Search Documents

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau's efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By Gerald T. Homce, James C. Cawley

Electrical arcing injuries are the most common form of electrical injury in mining. MSHA data show that 381 "non-contact electric arc burn" injuries occurred in the mining industry from 1996 - 2005. A more detailed study of data from 1990-2001 showed that five types of apparatus - circuit breakers, conductors, nonpowered hand tools, electrical meters and test leads, and connectors and plugs were involved in two-thirds of the lost workday injuries. Many of the protections from electrical arcing injury available to workers in other industries stem from the application of National Fire Protection Association Standard 70E - Standard for Electrical Safety in the Workplace (NFPA 70E). NFPA 70E is a generally accepted industry guideline document, but excludes underground mining from its scope. Many of its practices and procedures, however, can be applied in the mining workplace to supplement the existing electrical safety requirements of Title 30 Code of Federal Regulations. This paper describes how NFPA 70E can be applied to mining workplaces after an analysis of the mine power system electrical arcing hazards has been completed (and Hazard/Risk Categories determined) using the tables from NFPA 70E or the calculation method as described in IEEE 1584. NFPA 70E can then be used to determine the levels and types of personal protective equipment (PPE) needed to protect miners against burn injuries. Appropriate lockout and tagout (LOTO) procedures for use in the mining industry are also described. Suggestions for better selection of electrically-rated hand tools are included. Recommendations for electrical meter selection and use based on transient withstand capability are also discussed.

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By K. E. Robinson

This study is the extension of an investigation of reclamation of floodplain areas in the Coeur d'Alene Mining District, Idaho, that are unuseable in their natural condition, by construction of landfills with mill tailings. The study develops a valley-wide tailings disposal plan to utilize 20 potential landfill sites on floodplain areas and presents measures for reclaiming the sites for subsequent productive use. Field and laboratory testing on a test section and two abandoned impoundments support the use of hydraulically deposited tailings for landfill construction. Hydrological testing has shown that controlled discharge from tailings impoundments results in contaminant levels in the discharge below regulated standards. Additional testing indicated that compacted soil liners and pond management provide adequate contaminant abatement where acid-generating tailings are encountered. Mechanical compaction, including surcharge loading, upgrades foundation support capacity so that construction on the surface of tailings deposits is feasible. On completion of the testing program, the test sections were abandoned and rehabilitated. Details concerning potential landfill sites have been refined. At recent production rates, the 20 sites would result in 680 acres of reclaimed land, while providing a minimum of 40 years of tailings storage capacity. A general design has been developed for the retention dikes. Aspects of embankment stability, including liquefaction are discussed, and are shown to provide an adequate factor of safety under the anticipated range of operating conditions.

Jan 1, 1983

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By Larman J. Heath

Preliminary results of an explosive fracturing-solvent injection heavy oil recovery experiment conducted by the Bureau of Mines at a shallow oil reservoir near Bartlett, Kans., are given. Three wells 35 to 50 feet apart were drilled to a depth of 360 feet, and an open hole interval from 300 to 350 feet in the Bartlesville Sandstone Formation was explosively fractured with 3,000 pounds of pelletized TNT in each well. Laboratory tests were made on cores obtained from these wells to confirm the suitability of using an aromatic-type solvent. Injection of a 74-percent aromatic solvent was begun into one well and continued intermittently for approximately 2 months. Crude oil production amounted to 29.6 bbl, or 11.7 percent of the total oil con¬tained within the three-well interwell zone.

Jan 1, 1972

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996