Search Documents

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By B. W. Haynes

This Bureau of Mines report describes the laboratory processing of manganese nodules and the results of tailings characterization obtained during the cooperative program with the Department of Commerce's National Oceanic and Atmospheric Administration (NOAA) and the Bureau. Five technically feasible first-generation nodule processing methods were operated at bench scale to generate sufficient tailings and slags for physical and chemical analyses. A description is given for the laboratory operation of the individual unit operations of each process. The laboratory-generated tailings and slags were tested for physical properties, mineral content, elemental and ion content, and leachability for all five processes. The results of leachate testing using the Environmental Protection Agency extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the EPA-U.S. Army Corps of Engineers seawater elutriant test showed very low to negligible leaching of metals from the tailings and slags. Results of the EP toxicity test demonstrated that the wastes are nonhazardous as defined in the Resource Conservation and Recovery Act (Public Law 94-580).

Jan 1, 1985

By Jr. Gabler

The U.S. Bureau of Mines (USBM) has developed a computerized commodity flow model for strategic and critical materials This flow model is generic and applicable to most commodities and amenable to updating supply, demand, and/or production data change. The original model, with slight modifications, was used to track the flow of chromium. This report follows the flow of chromium through its metallurgical, chemical, and refractory applications, and highlights areas where significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing 451,769 mt of chromium were consumed, including 99,221 mt of chromium from recycling, Chromium losses from all causes in 1989 were estimated to be 345,347 mt from a variety of areas. These areas and their chromium losses are as follows: processing losses, 38,825 mt; processing-downgraded scrap, 18,227 mt; manufacturing losses, 18,128 mt; manufacturing-downgraded scrap, 56,595 mt; prompt scrap exported, 1,531 mt; obsolete scrap exported, 43,443 mt; recovery losses, 155,529 mt; and recycling losses, 13,069 mt. Recycled chromium-containing material accounted for 22 pct of the apparent consumption of chromium in 1989.

Jan 1, 1994

By FREDERICK H. WILLCOX

In the past the blast-furnace industry was under the stigma of being one of the most prolific sources of killed or seriously inj ured and permanently disabled workmen of any of the industries of the country. In the popular mind, labor at blast furnaces was little less hazardous than mining, powder making, or railroad work. This impression wasbased not so much on definite knowledge of the number actnally injured and the causes of injury as on the spectacular nature of the accidents that from time to time were described in the press. As with a mine disaster or a railroad wreck so with many furnace accidents, the number fatally injured in such accidents constitutes only a minor proportion of the workmen who suffer more or less serious injuries. However, the reader of the daily paper receives a distinct impression-of frightful and sudden disaster which is apt to be associated henceforth in his mind with work at blast furnaces. It is true that in the past this impression has not been without warrant, for from the time of the advent of Mesabi ores, taller furnaces, and faster smelting, which begain in the early nineties, the newspapers have chronicled a large number of blastfurnace disasters. Blast-furnace men have never assumed to tolerate failures in construction or defective control of furnaces. But the admitted hazards of the work are many, and the slow development of improvements in the construction and control of the furnace and its auxiliaries have occasionally given rise to a tendency to accept as a part of the day's work not only the unforeseen and difficultly controlled accidents but accidents whose recurrence might be stopped by the adoption of suitable preventive measures. In the smelting of iron, even more than in many other industries, safety is inseparably related to efficiency in production, and. the accidents strictly incident to work about the furnace are proportional in some degree to the success with which obstacles to smooth working are overcome. This relation does not hold, however, in regard .to such accidents as are incident to hand labor, falls, falling and flying objects, machinery, and the use of hand tools.

Jan 1, 1917

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By Svend [Bue] Rondum

The final report contains a summary of the work performed under this contract, In addition to the report itself, other products were derived from this effort. Several hardware items were prototyped for use with underground belt conveyors, and a manual for installation and maintenance procedures was developed and published under separate cover. Recommendations have been included for implementation of the tools and the manual or, an industry-wide basis.

Jan 1, 1982

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By Pablo Velasco

The Belize economy recorded modest growth during 1980; the growth of the gross domestic product (GDP) in real terms was between 1% and 2%. At current prices, the 1980 GDP reached $108 million2. This output was largely attributed to the performance of a few industries, mostly nonminerals. Such performance improved significantly the balance of payments situation by reducing the deficit from $19 million in 1979 to $4 million in 1980. The rate of inflation was an estimated 18% in 1980 and would have been greater if not for a conservative monetary policy and price control on a number of essential items. Expert earnings increased $43 million, or 50%, from the 1979 level. After increasing more than 25% in 1979, imports increased only 6% in 1980 to a level of $141 million owing to the decline in investment and stabilization of petroleum prices. The balance of trade deficit was $9.8 million in 1980, a marked improvement from the 1979 level of $45.1 million. The mineral output for Belize accounted for only a fraction of 1% of the GDP. Such activity was limited to the production of limestone, marl, and sand and gravel, all of which were primarily used in construction of the Northern Highway between Orangewalk and Belize City. Mineral resources are deficient or nonexistent in Belize for the majority of metals and nonmetals, although the Government and others continue to believe that petroleum must exist in Belize. The proximity to Mexican oilfields and the growing finds in the Peters area of Guatemala support this expectation. The Government continues encouraging exploration onshore and offshore and offers terms that

Jan 1, 1982

By Earl F. Hastings

The Pilgrim mine, operated by the Pioneer Gold Mining Co., is 9-1/2 miles west of Chloride in the Pilgrim mining district on the eastern slope of the Black Mountains, or River Range, Mohave County, Ariz. In March 1937, 100 tons of gold ore per day were being mined and milled at the property by a total force of 5i men. Climatic conditions allow year-round operations. Due to present activity in the county there is an ample supply of labor for the requirements of the mine. The Pilgrim is the only producing property within s radius of 6 miles; recently, however, the South Pilgrim Mining Co. has launched a development campaign on claims that adjoin the Pioneer Co. property to the south.

Jan 1, 1937

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By J. J. Lukasko

The U.S. Bureau of Mines developed an alternative electrochemical process for the production of calcium metal. The current industrial practice is costly, complex, and inefficient. The Bureau method involved electrowinning of a calcium-tin alloy followed by electrorefining to produce calcium metal. In the electrowinning cell, CaCI2 was fed to a KCI2-CaCI2 electrolyte. The calcium was electrowon at 6500 C into the pure molten tin cathode until the cathode contained 7.5 wt pct Ca. Current efficiency for electrowinning averaged over 90 pct. The resulting calcium-tin alloy served as the anode for the electrorefming cell, which employed a [CaC~-CaF2] fused salt as the electrolyte. Calcium metal was electrorefmed at 8500 C with a current efficiency of 85 pct based on calcium metal recovered. The calcium metal analyzed 99.2 pct, which is purer than commercially produced calcium.

Jan 1, 1990

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By Ernest W. Johnson, F. E. Cash

"INTRODUCTION Mine operators have long realized the importance of providing a satisfactory and dependable means of giving prompt warning to underground mine workers at the occurrence of a mine fire or other threatened disaster.Most underground mines of the Lake Superior district are prepared to inject a stench liquid into the compressed-air system quickly to give such warning. The liquid evaporates quickly and gives off an intense and easily recognizable odor even when present in minute quantities in the mine air. Workers in the mines studied have been fairly generally familiarized with the odor and instructed as to evacuation procedure when the warning odor is detected.In some mines provided throughout with electric lighting, including working faces, a prearranged light-flashing signal is given as a warning supplementary to that received from the stench.In a few mines, workers have been instructed to evacuate the mine immediately in the event the compressed-air supply is cut off, regardless of whether mechanical failure may be involved.Information obtained in observing a number of stench-injection tests is compiled and presented in the hope-that it will serve as an incentive to provide means of making stench injections at mines not now so equipped and for making similar tests at other underground mines, so that in case unsatisfactory results are obtained rectifying adjustments or changes may be made in time. It is further hoped that this paper will bring out the real importance of repeating these tests from time to time, at least once a year on each operating shift, so that in the event of an actual emergency, underground employees will receive a prompt warning."

Nov 1, 1945

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986