Search Documents

By M. John Brodie

This report reviews the regulatory environment as it pertains to tailings management and disposal from mining operations, excluding coal and placer gold operations, in the state of Alaska. It is based on the EPA's staff position on an effective program to regulate mining wastes as presented in the May, 1990 Strawman II document, The unique conditions which occur in parts of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a railings disposal facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection are examined.

Jan 1, 1992

By Stephen W. Lambert

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By Joseph Daniels

[Adequate supplies of suitable coal and coke are prime requisites in many industries, particularly those dealing with the utilization of mineral resources, recently interest has been focused on the possibilities of using electricity produced at Bonneville and Grand Coulee, Wash., in many electrochemical and electrometallurgical processes, in which core or some form of carbon is necessary in addition, discussion has been revived on the possibility of making iron and steel by the conventional methods employed in blast and open-hearth furnaces. The subject also is important at this time because of its relationship to industrial preparedness for national defense. A supply of coke from local sources on the Pacific coast is necessary in any program of production for strategic sufficiency of certain materials. An anal trio involving tae establishment of such industries should include detailed data on available supplies of coal, the quality and properties of the coke produced, and the technologic and economic factors involved in manufacture of echo and disposal of byproducts.]

Jan 1, 1941

By W. M. Dressel

The Federal Bureau of Mines has obtained data by differential thermal analysis of the various minerals that represent the nation's resources in manganese. These data are supported by X-ray diffraction analysis, chemical analysis, mineralography, and optical mineralogy, and provide fundamental information on the response of each mineral to thermal treatment in oxidizing, reducing, and neutral atmospheres. The information can be applied advantage¬ously in the identification of manganese minerals. Its greatest potential value, however, lies in the application of the quantitative data on the reaction temperatures, rates, and products to the more efficient extraction of manganese from U.S. ores. Thermal analysis curves are presented for certain manganese minerals, namely hausmannite, bixbyite, braunite, pyrolusite, lithiophorite, cryptomelane, hollandite, manganite, rhodochrosite, and rhodonite. The original minerals and the products of their thermal decomposition were identified by X-ray diffraction analysis, supplemented by chemical analysis and mineralogical identification.

Jan 1, 1961

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By William Seymour, L. D. Schmidt, J. W. Myers, W. T. Reid

"This investigation was conducted by the Bureau of Mines as part of a program of the Solid Fuels Administration to encourage the utilization of anthracite fines, the objective being to determine the practicability of using anthracite fines in the manufacture of packagedThe experimental loss of packaged fuel covered by this report were made at a commercial plant using the Glenn Smith process and ordinarily making packaged fuel from Pocahontas screenings. These lots included several made from straight antimacite mines and others made from various blends of anthracite fines with four different bituminous coals. In all cases an asphalt binder was used. Determinations of the physical properties and the cobustion characteristics o the various samples of packaged fuel were made by the. Bureau of Mines at the Central Experiment Station.The physical tests indicated that a packaged fuel of sufficient strength for ordinary handling can be made from straight anthracite coal or from a wide variety of blends of anthracite fixes with bitunimous coal, using asphaltic binder. However the combustion tests indicated that packaged fuel made from anthracite alone tended to crumble excessively during burning and that as much as 30 to 50 percent of a caking coal may be required In the mixture to produce a block having satisfactory combustion characteristics.The authors wish to acknowledge the. splendid cooperation of Messrs. H. W. Kelly, J. L. Mooney and C. H. Stoss of Columbus, Ohio, who were chiefly responsible for obtaining the materials and making all the arrangements necessary for the production of the packaged fuel for testing.Thanks are due to the officials of Carnegie Institute of Technology for the use of their Olsen. Testing Machine and to H. M. Cooper and W. A. Selvig of the Bureau of Mines for analyses and tests."

May 1, 1946

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

By K. Biswas, S. Iverson, S. J. Jung

Computer modeling of rock flow in ore passes is being investigated and compared using MSC Soft-ware’s Working Model 2D1 (WM2D) and Itasca Corp.’s Particle Flow Code in Two Dimensions (PFC2D). This work is being carried out by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health to determine the usefulness of computer modeling to improve ore pass design. The types of tests included pendulum tests to validate WM2D simulations and simulated single-rock drop tests in both WM2D and PFC2D to understand their contact models. Simulated rock impacts at the ore pass chute and the use of inclined ore passes and doglegs were investigated in both programs. A PFC2D simulation showed that dynamic loads at the chute gate were reduced significantly when a dogleg transition was used, and simulations in which the ore pass was inclined showed significant reductions in chute impact loads compared to simulations of a vertical ore pass. A released hang-up was simulated using PFC2D.