Search Documents

U.S. Minerals Coordinating Council Advised. -The Critical Materials Act of 1981, H. R. 4281, introduced on July 27, would create a Council on Critical Materials in the White House Executive Office to oversee Federal materials programs involving $1 billion committed to research by 14 agencies, and to serve as the President's focal point to evaluate materials policy. It was introduced by Congressman Fuqua (D-Fla.) whose Committee on Science and Technology has over-sight over the implementation of P. L. 96-479, the National Materials and Minerals Policy, Research and Development Act of 1980. Bulgaria's Mineral Bank. -Recently Bulgaria established a mineral bank to facilitate receipt of foreign credits for exploiting Bulgaria's mineral raw materials. The bank has wide powers to enter into business arrangements with foreign creditors. Bulgaria's main interest in trading with the West is to import the technology for developing energy and mineral resources.

Jan 1, 1981

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By R. L. Thorne

The Snettisham Peninsula, 30 miles southeast of Juneau, Alaska, was studied by the Bureau of Hines to obtain basic information about the size, grade, and metallurgical characteristics of a large basic intrusive containing titaniferous magnetite. The investigation, which was part of a continuing program to determine the potential reserves of iron and titanium ores in Alaska, included transit and magnetometer surveys, followed by diamond core drilling and metallurgical testing. The magnetic attraction of a part of the Snettisharn Peninsula is noted on early navigational charts prepared by the Coast and Geodetic Survey. Reconnaissance examinations by the Geological Survey and a preliminary dip needle survey by the Territorial Department of Mines indicated the general nature of the basic intrusive, but little was known as to the grade and extent of the magnetite mineralization. The detailed survey by the Bureau of Mines proved an area of approximately 390 acres in which generally high magnetic anomalies with exceptionally high localized anomalies occur. Subsequent drilling across B representative section of the deposit yielded core samples, which assayed from 11 percent to over 45 percent total iron. A large sample of core composited to represent the drilled portion of the de-posit assayed 18.9 percent Fe, 2.6 percent Ti02, and 0.29 percent S, 0.32 percent P, and 0.05 percent v.

Jan 1, 1956

By Robert B. Hoekzema

The Bureau of Mines and U.S. Geological Survey completed a 4-yr (1979-82) mineral appraisal of the Chugach National Forest (CNF), AK. This report summarizes the Bureau's placer gold studies in the CNF. Placer mining from the mid-1890's through 1982 produced an estimated 133,800 oz of gold, of which two-thirds was produced prior to 1920. As much as 6,800 oz of placer gold was produced from 1979 to 1982. Most production came from Crow, Canyon, and Resurrection Creeks. Five types of placer gold deposits were identified in the CNF: (1) alluvial placers, (2) bench placers, (3) eluvial placers, (4) glacial placers, and (5) marine placers. Placer sampling indicated a potential for gold production from alluvial and bench placers associated with historically mined drainages such as Crow, Canyon, Resurrection, Sixmile, and Mills Creeks and from unmined drainages including the Avery, Kings, Snow, Copper, and Tasnuna Rivers and several smaller streams throughout the CNF. Results of fineness tests indicated that gold from the CNF ranges from 455 to over 950 fine. Subsequent investigations in drainages with anomalous placer sample values also identified previously unknown lode mineralization.

Jan 1, 1986

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

By Russell E. Griffin

The current state-of-the-art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in underground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long-term in-mine tests are presented.

Jan 1, 1979

By W. L. Falke

This Bureau of Mines report illustrates critical path planning and scheduling techniques as applied to typical mining operations. Detailed examples of arrow diagramming and computer oriented applications of critical path methods are given. Program Evaluation and Review Technique (PERT) is discussed briefly in comparison to the Critical Path Method (CPM).

Jan 1, 1966

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau's Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

By K. C. Dean

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Stabilization has been attained by physical, chemical, vegetative, and combination procedures. Vegetative reclamation is preferred to physical and chemical stabilization but is diffi¬cult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Methods now have been developed for attain¬ing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $120 to $650 per acre. The cost for stabilizing tail¬ings requiring more intensive treatment techniques may range upward to $1,750 per acre. This report summarizes procedures developed by the Bureau of Mines and industry for vegetating amenable tailings, lists costs for the various processes, and suggests procedures that may be applicable for stabilizing saline and pyrite-containing tailings. Ridged planting beds, drip irrigation, and deep-furrow planting techniques are suggested for stabilizing saline wastes. A combination of mill tailings and sewage sludge can be used for pro¬ducing synthetic soils, and layers of sewage sludge buried under a layer of tailings offer promise of inhibiting acid formation from oxidation of sulfides in mineral wastes.

Jan 1, 1974

By J. E. Dooley

A mass spectral scheme of analysis was devised which can be used to identify individually a single compound from a larger group of similar compounds. Mass spectra for 32 alkyl aryl sulfides are provided for future reference work, and analytical correlations used in producing the analytical scheme are discussed. Some of the correlations show that base peaks are either the same mass as the parent peaks or may be derived from cleavage alpha to the sulfur atom with migration of one hydrogen to the sulfur atom. Other spectral consistencies provide means of separating ortho-, meta-, and paratolyl arrangements in an overall analytical scheme. Determinations of chain lengths and separation of isomeric species are also discussed.

Jan 1, 1972

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By G. H. Damon

Since 1963, Bureau of Mines Information Circular 8179 has served the mining industry as a fundamental safety guide in the field of blasting agents. In the intervening 14 years, many changes have occurred, and this report presents revised and new recommendations which recognize these changes. For example, AN-FO is now supplied mostly premixed, whereas in 1963 much of it was mixed by the blaster; aluminum metal (A1) and other fuels are now often added to AN-FO to increase strength, and flake aluminum powder is used as a sensitizer in water gels; and water gels or slurries that are now extensively used were just coming into practical use in 1963. To provide the widest possible margin of safety, some of the Bureau's recommendations are more stringent than existing regulations,

Jan 1, 1977

By Terry J. Kreidler

In recent years, west-central Arizona and adjacent California have become the focus of geologic and exploration attention because of its excellent exposure of detachment-fault terrane. Detachment faults, normal faults with nearly horizontal fault planes, are the result of regional extension. Rocks on the lower plate consist of mylonitized intrusive, metasedimentary and crystalline rocks highly altered to chlorite; upper plate rocks comprise sedimentary, volcanic, metasedimentary, and metavolcanic rocks. The movement of the detachment fault causes the rocks on the upper plate to be severely fractured and brecciated thus making them Ideal conduits for mineralizing fluids. Mineralization favored the more reactive sedimentary and volcanic rocks of the upper plate. Three gold deposits, located in upper plate rocks, are currently being mined along the Colorado River corridor: the Picacho Mine near Yuma, Arizona, 70 mi south of the study area; the American Girl Mine In southeastern California, 60 mi southwest; and the Copperstone Mine near the southern end of this study area. Samples from the above three mines were used to create a geochemical model of detachment-related gold deposits. Antimony, arsenic, barium, copper, mercury, molybdenum, manganese, tungsten, and zinc all occur In the mine samples in concentrations at least three times greater than found elsewhere in similar rock types. Samples taken by the Bureau from the wilderness study areas contain similar anomalous concentrations of the same elements as well as elevated concentrations of several other elements Including: lead, fluorine, cerium, uranium, and samarium.

Jan 1, 1992

By Robert A. Cummings

A rock mass classification system has been developed for support estimation in mines using caving methods. The developed system (MBR System) accepts readily-obtainable geotechnical properties, and mining geometry, to develop a rating that permits recommendations for drift support in block caving mines. The data base includes major active United States caving mines. The method is intended to be used for planning and estimating purposes and for preliminary support design. The Manual explains the organization and nature of the MBR System, its derivations, details of required input data, methods for assessing the data and for developing rock mass ratings, and techniques for selecting the most appropriate mine support recognizing mine requirements and desired stability. A worked example is provided.

Jan 1, 1984