonry structures and fractures and depressions in the surface of the earth. As the removal of subsurface rock and earth material by mining, especially by the room-and-pillar method, is equivalent to withdrawing some of the foundation of a building, subsidence of the formations above, the mining levels in certain areas is easily understood as a gravitational adjustment of the overlying earth formations.

Jan 1, 1940

By W. H. Oppelt

A small, annular-retort gasifier having a nominal capacity of 40 pounds of lignite per hour was designed and constructed at the Lignite Experiment Station, Grand Forks, N. Dak. The purpose of the investigation was to increase the capacity of an annular-retort gasifier by better temperature distribution in the heating chamber (adjacent to the annulus) and by supplemental internal heating with controlled amounts of air. Correct control of air admission should yield crude ammonia-synthesis gas having a (H2+CO)-N2 ratio of 3. Dakota Star stoker-size lignite was used during the exploratory experimental program. The effects of temperature level and distribution in the heating chamber and of addition of air to the reactor were investigated. Hydrogen - carbon monoxide ratios ranged from 1.9 to 2.5, and (H2+C0)-N2 ratios were as low as 2.9. Hourly gas production ranged from 970 to 2,580 cu. ft., or 62.0 to 164 cu. ft. per sq. ft. of heated surface, or 350 to 940 cu. ft. per cu. ft. of reactor volume. Data from the small gasifier could be readily correlated with those previously obtained in the commercial-scale unit under comparable experimental conditions.

Jan 1, 1957

By Tell Ertl, Ernest E. Burgh, John R. Wagner

The principal goal of the Oil-Shale Mining Division is to develop the most economical methods and practices for mining oil shale. Experimental work in the mine has not progressed far enough to conduct full-scale breaking tests; therefore, mining season - to October 31, 1945, has been confined largely to problems connected with drilling cost oil shale. Calculations have indicated that commercial production will result in breaking the oil shale; the largest individual turn will be for drilling. This paper is a report on the progress of phase two of drilling research to date; it outlines the development of a successful hard-surfaced rock bit for drilling oil shale.

Dec 1, 1948

By Donna lynne Anderson

This report documents the status of a laser-based underground guidance system for tracking and controlling the movements of underground mobile mining equipment. This research is part of a multiple project effort at the U.S. Bureau of Mines to increase mine safety and efficiency by developing technology for computer-assisted mining. Guidance systems, which can track and control the movements of underground mining equipment, are essential during computer-assisted mining operations. A continuous mining machine at the Bureau&apos;s surface test facility served as the test-bed for initial development and experimentation of this guidance system. Subsequently, a continuous mining machine in an underground mine served as the platform for in-mine experimentation The first section of this report includes details of the laser sensors, communication network, and computer hardware. The next section includes experimental results, which show the system capable of accurately tracking and controlling the tram maneuvers of a continuous miner underground. The final section discusses conclusions and recommendations.

Jan 1, 1992

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987