Search Documents

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

By Irving Wender

This report describes Bureau of Mines experiments and reviews the work of others on the exposure of coal and coal-derived products to gamma rays and some other types of radiation. Results are presented on tests of three bituminous coals and a lignite that had been pulverized to minus 200-mesh particles and exposed to 1,000 megaroentgens of gamma irradiation from spent-fuel elements of a nuclear reactor. Of about 20 chemical and physical tests in Bureau work, only mass spectrometry of gases evolved during vacuum pyrolysis of the coals to 450° C gave results indicating differences in the irradiated and unirradiated samples. Mass-spectral distribution curves for CO and CO2 evolution showed fewer irregularities (reversals of curvature) for irradiated coals; thus, mass spectrometry appears to be the most sensitive method for determining radio-induced changes in coal. It is concluded that coal is not significantly altered by gamma irradiation owing to the resistivity of its highly condensed ring structure. High-level gamma irradiation, therefore, is unlikely to prove advantageous in coal processing and utilization. Specially treated coals, because of resistivity of coal to radiation damage, may be useful as an absorbent in processing radioactive wastes.

Jan 1, 1968

By Peter D. Lohn

The Bureau of Mines conducted both laboratory and field investigations to study the effectiveness of medium-pressure (up to 30,000 psi) water jets in controlling the generation of airborne respirable dust during the hydraulic fragmentation of coal. Laboratory studies were conducted at the Farmington High Energy Test Site of the Twin Cities Mining Research Center, and field studies were carried out at the Humphrey No. 7 mine, Mount Morris, Pa., in the Pittsburgh coalbed. The water jets were produced by commercially available triplex pumps. The dust samples were collected by midget impinger samplers, and analyzed by electronic and optical counting techniques. Respirable dust concentration for a full-scale production model was projected at below 2 mg/m3, the maximum exposure allowed by the Federal Coal Mine Health and Safety Act of 1969.

Jan 1, 1975

By James H. Snyder

This final report presents results of a program to develop a new conveyor system, adaptable to existing miners or loaders, which reduces the noise level to 90 dBA without reducing machine performance. The trial conveyor design consists of a main conveyor and a swinging tail conveyor. The main conveyor incorporates a rubber-covered return guide roller, rubber mounting of pillow blocks, rubber cover of the return bed, and a rubber belt running between the flight chain and the conveyor bed plate. Testing took place in a surface coal pit and underground at the Peabody Spur Mines in Boonville, Indiana. Noise Levels as low as 90 dSA were observed on the surface and 93/94 dRA underground. Recommendations for further work are also presented.

Jan 1, 1976

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

This publication summarizes, for all interested parties, the research, development, and demonstration in-house projets programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By Corale L. Brierley

Beneficiation of phosphate in the southeastern United States generates a slurry of finely divided clay. These clay-wastes are impounded to allow the particulates to settle. The aggregation of phosphatic clay-slime wastes and slimes produced from potash beneficiation by microbial processes was studied using several bacterial species known to produce polymeric substances. Experiments included flocculation capacity of clay-slimes by whole cells, the determination of respiratory activity of whole culls in the presence of phosphatic clays, observation of clay flocculation rates by polymers derived from these organisms, and clarity of polymer-flocculated clay suspensions. The polymer-producing organisms exhibited little capacity for flocculating phosphate and potash clay-slimes. Fungal spores of Cladosporium cladosporioides (isolated from a phosphate clay-waste impoundment), when agitated with clay-slime for several days, caused the clay to form pellets. Separation of the clay/fungal pellets (density 1.1 g ml-1) from the process water might he possible using a screening technique. Studies with C. cladosporioides included the determination of suitable energy substrates and supplements for growth, absorption studies of a pigment produced by the organism, determination of the time required for bioflocculant production by the organism, and an elucidation of the conditions required for the pelletization of clay-slimes by the fungus.

Jan 1, 1982

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

To develop more accurate means of measuring low ventilating air velocities in underground mines to facilitate compliance with ventilation standards. The Approach: A commercially available vane anemometer which produces an electrical, rather than a mechanical, output was coupled to electronic circuitry to produce the Bureau&apos;s Digital Low Velocity Anemometer (see photo). [ ] How It Works: The experimental instrument has a vane anemometer head which produces an electrical output signal with a frequency directly proportional to the rotating speed of the vane anemometer shaft. The commercially available ABBIRKO FLOWMASTER anemometer head was used in this instrument. In the signal conditioning circuits the electrical signal from the anemometer is converted into pulses, which are counted during either 3-second or 1-minute intervals, depending on the position of the operator&apos;s control switch. (Readout is either "instantaneous" or averaged for a period of one minute.) The number of pulses counted is then translated (integrated and divided by a constant) in the logic circuits to get average speed. Average air velocity in feet per minute is displayed in illuminated digits. (See simplified diagram of circuitry.)

Jan 1, 1975

By H. F. Yancey

About 65 percent of the more than 400 million tons of coal produced annually in the United States is mechanically cleaned to remove the inorganic impurities before being sent to market. The impurities, principally shale and clay with some pyrite, average about 20 percent of the raw coal treated. Nearly 95 percent of the tonnage is treated by wet processes, in which water, suspensions of solids in water, or occasionally calcium chloride solutions are employed. Difference in density of coal and impurity is the basis of these processes. Of major importance in the separation is the competency of the impurities, that is, the resistance of the impurities to size disintegration in water. In general, the impurities are more resistant in geologically older coals or those in effect made older by metamorphism. If the impurities suffer reduction in particle size when immersed in water, the separation of organic from inorganic material becomes more difficult, Recently the Scientific Department of the National Goal Board (Great Britain) undertook fundamental research into the interaction of shale and water and also developed an empirical method of assessing shale breakdown or disintegration. 6

Jan 1, 1962

By Dale R. Ralston

This investigation was divided into two major phases. Phase I of the study was an examination of the occurrence and production of acid water within the Bunker Hill Mine in northern Idaho. The second phase of the project involved the study of water movement through an abandoned tailings pile. Mineralogy and hydrogeology were determined to be the two most important factors in the acid mine drainage problem. Low pH water was formed in the mine in areas of lead-zinc ore rich in pyrite. Water movement in the mine was important in the production of acid and the transportation of heavy metals. Areas of recharge to the mine were identified. A data collection network was installed to monitor water quality and quantity changes. The quantity of acid drainage from the mine was found to vary directly with surface runoff events. The study of the abandoned tailings pile was performed to determine the characteristics of water movement through the tailings material and the resultant impact on the hydrologic environment. The Page Tailings Pile, abandoned in 1969, was utilized as a study area. An extensive network of piezometers and meteorological data collection sites were installed in and near the pile. Data collected to date indicate the presence of a ground-water mound under the east half of the pile. Some transfer of ions from the tailings pile to the ground-water system has been detected.

Jan 1, 1973

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user&apos;s manual, including a program listing, is included in the appendices.

Jan 1, 1974

By R. D. Saltsman

This report is in fulfillment of Contract No. H023001.5 awarded to Bituminous Coal Research, Inc., on November 15, 1972. The scope of the work under this contract was to perform a two-phase survey for the purpose of determining the status of work in the following specific areas of industry needs under the Technology Transfer Program and to increase industry&apos;s awareness of research efforts under the Federal Coal Mine Health and Safety Act of 1969 6f (P.L. 91-173): 1. Research and development of respirable dust sampling instruments which will more accurately collect the respirable Cuss as defined by the Federal Coal Mine Health and Safety Act of 1969. 2. Development of a better means of control of respirable dust and float dust.

Jan 1, 1973

Since its creation in 1910, the Department of the Interior&apos;s Bureau of Mines has pioneered in the development of mineral technology, through research. From the very beginning, research on mine health and safety has been a dominating concern, and a responsibility that expanded markedly as a result of the Coal Mine Health and Safety Act of 1969. Until the mid-1970&apos;s research on fuel technology and coal production also was an important part of the Bureau&apos;s work. But in the four years following the 1973 oil crisis, Congress established a reorganized Federal energy research apparatus in which all fossil fuel research-encompassing extraction, use, and conservation-was centralized. Today, the Department of Energy houses Federal research on coal mine production technology, while research on coal and noncoal mine health and safety and environmental technology, and on noncoal mine production technology, remains in the Interior Department as a continuing responsibility of the Bureau of Mines. In carrying out its authorized research programs, the Bureau conducts both short- and long-term re-

Jan 1, 2012

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962

By Vernon Helm, John S. Ball, Welton J. Wenger, William E. Haines

"INTRODUCTION Although the presence of sulfur causes many petroleum’s to be classified as ""low-grade"" because of the difficulties encountered in manufacturing products to meet rigid specifications, the petroleum industry is finding it necessary to use such crude oils to satisfy present needs. As the demand for petroleum products increases, and available reserves diminish, this utilization of high-sulfur crude oils will be accentuated. Programs designed to supplement the supplies of fuel available from petroleum by the manufacture of synthetic fuel from natural gas, shale oil, and coal are in progress. Such fuels, especially shale oil and, less so, oil from the hydrogenation of coal, also contain sulfur compounds which must be effectively removed. Thus, the need for fundamental research on the sulfur compounds that may be expected in petroleum and allied products is becoming greater as the industry is forced to call upon all available resources to meet the demand for petroleum products. In recognition of this need, the Bureau of Mines has inaugurated a long-range program assigned to furnish fundamental data concerning the presence, characteristics, and effects of sulfur compounds in petroleum and its products."

Dec 1, 1946

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981